Search:

My buisiness partner and i just recently returned from a trip to the goodman manufacturing plant, airfare, lodging meals, and a professionally guided fishing trip were included and all paid for by...

I agree with the last two posts, not a very good install at all.

anything to do with carrier whether it be bryant or payne is not a good product, i have customers tell me they want anything but carrier in their home, that tells me alot about a product when a...

Just went to goodman 13 seer seminar last night to see what they are all about, and from what i could see they will be giving everyone else some competition in the near future, not saying i will push...

That goodman coil has a different style orrifice ( the thing in the plastic bag, it is used to meter the refrigerant to the coil) than a trane orrifice, or does the coil have a TX valve (thermal...

ADP is a good quality coil, have installed a few in the past, as far as warranty goes i'm not too sure as i only install them, but it's a quality product

on call, how many ductboard systems have you installed compared to metal systems, by the tone of your defensiveness it sound like you don't use metal at all, many postings on this site have dealt...

as long as they are sized corectly and installed properly there is nothing wrong with ceiling registers, don't know why you would go in the sidewall if you have a full attic to work in, seems like a...

Chillbilly, seems you and i are the only ones that still use metal ducts in this thread, i don't know if that means no one knows how to size and install metal or what but it is very obvious in my own...

Just what i figured, it's all about the sale, i would turn down a job if the customer wants duct board (politely of course) but with 15 years in buisness i have never had a customer request it, as...

I can't believe this conversation is going on so long, if you duct board guys want me to believe that you would pick duct board over metal if offered side by side both at a comparable cost i think...

duct board is junk no matter how you look at it,any reasonable person would come to the conclusion that over the years of air moving at a fairly high cfm through it that it will break down and start...

duct board is no good if you ask me, it breaks down over time and you end up blowing fibreglass all over your house and many people end up with respratory problems, you can insulate metal ducts on...

why a filter drier, doesn't trane\american standard come with one factory installed inside the condenser

we use slimduct on all installs that are exposed, it looks professional and is easy to use, and the customers love it, gutters are old school and don'tlook all that great, the slimduct line of...

never said the question was about if it's code , just saying it is code where i do my work

In Mass it's code to run them seperately, won't pass inspection if they are in the same conduit, and yes the inspectors do actually check it

Around here we call it a canadian cold trap and it works fantastic, just like the previous posts site run it to floor level and double 90 it up and you will never have a draft unless equiptment is...

Just put one in last week and as baldloonie said only the nameplte flips over and the power pack stays the same, and yes the on \off switch is upside down but it doesn't affect the opperation of the...

not trying to get anyone upset, just saying at my company we always change to b-vent for code reasons, and our own peice of mind

That furnace is a 2 pipe unit, why did they add combustion air for it????

Your models blower has a 2,000 cfm capacity on high speed , so since it is capable of moving 2,000 cfm you need return out of both sides, one side and bottom , or the bottom, even though you say your...

Me too , when we remove a furnace and install new, we need to change the flue to all b-vent, plus in that kind of room i would put b-vent anyways

I install rheems all the time and on a 120,000 you definately need both sides , the bottom, or one side and the bottom for proper return air , and you say the noise isn't as bad with the 6" filter...

Here in Mass we are having trouble getting ten seer stuff also, just last week i bought the last ten 2.5ton condensers my american standard dealer had, just want to be prepared for those tight...