Search:

Type: Posts; User: Crazecodyk

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. I'd be more inclined to monitor start ups. Have...

    I'd be more inclined to monitor start ups. Have him cycle the unit to simulate it cutting off. It's not enough just to let it run and sit and ponder. Screw waiting a few days. Cycle that sucker to...
  2. Replies
    28
    Views
    869

    504741 This is how I roll. Sent from my...

    504741
    This is how I roll.


    Sent from my iPhone using Tapatalk
  3. Replies
    28
    Views
    869

    The ladder rack is going on next week. Double...

    The ladder rack is going on next week. Double side let down. Then using the system to hang six footer from inside roof of cab area. It's getting where we need a 6',8', and 24' at all times


    Sent...
  4. Thread: 80+10 mfd ?

    by Crazecodyk
    Replies
    6
    Views
    281

    Sounds like you need a meter that reads...

    Sounds like you need a meter that reads capacitance...


    Sent from my iPhone using Tapatalk
  5. Replies
    28
    Views
    869

    So far after 3 fill ups fully loaded averaging...

    So far after 3 fill ups fully loaded averaging 14-15 mpg mostly intown stop and go traffic. Roughly 1500-2000 in the back at all times. More when equipment is in it.


    Sent from my iPhone using...
  6. Thread: Bryant txv

    by Crazecodyk
    Replies
    89
    Views
    3,557

    I just got a bulletin from Bryant saying they...

    I just got a bulletin from Bryant saying they recognize the tx void sue and had a replacement procedure for the bad valves..


    Sent from my iPhone using Tapatalk
  7. Replies
    28
    Views
    869

    504321504331504341504351 Sent from my iPhone...

    504321504331504341504351


    Sent from my iPhone using Tapatalk
  8. Replies
    28
    Views
    869

    Just bought one for my new tech. Partly to try,...

    Just bought one for my new tech. Partly to try, other part is due to lack of fords or Chevys. Found several used fords for 25 range. I got my pro master for around 29. With bin package. They only...
  9. I've got a few of those doing same thing at a...

    I've got a few of those doing same thing at a facility I work on. What the technical book says is either bearings or gear motor relay being weak. For my situation it ended up being the relay

    ...
  10. Replies
    10
    Views
    984

    Low voltage or line voltage fuse? Sent from...

    Low voltage or line voltage fuse?


    Sent from my iPhone using Tapatalk
  11. Replies
    40
    Views
    1,975

    This is common and does happen when it's only a...

    This is common and does happen when it's only a one way motor. Swap the power wires from the motor cap and make it go correct direction. No mystery about it.


    Sent from my iPhone using Tapatalk
  12. Replies
    14
    Views
    1,295

    I carry the 902. But have grown to like my 179...

    I carry the 902. But have grown to like my 179 more. I have a amp probe attachment for my 179 but i trust fluke.
  13. Replies
    2
    Views
    280

    Get your posts up and apply for pro membership...

    Get your posts up and apply for pro membership then we can help ya.
  14. Replies
    26
    Views
    2,256

    No way in hades can anyone give an accurate...

    No way in hades can anyone give an accurate pressure reading on a partially frozen coil! And for that matter. If you chose to just recharge the system make him use a scale and watch what he puts in....
  15. I would say over charged. Or fan motor cutting...

    I would say over charged. Or fan motor cutting out(i. E. bearings)
  16. Can't help ya out. Need to get your posts up then...

    Can't help ya out. Need to get your posts up then apply for a pro membership. Then maybe the troubleshooting can begin
  17. Second electric heat may be running. But if...

    Second electric heat may be running. But if there's a 20 degree TD idk. Unless readings are fudged......
  18. The secondary drain issue is not an issue for...

    The secondary drain issue is not an issue for this matter. If you want them to add it in just for your peace of mind then by all means ask them too. But in no way is that an install error. Labor is...
  19. Replies
    13
    Views
    1,144

    Lets get this strait.....checked amps on non...

    Lets get this strait.....checked amps on non running equipment.....replacement of 3 capacitors for two components.....and freon is good but the equipment isn't running so there's no real way to check...
  20. Replies
    14
    Views
    1,297

    I use the fluke 1587(i believe that's the correct...

    I use the fluke 1587(i believe that's the correct model number) it's a meggar/meter combo. Love it. Found plenty of nuisance problems, and i use it when my reg meter takes a plunge.
  21. Replies
    8
    Views
    1,559

    I use a d-tek on all freons. It doesnt like...

    I use a d-tek on all freons. It doesnt like finding 404 or 410, sometimes no problem, sometimes big problem. I picked up a new JB prowler that has a vibrating function that helps esp when it's in a...
  22. Replies
    5
    Views
    709

    I won't do a manual J until if got the job. The...

    I won't do a manual J until if got the job. The contractor was aware of the windows an insulation if he suggested a lower btu furnace. Manual j takes time. And if im seeing alot of customers just...
  23. Replies
    20
    Views
    1,646

    I use bow bender for everything i can. Regular...

    I use bow bender for everything i can. Regular and reverse bends. Cuts down on the amount of welds and it's pretty compact
  24. Biggest thing is make sure the compressor has a...

    Biggest thing is make sure the compressor has a sound blanket.
  25. Thread: Work boots!

    by Crazecodyk
    Replies
    122
    Views
    15,763

    I've always work wolverines. Was going through...

    I've always work wolverines. Was going through two pair a yr. last round i bought some redwings hoping that they'd last longer esp since they were 189.00. They are comfy but sadly no more life than 6...
Results 1 to 25 of 173
Page 1 of 7 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event