Please kindly email me your contact info.
Thanks
Type: Posts; User: pete_d
Please kindly email me your contact info.
Thanks
b-man
Could you please email me too?
Thanks
Pete
Turbomaster, please kindly email me 06N manual too. Thanks
mtnwrench, How much does it cost you for this software?
Thanks
I want to have part number of Fiber Optic Cable with connectors connecting between TRANSMITTER BOARD p/n 031-02576-000 and GATE DRIVER BOARD p/n 031-02575-000.
I look into 160.00-RP5 (706) MEDIUM...
May I get your email too?
Thanks;
I think that it may relate to the software on a new screen.
Thanks
They are listed under hvacpartners.com > product > Water-Cooled Chiller > 30XW > Documents and Downloads. See attachment.
I want it since I have to replace a failure control screen.
FLR1592 can replace FLR928. It is longer but same diameter and thread.
Screwit,
I want to contact you but can not find your email in your profile. Please send me an email.
Thanks
Pete_d
I want these service bulletins:
SMB09-0036: 30XA/XW Chiller Software Revisions
SMB09-0045: 30 Series Chiller Pump Control
They are available in hvacpartners.com under service which I do not...
Thank you so much.
Please email me CVHE-SB-22A.
Thanks
Please help me.
I want the wiring diagram and spare part list manual of Carrier (France) 30HG 320 901--EE.
Its nameplate is attached.
Thank you in advance
From the attached picture, is it considered as a defect rotor?
Rotor Bar Test results No current fluctuates at 55VAC 80Amps.
The motor winding was burnt out.
What is the TRANE Motor Rotor...
Please help me for 19XR CVC Software CESR-131158-04.
Thank you in advance.
Hello
Can someone here please email me the 19XR CVC Software CESR-131158-04?
Thank you in advanve.
Scewit
Please kindly email me CGGA & CGGB 047-080 manuals.
Thank you so much
Hi everyone
I want these manuals:-
CGAE-IN-3 Cold Generators Air-Cooled
CGAE-M-3 Air Cooled Cold Generators
CGAE-W-2 Wiring Manual
CON-AM-24
Please kindly email me. My email is in my...
You can replace the dynaview (with correct MP software) from its twin to see the result.
If you do not know how to download MP software properly, it is DANGEROUS to your machine.
The float valve is stuck.
There are 2 possible causes:-
1. Touch Screen sensor of Dynaview fails to provide correct position.
2. The MP software of Dynaview is corrupted.
I would recommend to download a new MP software...
What are the major causes for TRANE CHHC Screw Compressor motor burnout?
Can I have sb0041 to study?
Thank you
The carrier chiller model 19XL5353304CR S/N 1994Jxxxxxx has an intermittent alarm.
The alarm message in alarm history is
'CMPD 221.0 F exceeds limit of 220.0 F, Check Discharge Temperature'.
...
I work on one 19DR machine that has High Discharge Temperature trip.
We ran it for 2 hours and have the following data.
The oil temp is 140-145F. The suction superheat is about 4F.
The measured...
The left side of Digital I/O Board is called Digital Input (DI) Lines and Right Side called Digital Output (DO) Lines.
The Control Point (CP) is the software program that drives one or more Digital...
Please! email me York form 450.20-NOM1 and BACnet Microgateway Operation Manual (450.20-??).
Thanks
No email addresses in post
Please read site rules, Thank you.
Can your guy email me TRANE CTV-SB-48?
Thanks in advance
pete@pvt-worldwide.com
It is York YT 300 Tons chiller. There is no tube leak. The tube sheet leak are at both ends. Is it recommended to do tubes eddy current test? What is the estimated cost?
Thanks;
We found the leak at water cooled condenser tube sheet nut tubes.
The water inlet pressure is 70 psig. The chiller refrigerant is R123.
What do your guy do to repair this kind of leak at tube...
I think so.
Check your email.
Djken, Can I have your email address? Removed email
Please put email in your profile!
Check your email.
For those who have it, please kindly email me. My email is in my profile.
Thanks
Please send me an e-mail.
My e-mail address is in my profile.
YORK "L" is ISO 120 POE Oil used with DXS Screw Compressor on YCWS/YCAS Chiller.
If blank screen means dark, check the cable from Micro Board to Inverter Board next to the Display or the display lamp is poor.
Yes, your right. Thank you
I like to get your email address.
check your email
"S" oil is the replacement of "G".
I want to uninstall MP software from CH530 Dynaview (or BLANK it out) and move it to another chiller (different model) to INSTALL new different MP with TechView.
What is the procedure to uninstall...
What is your email? Cannot find it in your profile.
I like to get your old board to learn.
Check your email.
If the micro board get the correct supply (per wiring diagram) from power board, the micro board is dead.
No.
The port to check oil pressure is after the oil filter.
The port to get the oil to check is the port at the oil sump where you will take oil out and fill new oil in.
I have to change some starter configuration to eliminate False (nuisance) Alarm on Trane CVHG chiller with CH530 Main Processor (MP) software Ver. 10.02 with IT Solid State Starter.
The lasted MP...
RLC-SVD04 is for Compressor Diagnostic Troubleshooting Repair.
RLC-SVD05 is for CH530 Control Diagnostic Troubleshooting repair.
For CVGF, I only know IOM.
TRANE commercial chiller tech support Email & Phone wanted.
Thank you;
There is sometimes Fault Alarm "Phase Reversal" on CVHG with CH530 and "IT" Solid State Starter when STARTING the motor.
The Line Power Phase is CORRECT with Phase Rotation Indicator (CW).
"IT"...