Search Results - HVAC-Talk: Heating, Air & Refrigeration Discussion

Search:

Type: Posts; User: frost

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    73
    Views
    3,004

    Converted back to lp control that it came with...

    Converted back to lp control that it came with was one step you had taken. With out all the data I am just wondering is the differential is too wide?
  2. Replies
    16
    Views
    4,251

    I carry a box of different sized ID cap tube and...

    I carry a box of different sized ID cap tube and cut to fit mfd spec. The argument I have for replacing the whole thing is almost every old cap tube has build up material on its walls and is already...
  3. Replies
    31
    Views
    2,182

    Stainless can take some good cleaning agents. You...

    Stainless can take some good cleaning agents. You can even use lime away. I need some feed back on the filter I think you need a 25 micron? Not filtering is a very bad thing. Make sure to flush a new...
  4. Replies
    13
    Views
    1,365

    On a 404a system no bubbles in the sight glass...

    On a 404a system no bubbles in the sight glass isn't an accurate determination of refrigerant charge. For R12 this generally works well. R404a is a blend of two refrigerants and must be introduced to...
  5. Replies
    16
    Views
    1,300

    It might be possible to simply have the condenser...

    It might be possible to simply have the condenser relocated on your property. I suggest as close to the home as possible in a location it can breath. If an objection is aesthetics pretty it up with...
  6. Replies
    16
    Views
    3,608

    If the pet smells are from your pets there is a...

    If the pet smells are from your pets there is a UV light that will break them apart. Its not the standard UV light. This one is mounted in another location. If you have no pets and don't smoke you'll...
  7. Replies
    12
    Views
    785

    That is great that you have thoroughly inspected...

    That is great that you have thoroughly inspected the heat exchanger for cracks and have no low lvl poisoning going on. If it would truly hold water I think you should donate it to your local HVAC...
  8. Replies
    72
    Views
    5,326

    Or if hes afraid the nitrogen will get left...

    Or if hes afraid the nitrogen will get left behind in the compressor after you vacuum the system you'll be fine. Just watched that video. Its good.
  9. Replies
    72
    Views
    5,326

    They don't stay together when pressurized. You...

    They don't stay together when pressurized. You have to keep an opening and a constant 0.5 psi or so. Its also not a great idea to wet cool a weld. They have more integrity if allowed to slowly cool,...
  10. Replies
    1
    Views
    1,478

    A true gentleman. Some people would just sell em...

    A true gentleman. Some people would just sell em a new one:)
  11. Replies
    31
    Views
    2,150

    I don't think a 20 year warranty is at all...

    I don't think a 20 year warranty is at all common. Until recently a lot of heat exchangers have had more like a 10 year warranty. Most systems are expected a life of 13 to 18 years or so. I inspect...
  12. Replies
    59
    Views
    13,127

    I would have your tech go through the condition...

    I would have your tech go through the condition of your evaporator before running your new compressor and make sure it gets a crank case heater. There could be a cause to your compressor failure left...
  13. Replies
    7
    Views
    454

    The impact is damage and increased running...

    The impact is damage and increased running expense. Not only must the wheel be symmetrical, but if even one counter weight is moved or removed while cleaning or installing it should effect the...
  14. Replies
    32
    Views
    4,396

    Tell me a little more. Its my understanding the...

    Tell me a little more. Its my understanding the stem will always be set in the mid point. Are you saying if I have 3 they could all be set differently or just the fact that mid point simply isn't a...
  15. Thread: Scotsman DC30A-1

    by frost
    Replies
    4
    Views
    806

    The guys at scottsman have always been pretty...

    The guys at scottsman have always been pretty helpful with info. They have a disk with all models you might be able to get them to send you one. Might have to give them your contractors license...
  16. Replies
    10
    Views
    2,023

    So its a potential relay or a current relay. Make...

    So its a potential relay or a current relay. Make sure the current relay isn't up side down. It happens. Some potential relays can be subject to poor placement as well. potential relay #5 goes to...
  17. Replies
    7
    Views
    1,677

    There is soft wear for some of these...

    There is soft wear for some of these calculations. All the glycol systems I have been responsible for it was good enough to toss some valves in the bypass and throttle them to adjust flow rate. Just...
  18. Replies
    32
    Views
    4,396

    TXVs are factory set. If its not working the...

    TXVs are factory set. If its not working the problem is likely many many other things. How ever when they have a damaged component and need to be changed the replacement should work fine with factory...
  19. Replies
    14
    Views
    1,710

    I didn't see you actually say the Thermal...

    I didn't see you actually say the Thermal expansion valve had any grit in its screen. So is it possible the gray dust is from the compressor crank shaft and rods ect? Id guess it was still passing...
  20. Replies
    2
    Views
    2,146

    I'm told we will soon be using psc motors in...

    I'm told we will soon be using psc motors in bathroom fans. The energy savings if every one got rid of all those shaded pole motors would be quite high state wide. I could see something like the...
  21. Replies
    20
    Views
    3,142

    It sounds like your sensitive to that florescent...

    It sounds like your sensitive to that florescent flicker. I too have often been over come and fatigued by that pulse under florescence. Kind of like when people have seizures from video games.
  22. Might as well have your professional leak check...

    Might as well have your professional leak check the rest of your supply lines while you have them out. Sounds like it could be some time before you have any one out again. Sometimes a safety check...
  23. Replies
    11
    Views
    2,539

    Its most likely the furnace heat exchanger had a...

    Its most likely the furnace heat exchanger had a life expectancy around 18 years or so. That puts this unit around 12 years over due for a change out. I feel its in the landlords best interest to...
  24. Replies
    146
    Views
    36,407

    Sticky: I don't see my self on the map, but I think it...

    I don't see my self on the map, but I think it may be best if I only say really good things about my employer from here on out. LOL. Anonymity brings out the worst in ppl.
  25. Thread: Heating a room

    by frost
    Replies
    3
    Views
    472

    Are you building the area for this purpose or...

    Are you building the area for this purpose or just wanting to put some inexpensive heat source in there to hold 104 f? That space would be nice to have some floor heat and a good deal of insulation...
Results 1 to 25 of 34
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event