Search:

Type: Posts; User: perfectionist

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    15
    Views
    909

    The carpenter on this job was awesome! He...

    The carpenter on this job was awesome! He actually shaped and fitted each log on site with great precision. I was very impressed with the workmanship. He did a great job calking all the log seams...
  2. Replies
    15
    Views
    909

    the condensate drain should be trapped with an...

    the condensate drain should be trapped with an air gap to prevent sewer gas/smells to enter the home air spaces.[/QUOTE]

    All of the drains are 3/4" cpvc that run to a common 1 1/2" drain that runs...
  3. Replies
    602
    Views
    9,842

    I don't care

    I don't care
  4. Replies
    11
    Views
    2,397

    Nice looking install and the vapor barrier puts...

    Nice looking install and the vapor barrier puts it over the top!
  5. Replies
    15
    Views
    909

    Thanks to all that replied.

    Thanks to all that replied.
  6. Replies
    15
    Views
    909

    Yes there is also a propane gas "wood"stove for...

    Yes there is also a propane gas "wood"stove for back-up but the hyper heats will be the work horse.
  7. Replies
    15
    Views
    909

    Yea that was kind of a comprise. The customer...

    Yea that was kind of a comprise. The customer wanted it hidden as much as possible. I will have to look and see if there is a way to have the vanes set to an angle or horizontal. Thanks for the...
  8. X2 it's the condensation issue

    X2 it's the condensation issue
  9. Replies
    15
    Views
    909

    Log Cabin Hyper Heat

    This is a new log cabin that I was asked to come up with a heating solution for. Any gas furnace would have been too big and the duct work would either had to have been exposed or installed in a wet...
  10. Replies
    21
    Views
    841

    A camera would tell you a lot. It may be worth...

    A camera would tell you a lot. It may be worth renting or getting a plumbing co. involved that has a snake with a camera on it.
  11. Replies
    18
    Views
    1,772

    Looks great....Your metal always looks good. ...

    Looks great....Your metal always looks good. Does the ICP have a PSC or ECM? Have you ever used a zone handler on a zone system? They work nice instead of having to install a by-pass.
  12. Replies
    12
    Views
    627

    If you want to slow the circ. speed and the drive...

    If you want to slow the circ. speed and the drive the speed up when htg or cooling then a Fanhandler is the only way to go.
    www.fanhandler.com/
  13. Replies
    6
    Views
    1,463

    We lose more helpers that way!

    Was wiring in my A/C breaker when I saw this. How would you like to be the one to draw the short straw. I think it powers the floor sander?!!?
  14. I've been using the kick start as well KS-1 is...

    I've been using the kick start as well KS-1 is good to 5 tons
  15. Replies
    22
    Views
    2,298

    You have to where a lot of "hats" and I work long...

    You have to where a lot of "hats" and I work long hours but I don't think that I could go back to work with people that say close enough or can't see it from my house ever again.
  16. Maybe not but you could service one as soon as...

    Maybe not but you could service one as soon as tomorrow.
  17. In my area I was told the supply pressure before...

    In my area I was told the supply pressure before the regulator is 75#. Then regulated down to 7" W.C.
  18. Replies
    16
    Views
    630

    Whiskey ..... Drink it don't put it in your eyes!

    Whiskey ..... Drink it don't put it in your eyes!
  19. Replies
    16
    Views
    630

    I welded for years and had multiple flash burns....

    I welded for years and had multiple flash burns. Extreamly painful and there is nothing you can do. Flash burn is when the cornea is burned off your eye and it takes 24 hrs to regenerate
  20. Replies
    22
    Views
    2,298

    Thanks.......I do that on every furnace/coil that...

    Thanks.......I do that on every furnace/coil that I have room for.
  21. Replies
    22
    Views
    2,298

    Lol...waitng for sparky to run a wire over then I...

    Lol...waitng for sparky to run a wire over then I will wire it up.
  22. Replies
    22
    Views
    2,298

    Tape first so it doesn't indent the armor flex?...

    Tape first so it doesn't indent the armor flex? Not a bad idea I may use that. As far as the vanes they were extra but I had already figured the TEL for the system with out them.
  23. Replies
    22
    Views
    2,298

    Thank you. It's nice to be in the club.

    Thank you. It's nice to be in the club.
  24. Replies
    22
    Views
    2,298

    They probably look long in the pic, but the...

    They probably look long in the pic, but the intake and exhaust are about 30' of pipe and the equivalent length of the fittings is 14'. The manual says I can go 135', plus I have found if I keep the...
  25. Replies
    22
    Views
    2,298

    The new energy code......ducted supply AND return.

    The new energy code......ducted supply AND return.
Results 1 to 25 of 438
Page 1 of 18 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event