Search:

Type: Posts; User: adamt

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. jtrammel, I like your avatar photo, I'm hoping to...

    jtrammel, I like your avatar photo, I'm hoping to make my crawlspace look like that soon.

    Adam
  2. 13% humidity isn't uncommon in Denver in the...

    13% humidity isn't uncommon in Denver in the summer. Wouldn't a bypass humidifier reduce the airspeed even more? The fan speed is at its lowest setting right now for circulation and I like how quiet...
  3. Humidifier Recommendation for a York Affinity

    I would like to add a humidifier to my furnace, a York YP9C 100k btu. I am a little concerned that there won't be enough air speed to properly humidify my house, any recommendations? I can't really...
  4. Thread: York Cfm Led

    by adamt
    Replies
    3
    Views
    634

    Thanks, I'll let him know. That actually makes...

    Thanks, I'll let him know. That actually makes sense too, go figure.
  5. Thread: York Cfm Led

    by adamt
    Replies
    3
    Views
    634

    York Cfm Led

    I had a new furnace and a/c installed this last winter and I couldn't be happier with it, or the installer. The furnace is a YP9C 100C and the a/c is a YCJF48S41S with an MC48C3XH1 coil.
    From what...
  6. Replies
    15
    Views
    1,581

    I tested all three of the sensors and the one...

    I tested all three of the sensors and the one that I am using was the closest to actual temperature, the resistance reading translated to about 1.5 degrees warmer than what the actual temperature...
  7. Replies
    15
    Views
    1,581

    I used 18/2 solid conductor wire. I haven't had a...

    I used 18/2 solid conductor wire. I haven't had a chance to measure the resistance and compare it to the specified value for the temperature. The tech will be here tomorrow or Monday and I will have...
  8. Replies
    15
    Views
    1,581

    Having the remote sensor dictate the temp is what...

    Having the remote sensor dictate the temp is what I am after, I just can't seem to get the remote to measure the actual temperature. The remote sensor is in the nursery where our 5 month old twins...
  9. Replies
    15
    Views
    1,581

    Why Won't My Remote Sensor Read Correctly?

    I have a Honeywell Vision Pro IAQ Thermostat with a wired remote temperature(and humidity) sensor and I can't get the remote sensor to give an accurate temperature reading.The furnace, a York YP9C,...
  10. That actually is the approach I've been using. I...

    That actually is the approach I've been using. I replaced all of the recessed lights with IC units and installed airtight baffles, foamed all of the attic bypasses and blew in another 14" of...
  11. Thanks for the input on the location, I'll let...

    Thanks for the input on the location, I'll let the installer know that I'm more confident about it now.
    I looked at the steam unit, but it has a couple strikes against it; price of the unit and...
  12. How Far Above The Coil Does A Humidifier Need To Be?

    I just had my furnace and a/c installed(York YPC9) and my cased coil goes all the way to the branch ducts. I would like to put in a humidifier, but my installer and I are hesitant about cutting into...
  13. Replies
    9
    Views
    985

    What Size A/C Disconnect?

    I have a friend(Journeyman Electrician) coming over this weekend to install an a/c disconnect for the system being installed next week and I need to know what size disconnect to pick up and this will...
  14. Replies
    84
    Views
    3,084

    As one of the people that rely on this site for...

    As one of the people that rely on this site for expert opinion, I would appreciate you keeping the current policy. I find it encouraging that the "Pro's" actually have to establish themselves as...
  15. Thanks everyone, I appreciate your help.

    Thanks everyone, I appreciate your help.
  16. Can a Six Inch Concentric Vent Be Used For Two Appliances?

    Can a six inch concentric vent be used for a HE water heater plus a furnace? The vent uses 4" pipe for the combustion air and vent, can it be used instead of two three inch concentric vents? I know...
  17. Replies
    21
    Views
    1,515

    I just called another company, this one non...

    I just called another company, this one non Union, and they want twice as much as the first guy. I may just pay my Father in Law to come out here from Mn to do it, he still has his tools and EPA...
  18. Replies
    21
    Views
    1,515

    I'm not sure where the cost of brazing is coming...

    I'm not sure where the cost of brazing is coming from, do you guys always cap linesets that aren't going to be reused? I just don't want to be the guy that just releases the freon into the atmosphere...
  19. Replies
    21
    Views
    1,515

    Pretty much except that I may not replace it at...

    Pretty much except that I may not replace it at all and if I do I can get up to $1,500 rebate from Excel for "trade in". Right now the only function the condenser is serving is as an obstacle. I...
  20. Replies
    21
    Views
    1,515

    Different trade.

    Different trade.
  21. Replies
    21
    Views
    1,515

    I just realized that this is the wrong forum. ...

    I just realized that this is the wrong forum.

    Mods, could you please move this to the ask the pros forum?

    Adam
  22. Replies
    21
    Views
    1,515

    The unit is 10-12 years old, I wouldn't reuse the...

    The unit is 10-12 years old, I wouldn't reuse the lineset , it has a blown compressor, it's oversized, the soldering was done incorrectly and it's directly under the main circuit panel for the house....
  23. Replies
    21
    Views
    1,515

    I Want to Remove My Condenser

    I called the company that diagnosed my compressor as bad this summer to have them come out and evacuate the system so I could move the condenser and pour a new patio. I was surprised to hear the...
  24. Thread: I am pi$$sed

    by adamt
    Replies
    8
    Views
    1,545

    I have been having great luck on Craigslist. Just...

    I have been having great luck on Craigslist. Just include "made in USA" on your searches. Planned obsolescence wasn't always the way things were designed. I just purchased a 10 year old Weber grill,...
  25. Replies
    8
    Views
    1,527

    Two of them quoted York systems to me last year....

    Two of them quoted York systems to me last year. I couldn't afford either of them, the prices are much better this year, but on different equipment.

    Adam
Results 1 to 25 of 55
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event