Search:

Type: Posts; User: Ricky Dale

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Add the supply's. The garage isn't air tight. Co2...

    Add the supply's. The garage isn't air tight. Co2 monitors need to be in sleeping quarters. It fine to have them in every room but your fine here add them.
  2. Replies
    31
    Views
    1,806

    Coleman has an archives if you want to see if the...

    Coleman has an archives if you want to see if the model number is listed. It's just an old furnace and very reliable. We had a Coleman plant here Barber Coleman that made them here. Not in 1936 but...
  3. Sounds like you have a low ambient temp. and your...

    Sounds like you have a low ambient temp. and your cooling to a low temp. You may want to control the fan motor on the condensing coil so the refrigerant can condense, Set it to keep the condensing...
  4. Replies
    46
    Views
    2,476

    Contact the hvac board in your state and submit a...

    Contact the hvac board in your state and submit a complaint, Tell them the name of the roofer and what he did and that he will not correct it. They will come out and his bond will be used to correct...
  5. Replies
    40
    Views
    1,656

    When you attach you manifold gauges. The guage to...

    When you attach you manifold gauges. The guage to the right that reads you discharge pressure. Know which refrigerant you using r-22 or 410-a. The color of the refrigerant cylinder matches the color...
  6. Replies
    70
    Views
    7,123

    Goodman unit get a bad rap cause of the failure...

    Goodman unit get a bad rap cause of the failure of there equipment. Goodman unit keep a lot of people in business. I replaced an OD unit a little while back that was leaking at the bottom of the...
  7. A lot of people make this mistake. Never use the...

    A lot of people make this mistake. Never use the same color wire. always associate a wire color to a number. I like something I can remember like red white blue l1 l2 l3. Also for what it's worth...
  8. Replies
    14
    Views
    1,081

    As stated the limit/safety is tripping because...

    As stated the limit/safety is tripping because the chamber is getting to hot due to the indoor blower stopping or slowing enough allowing the heat to not be removed from the heating chamber,...
  9. Replies
    21
    Views
    1,244

    Ohm out the compressor and do an amp draw on it...

    Ohm out the compressor and do an amp draw on it when it starts. Its likely pulling to many amps cause the internal mechanical parts are beginning to seize. if it's old and it sounds like it is put a...
  10. Replies
    14
    Views
    811

    Follow your line voltage and control voltage from...

    Follow your line voltage and control voltage from the transformer. Someone has feed line voltage to the control side or they have shorted together. Trane secures there wiring to short.
  11. Replies
    40
    Views
    1,656

    if the unit tripped the breaker your first stage...

    if the unit tripped the breaker your first stage or both stages compressor's internal mechanical parts are seizing causing the unit to pull to many amps. Do an amp draw on startup and make sure the...
  12. Replies
    6
    Views
    297

    Thanks

    Thanks
  13. Replies
    6
    Views
    297

    Thanks i know that. Let me explain a little...

    Thanks i know that. Let me explain a little better about what were working with here, It's in a large public education environment. The thumbwheels are disabled. So the units cycle based on the...
  14. Replies
    6
    Views
    297

    The thumbwheel is disabled. the setpoints are set...

    The thumbwheel is disabled. the setpoints are set at 74 cooling and 71 for heating. My question is should the heating high limit be not be higher than the heating setpoint and the cooling low limit...
  15. Replies
    6
    Views
    297

    Trane Tracer high low limit question

    I have a question about the heating high limit and cooling low limit setpoints in Trane's tracer summit software. I read that the heating and cooling high and low limit setpoints 'CAP' the operating...
  16. RUNDAWG: I need your wisdom on a Trane actuator motor operation.

    Hello: Forum

    Rundawg, I have a couple questions on the operation of Trane actuator motors installed on a four pipe Trane fan coil unit.
    The actuator motor is...
  17. Replies
    0
    Views
    324

    cycling of fan coil blower motor

    From time to time I work on four pipe Trane fan coil units. They are controlled by Trane's tracer summit software. My question is what cycles the blower motor? The best I can figure is when the space...
  18. Thank you mason

    Thank you mason
  19. Replies
    8
    Views
    658

    The spark module is integrated into the board. ...

    The spark module is integrated into the board. Situation is understood my thanks to mason and a big thanks to rundawg.
  20. Order of safety checks Trane package gas.

    I've gotten conflicting information concerning the order in which the roll out and limit switch are checked to be closed when the there is a call for heat. one person stated the pressure, roll out...
  21. Replies
    8
    Views
    658

    Right you just jarred my brain safetys are...

    Right you just jarred my brain safetys are checked first. Thanks the ignition board is bad. I appreciate you.
  22. Replies
    8
    Views
    658

    My mistake yes the limit switch location. Once I...

    My mistake yes the limit switch location. Once I can confirm the limit switch location and that it is closed i'll know if the ignition board is faulty. The connection are made from the ignitor...
  23. Replies
    8
    Views
    658

    L

    L
  24. Replies
    8
    Views
    658

    L

    L
  25. Replies
    0
    Views
    289

    Trane XL 1600 package gas.

    I have a Trane XL 1600 to look at Monday. So far I've gotten the tech. on the job to confirm the inducer motor runs then the pressure switch closes and that's there is ctrl. voltage between w1 and...
  26. Replies
    8
    Views
    658

    limit rollout switch

    Hello: I have a call to go to on a Trane XL 1600 package gas. I'm short on time with this and would like to know exactly where the limit rollout switch is located. So far I've been told the inducer...
  27. Replies
    75
    Views
    50,114

    Sticky: I didn't ask if it was rocket science i asked...

    I didn't ask if it was rocket science i asked wher is the additions tab.
  28. Replies
    75
    Views
    50,114

    Sticky: additions tab

    where do i find the additions TAB?
  29. Replies
    75
    Views
    50,114

    Sticky: I am so glad to see that members must conduct...

    I am so glad to see that members must conduct themselves verbally as professionals. Thank you very much hvac-talk.
  30. Replies
    35
    Views
    4,625

    answers for heat pum question in Pa.

    A heat pump isn't recommended for you all up there unless it has a new 16 seer plus rating. You all get to cold of weather. make sure no water can drip on your coils and make sure you have drains...
  31. Replies
    18
    Views
    7,857

    suggestion to intermitting defrost problem

    Your defrost board may have an issue which hasn't totally failed.
  32. Replies
    15
    Views
    1,357

    Your sister should have a 5 ton unit. If the...

    Your sister should have a 5 ton unit. If the service man charged me $ for a service call and to add refrigrant, i would tell him to reclaim it and put the $ towards a new unit.
  33. Replies
    10
    Views
    2,766

    This split unit is on top of a high school and...

    This split unit is on top of a high school and the personnel before me i know didn't clean any RTU coils. First stage works fine in heat as well as cool mode. Second stage will frost over on both...
  34. Replies
    10
    Views
    2,766

    I have a 2 stage, 4 compressor Trane split water...

    I have a 2 stage, 4 compressor Trane split water source heat pump that has a problem in the 2nd stage. My liquid line is frosting on both sides of my filter/dryer. I've changed the power head. The...
  35. Replies
    102
    Views
    17,221

    Happy new year! I appreciate the assistance you...

    Happy new year! I appreciate the assistance you all have given me in 09 and look forward to being a more knowledgeable therefore better technician by you alls help this year. Ricky Dale.
  36. Replies
    102
    Views
    17,221

    aren't complimented enough.

    aren't complimented enough.
  37. Replies
    102
    Views
    17,221

    Mr: jpsmith: Thank you i agree totally. People...

    Mr: jpsmith: Thank you i agree totally. People who speak in a negative tone are not happy people and create a negative environment. I personally think they are complimented enough by people...
  38. Replies
    102
    Views
    17,221

    I've bent the ears on a ballists 90 degrees when...

    I've bent the ears on a ballists 90 degrees when 208 joilted me. I don't want any more than that. I've been working around 477 volts for years and never been hit. I respect it very much. We have...
  39. Replies
    102
    Views
    17,221

    Thanks

    Yes you have
    Thank you
  40. Replies
    102
    Views
    17,221

    I work in the field m-f 6:30 to 3 pm. I also have...

    I work in the field m-f 6:30 to 3 pm. I also have my own licensed business. I keep a a800 plus high school operating and well as changing out household units and troubleshooting them. Also some duct...
  41. Replies
    102
    Views
    17,221

    I applied for pro status. I'm hvac certified,...

    I applied for pro status. I'm hvac certified, universal epa certified and will be gas certified on november 21st. We all have questions from time to time i'm just not embarrassed to ask what i need...
  42. Replies
    102
    Views
    17,221

    everything is cool guys. I'm licensed and i'm...

    everything is cool guys. I'm licensed and i'm taking my gas license test next month in gulf shores alabama. I also have my universal epa certification. May i add i'm also a certified computer...
  43. Replies
    102
    Views
    17,221

    research

    I do online rearch and am currently studing for my gas license which i will also have this month. I usuall work on single pahse and am certantly still learning. Thanks
  44. Replies
    102
    Views
    17,221

    compressors

    Ok i got it ; like i thought but always verify. I work on a lot of different water source heat pumps and also split heat pumps, dual fuel rtu's 20 tons and larger. Sometimes i get in a little of a...
  45. Replies
    102
    Views
    17,221

    info

    Thanks
  46. Replies
    102
    Views
    17,221

    New post need to ask simple questions and confirm...

    New post need to ask simple questions and confirm therories. professional well attituded people in converstation. So i would personality take an ohm reading from the l1 l2 and l3 to ground and put my...
  47. Replies
    102
    Views
    17,221

    getting the posting in to ask useful questions,...

    getting the posting in to ask useful questions, what's wrong with that?
  48. Replies
    102
    Views
    17,221

    What will my fieldpiece display when i'm checking...

    What will my fieldpiece display when i'm checking for a grounded winding to the housing if the compressor is bad?
  49. Replies
    102
    Views
    17,221

    What should the ohm reading display on my...

    What should the ohm reading display on my fieldpiece meter when the l1 l2 or l3 lines are bad?
  50. Replies
    102
    Views
    17,221

    Do i check the l1 l2 and l3 lines in for...

    Do i check the l1 l2 and l3 lines in for infinity on my ohm meter? Do i listen for a tone?
Results 1 to 50 of 235
Page 1 of 5 1 2 3 4

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Comfortech365 Virtual Event