Search:

Type: Posts; User: gotparts90

Page 1 of 5 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    24
    Views
    4,260

    belzona some good stuff but its needs to be real...

    belzona some good stuff but its needs to be real clean where it goes. and if its going to be a thin layer drill into the material a little bit in a few spots to let it get a better bite. I have used...
  2. Replies
    10
    Views
    1,277

    Title said Chicago but ad posed says St Louis, Is...

    Title said Chicago but ad posed says St Louis, Is it Chicago? if it definitely is I will email resume, but is it union?
  3. I am in the same boat I have over 5 years in and...

    I am in the same boat I have over 5 years in and a C card but am out of work I am helping out at a friends shop (non fitter work non union) but only have a few days here and there. I am taking...
  4. Replies
    22
    Views
    3,122

    One problem is the tangs are to hard, I would...

    One problem is the tangs are to hard, I would rather the tang wear first and have to change the pump then the crank wear a circle and the pump tang spin then need a crank and that 1 out of 20 for the...
  5. Replies
    22
    Views
    3,122

    They last longer than 5000 hours if they never...

    They last longer than 5000 hours if they never run hot. Oversized valves?? do you mean ZBAE? they AE has the bigger suction plates and valves but the discharge is the same. If you order parts by...
  6. Replies
    4
    Views
    630

    Take the test it is worth trying, I took it and...

    Take the test it is worth trying, I took it and was I think ranked 6th but had a foot problem and could not start my apprenticeship. I wish I did but between having about 6 months of a bad tendon...
  7. Replies
    4
    Views
    630

    C card, I was getting over C card pay but I am in...

    C card, I was getting over C card pay but I am in class for B card right now.
  8. Replies
    4
    Views
    630

    Looking for work in the chicago area

    I can email my resume I have 5 years with york union 597 in class at the hall currently. need work bad thanks. Most experience with large recip units all makes and models.
  9. Replies
    6
    Views
    1,003

    25 30 is about right it has an adjustable...

    25 30 is about right it has an adjustable regulator on it. open the cap on top over the pump crank it down a little if you need to. I think yorks shop just tossed all those out if you need a rebuild...
  10. I no longer work for the york shop in wheeling...

    I no longer work for the york shop in wheeling but I did like those tranes F and E better than the J. The unloaders had no side loading force to them the engineers did a better job thinking those...
  11. Replies
    13
    Views
    991

    i have extra inputs on my car just for my friends...

    i have extra inputs on my car just for my friends to hook up to at the beach or party for my system. It is 4 extra RCA's for the mids highs and subs. NO RAP my cars blasts Zepplin, ZZtop and floyd....
  12. Inducer motor assembly for carrier furnace

    Inducer motor assembly for carrier 58DFA07c-7c its is being a pain trying to find a part number for this. I'm looking for the entire unit with blower wheel and back fan all together. if any one has a...
  13. Thread: Ps3

    by gotparts90
    Replies
    1
    Views
    864

    ps3 is the **** just put linux on mine and going...

    ps3 is the **** just put linux on mine and going to try to play bioshock on it
  14. Replies
    8
    Views
    838

    i cant tell you the supplier in china that makes...

    i cant tell you the supplier in china that makes them because i work for york, not trying to be a dick but they pay me not you. if you get any cmp parts i like the fit and finish of them but try to...
  15. Replies
    8
    Views
    838

    let me see if i can get a pdf off the computer or...

    let me see if i can get a pdf off the computer or snag some from up in the office but if you just want torque spec i could rattle them off to you. for clearance just buy new parts the rods are always...
  16. Replies
    2
    Views
    678

    i have ear plugs and muffs,sometimes i put my...

    i have ear plugs and muffs,sometimes i put my shure noise reducing ear plugs in with my ipod then ear muffs over for a good workday
  17. Replies
    8
    Views
    1,613

    it is the same thing. 12-45 will be the same...

    it is the same thing. 12-45 will be the same process. do you guys change the bearings and gas seals while you have it open? and mutulivech is da boss but mukul anud is the GM MR. while it last six...
  18. Replies
    8
    Views
    1,613

    i work at the Chicago shop and our boss is the...

    i work at the Chicago shop and our boss is the guy who runs Baltimore parts. i know if you call and talk to someone from the back of the shop we'll help you but good luck being on hold with...
  19. Replies
    11
    Views
    1,831

    otto my friend needs a new nextel in mount...

    otto my friend needs a new nextel in mount prospect you still got it?
  20. Replies
    6
    Views
    784

    some German stuff is double square on cars i...

    some German stuff is double square on cars i wonder if they are doing to other stuff now. it looks like torx but is 8 point internal.
  21. Replies
    8
    Views
    3,118

    i wanted to make one like that but from behind...

    i wanted to make one like that but from behind the doors back to match my van as a camper. I was looking for an extended van for better balance.
  22. Replies
    24
    Views
    2,124

    i love dye but thats because i get overtime for...

    i love dye but thats because i get overtime for jacked up compressors killed by it but it does make me look bad when the die kills them again. If the comp runs a little to hot that crap turns to a...
  23. Replies
    15
    Views
    2,055

    sweet baby rays all the way. its from the west...

    sweet baby rays all the way. its from the west side crack heads in Chicago that know how to bbq
  24. Thread: Wiha Tools?

    by gotparts90
    Replies
    5
    Views
    1,013

    loved my wiha screwdrivers until the carpet flyer...

    loved my wiha screwdrivers until the carpet flyer grabbed them for intense chiseling they are a bit to hardened and brittle but great quality machining if you dont hit on them they are great
  25. Replies
    4
    Views
    1,212

    when it starts up all the cylinders become loaded...

    when it starts up all the cylinders become loaded until you apply power to unloader to unload cylinders. The extra unloader is do to lazy people in my shop and in your office not getting to the the...
Results 1 to 25 of 106
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event