Search:

Type: Posts; User: ZoneRider

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    23
    Views
    1,259

    Agreed , Bypass dampers on zoning systems when...

    Agreed , Bypass dampers on zoning systems when applied to modern equipment does not make sense , one thing we do with our system when applied to 2 Stage VS Split Systems is that we give you 2 sets of...
  2. Replies
    20
    Views
    1,695

    Properly designed and set up zoning systems work...

    Properly designed and set up zoning systems work great , when our system is applied to 2 Stage VS Split Systems our zoning control gives you 2 sets of Y1 Y2 outputs , one for the blower section and...
  3. We offer a GEO specific zoning product and often...

    We offer a GEO specific zoning product and often do custom panel builds that combine forced air and radiant zoning , you can always look us up at www.arzelzoning.com or contact us at 1-800-611-8312...
  4. Replies
    3
    Views
    886

    Hey !!! There's my C-Clamp !! I wondered where...

    Hey !!! There's my C-Clamp !! I wondered where I left it !!!
  5. Replies
    140
    Views
    7,487

    I carried a nice oil drain pain from Summit...

    I carried a nice oil drain pain from Summit Racing that closed up nicely without leaking and spilling , drained my pump while she was nice and hot , most companies give you the oil to do it so why...
  6. Replies
    3
    Views
    450

    Yes this is one option , lol Other than...

    Yes this is one option , lol

    Other than that , With the age of the unit and depending on your skill level you may only be able to eliminate what is most likely low ambient controls and...
  7. Replies
    3
    Views
    345

    I would think it would be best to be controlled...

    I would think it would be best to be controlled away from the supply registers , see if the installing contractor can install balancing dampers for the supply's effected , near the equipment to...
  8. Thread: grease

    by ZoneRider
    Replies
    4
    Views
    379

    I never did , they're cheap and easy to replace...

    I never did , they're cheap and easy to replace if necessary , I always figured the oils in the refrigerant is sufficient enough to keep them conditioned , plus I would think grease would attract...
  9. Replies
    3
    Views
    345

    I think maybe you need to post this question in...

    I think maybe you need to post this question in the "Ask Our Professionals" forum but.....

    Maybe check if the trunk or branch dampers have manual hand balancing dampers ( a little lever with a...
  10. Replies
    27
    Views
    1,800

    Just remember NEVER burn a bridge , you may need...

    Just remember NEVER burn a bridge , you may need to cross it again someday ! You have to remember too that the principles of these companies see each other at organization meetings , trainings ,...
  11. Replies
    12
    Views
    688

    Not knowing what the performance of the hydronic...

    Not knowing what the performance of the hydronic coil is , what the supply air temps will be , what the existing motors rated operating temps are , etc.... My SWAG tells me if its a PSC motor you'll...
  12. Replies
    14
    Views
    896

    Dont think its what you have going on but I once...

    Dont think its what you have going on but I once had a customer call me late one evening that the system I just commissioned and started up wasn't working and the thermostat blew up ? I drove out to...
  13. Thread: not sure

    by ZoneRider
    Replies
    3
    Views
    236

    +1 on that

    +1 on that
  14. Thread: rla and fla?

    by ZoneRider
    Replies
    3
    Views
    296

    Do a search , there are actually several threads...

    Do a search , there are actually several threads covering this question , here's one ......

    http://hvac-talk.com/vbb/showthread.php?168282-RLA-verses-FLA&highlight=running+load+amps

    Hope this...
  15. Replies
    15
    Views
    845

    Checking the blower rotation would be my starting...

    Checking the blower rotation would be my starting point as well , if the motor is running the wrong rotation then its doing very little work , less work = less amps ....
  16. Even with a properly designed system there's only...

    Even with a properly designed system there's only one thermostat for the whole house , it only knows what the temperature is in "that" room , combined with load shift , the sun beating down on the...
  17. Replies
    13
    Views
    1,245

    Designed correctly and Installed correctly zoned...

    Designed correctly and Installed correctly zoned Small Duct High Velocity systems can work great , First and foremost the system needs to be installed following the OEM manufactures recommendations ,...
  18. Replies
    5
    Views
    370

    Possibly , but you'll need to try and find a...

    Possibly , but you'll need to try and find a model & serial # somewhere located on the unit ........
  19. I made a similar mistake and that's all it was ,...

    I made a similar mistake and that's all it was , a mistake , except I posted on the AOP like 5 times in one day , and the moderators were understanding about the situation . I didn't read the "rules"...
  20. Thread: Controls

    by ZoneRider
    Replies
    5
    Views
    399

    Steve , just my 2 cents but I dont think anything...

    Steve , just my 2 cents but I dont think anything will teach you these skill better than "hands-on and on the job" training . I'd try first to apprentice with a good company in your area that does...
  21. Replies
    2
    Views
    330

    I would think it would be a possibility , start...

    I would think it would be a possibility , start with "simple stupid" issues before looking for more complicated ones . Probably the easiest way to determine if its the stat would be to take the stat...
  22. Thread: 3 heat sorta

    by ZoneRider
    Replies
    5
    Views
    304

    There's many ways to skin this cat , and a lot of...

    There's many ways to skin this cat , and a lot of it depends on how the homeowner wants things staged and/or locked out , as well as what controls the wood burner . Should the boiler be considered as...
  23. Thread: 3 heat sorta

    by ZoneRider
    Replies
    5
    Views
    304

    Wouldn't he want to have the wood fired boiler as...

    Wouldn't he want to have the wood fired boiler as primary heat and then if the wood boiler goes cold then allow for the heat pump and then finally add in electric resistance if needed ? Maybe use a...
  24. I apologize

    I apologize
  25. Replies
    12
    Views
    510

    This is the Ask Our Pro's forum, and only Pro...

    This is the Ask Our Pro's forum, and only Pro members that have been vetted by the AOPC may post advise, commentary, or ask questions of the OP here.

    You can find the rules for posting and...
Results 1 to 25 of 30
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event