Search:

Type: Posts; User: JayATS

Search: Search took 0.00 seconds.

  1. Replies
    85
    Views
    5,524

    "All you gotta do is"

    "All you gotta do is"
  2. Replies
    11
    Views
    2,657

    Real nice work there.. This should be in the wall...

    Real nice work there.. This should be in the wall of fame not the wall of shame.
  3. Replies
    12
    Views
    1,631

    OK so here is how I think I may do it.. still not...

    OK so here is how I think I may do it.. still not sure if its right but.. I'll use the amp draw I got from my meter of 40 amps and lets say 5% of that watt out put is my heat load that equals 920...
  4. Replies
    12
    Views
    1,631

    I'm in a factory setting and this is for machine...

    I'm in a factory setting and this is for machine electrical cabnets unvented
  5. Replies
    12
    Views
    1,631

    Not being electrical savy all I have to go on is...

    Not being electrical savy all I have to go on is volts x amps = watts and I believe that is where I am getting confused.
  6. Replies
    12
    Views
    1,631

    heat/load calc for elec. cabinets

    I've been tasked by my boss to determine if we have enough cooling for the electrical cabinets in our facility. I personally have never done a heat/load calc for electrical cabinets. I have done...
  7. Replies
    2
    Views
    443

    Leaking plate heat exchanger

    We have a water cooled chiller that uses plate heat exchangers. It developed a refrigerant leak and water has now contaminated the whole system. As far as I know the compressor is still fuctional...
  8. Well basicly anything over 4ft you gotta be in a...

    Well basicly anything over 4ft you gotta be in a genie here.
  9. Your lucky... The place I work at your not...

    Your lucky... The place I work at your not allowed to go over 4ft on any size ladder. Anything over 4ft you need a harness and a tie off point. If you get caught over 4ft without that equipment you...
  10. Thread: Stink bugs!

    by JayATS
    Replies
    6
    Views
    1,223

    Call Billy the exterminator? lol I have had...

    Call Billy the exterminator? lol I have had several no cool calls for bugs stuck in a contactor but I have never had a unit that size go down.
  11. Replies
    4
    Views
    816

    Trane compressor

    I have a Trane compressor Mod#3E5R60W Ser#TS-4573 that I believe I have a restricted oil strainer.. The only literature I have for this dates back to 1973 for a similar compressor Mod#3E5B60 what im...
  12. Replies
    42
    Views
    2,692

    I believe with most carrier boards if you lose...

    I believe with most carrier boards if you lose voltage across limit or rollout the blower motor will run continous. I dont think a limit is your problem most likely you have a bad board. You can...
  13. Replies
    3
    Views
    568

    As a dog lover and a bull terrier owner this is a...

    As a dog lover and a bull terrier owner this is a great story!! thanks for sharing.
  14. Replies
    4
    Views
    1,345

    You should never try and fix a bad gas valve...

    You should never try and fix a bad gas valve always replace it. but check for gas flow from the meter.
  15. Thread: help

    by JayATS
    Replies
    4
    Views
    386

    As per the AOP Rules only Professional Members *...

    As per the AOP Rules only Professional Members * can reply with
    advice to the OP. Anyone may post and ask questions. They may even
    question the * member answer but not give advice or expand on the...
  16. Replies
    8
    Views
    1,662

    The boilers we have here in this plant all have a...

    The boilers we have here in this plant all have a fire eye control that will not allow the burners to run 100% unless there is 40# steam pressure present. I still like to bring them up manually as...
  17. Replies
    31
    Views
    2,726

    A crack is a crack and the safety of your...

    A crack is a crack and the safety of your customer is in your hands. Turn it off, and if the customer turns it back on after you leave the liability is in his/her hands now.
  18. Replies
    1
    Views
    469

    I'm in the Peoria area.

    I'm in the Peoria area.
  19. Replies
    2
    Views
    443

    New from Illinois

    I decided to join here after doing some research online for some of my "problem childs" and this site always seemed to come up with alot of great info.
Results 1 to 19 of 22
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event