Search:

Type: Posts; User: gophers17

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    388

    X2

    X2
  2. Replies
    2
    Views
    205

    Thanks rundawg, most appreciated!

    Thanks rundawg, most appreciated!
  3. Replies
    2
    Views
    205

    Carrier Blower Curve

    Hi all! Looking for a blower curve chart for a Carrier = Mod#58MCB060-12112 Ser#4111A02447.
    Thanks in advance.
  4. Replies
    7
    Views
    843

    lol:whistle:

    lol:whistle:
  5. Replies
    47
    Views
    3,100

    Like everyone else is saying, nothing beats a...

    Like everyone else is saying, nothing beats a Redwing set of boots. Their more comfortable then some of my tennis shoes...
  6. Hahahaha.. funniest thing ive seen on here yet!

    Hahahaha.. funniest thing ive seen on here yet!
  7. Replies
    21
    Views
    1,523

    The coldest ever that I have worked in was -35 F,...

    The coldest ever that I have worked in was -35 F, after accounting the wind chill it was -63 F. You stay warm by running inside every 5 minutes!
  8. Thread: resi techs

    by gophers17
    Replies
    11
    Views
    813

    We leave them 3-4 space heaters until we can get...

    We leave them 3-4 space heaters until we can get there for the install, but make sure to get a credit card number for "collateral" of the space heaters and document how many you left, problem solved...
  9. Replies
    5
    Views
    814

    No, basically just split system resi. not so many...

    No, basically just split system resi. not so many heat pumps.
  10. Replies
    5
    Views
    814

    Micron Gauge Location?

    This may be a silly question, but I finally ordered a micron gauge that I will directly hook up to my crt. My question is does it matter which line to hook the micron gauge up too? (suction or...
  11. Not the Coleman!! Nothing but problems!

    Not the Coleman!! Nothing but problems!
  12. Replies
    36
    Views
    4,617

    Had kind of the same call last week, turns out...

    Had kind of the same call last week, turns out the homeowner had some plumbing fixed and the wonderful plumber torched the LV wires going out to the condenser while putting in a valve. Saved the...
  13. Replies
    31
    Views
    1,716

    Both i suppose, we have been doing AC tune-ups...

    Both i suppose, we have been doing AC tune-ups the last few weeks and its been between 50*F - 60*F so we have been using it to check refer levels as best we could, just put a load on the house with...
  14. Replies
    31
    Views
    1,716

    Fieldpiece makes a "charging jacket" that covers...

    Fieldpiece makes a "charging jacket" that covers the top of the condenser during low ambient to raise the head pressure. We use it up here in MN and it works pretty well, it has a bungee cord to...
  15. Replies
    0
    Views
    253

    Profile name?

    Does anyone know if there is a way to change my profile name? ie. gophers17
  16. Replies
    135
    Views
    23,260

    So what is the difference between super seal and...

    So what is the difference between super seal and EZ seal? My company uses EZ seal when applicable but it scares the S@#$ out of me so I wont use it. Asked the boss man if he thinks it works and the...
  17. Im in the same boat as Hurtinghvac was, about a...

    Im in the same boat as Hurtinghvac was, about a month out of school been with the company for the same amount of time and just thrown to the wolves! I love it tho and am learning more than i thought...
  18. Thread: tapa talk 2

    by gophers17
    Replies
    1
    Views
    302

    tapa talk 2

    Is it worth the few bucks? Is it any easier to navigate the forums with it? Thanks in advance!
  19. I am just about done with school and have landed...

    I am just about done with school and have landed a job luckily, but I was strictly taught sc and sh for charging. OAT+30 was only taught for a general condenser temp. But I had a good teacher!
  20. Replies
    7
    Views
    986

    Thanks for the replies! Ya no leaks its just...

    Thanks for the replies! Ya no leaks its just kinked maybe 30 to 40 percent of I.D. Brand new house and contractor didn't packed ground in good enough and when it sank the lines were kinked. I thought...
  21. Replies
    7
    Views
    986

    kinked lines?

    How bad is it on a system if the suction and liquid lines are kinked a little bit?
  22. Replies
    30
    Views
    18,355

    This. But after looking closer it does just look...

    This. But after looking closer it does just look like a saftey certificate as you guys said. My bad, just curious.
  23. Thread: pic test

    by gophers17
    Replies
    1
    Views
    471

    test

    test
  24. Replies
    30
    Views
    18,355

    Ya that makes sense, thanks for the info!

    Ya that makes sense, thanks for the info!
  25. Replies
    30
    Views
    18,355

    410 A

    Sorry don't know how to highlight, but what is the 410 A certificate for if you don't need one to purchase it?
  26. Thread: test

    by gophers17
    Replies
    26
    Views
    4,786

    Test

    Test
  27. Replies
    6
    Views
    1,142

    Just took mine a few weeks ago. Not to difficult...

    Just took mine a few weeks ago. Not to difficult if you can study the booklet. Another good site to look at is escoinst.com they have practice tests for the 4 areas and are very helpful.

    Good luck!
  28. Replies
    7
    Views
    1,456

    Hahaha

    Hahaha
  29. Replies
    54
    Views
    3,822

    Good to hear. I'm at hennepin tech in the cities...

    Good to hear. I'm at hennepin tech in the cities at the moment doing hvac. I was just curious.
  30. Replies
    54
    Views
    3,822

    I know its a bit off topic for the thread, but...

    I know its a bit off topic for the thread, but which school do you teach at?
  31. Thread: test

    by gophers17
    Replies
    26
    Views
    4,786

    Test:censored:

    Test:censored:
  32. Replies
    118
    Views
    14,824

    I'll be 30 exactly by the time i start as well....

    I'll be 30 exactly by the time i start as well. Better late than never!
  33. Sticky: Finally

    Hi guys/gals. Been cruising around here for months after I decided to take the dive and go to to school for the HVAC tech. trade. Been learning a lot on here and as well in school. Thanks to all who...
Results 1 to 33 of 44
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event