Search:

Type: Posts; User: Bill Bednarick

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    21
    Views
    4,949

    I've seen something similar with units that have...

    I've seen something similar with units that have a delay on make timer on them to prevent short cycling when the stat is being fiddled with..
    The timer works properly most of the time, but every so...
  2. Replies
    5
    Views
    3,032

    I am always amazed at the amount of work the...

    I am always amazed at the amount of work the Amish have to do to live in our world while staying true to theirs.

    If you get it sorted out take some pictures and post them here I know I'd like to...
  3. Replies
    13
    Views
    1,669

    A good way to practice controlling the torch is...

    A good way to practice controlling the torch is to take an old piece of tubing and drill some 1/4 holes in it then braze them shut and leak check it.
  4. Replies
    7
    Views
    1,572

    Anyone know where to get more info on the Franke...

    Anyone know where to get more info on the Franke freezers?
    I've worked on one and all the nameplate info is gone.
    It would be nice to know what the charge weight is supposed to be.
  5. Replies
    29
    Views
    2,334

    If they did they probably figured it was "not...

    If they did they probably figured it was "not their problem" kind of like when they notice the condenser coil covered with dirt and crap and ignore it till the food is warm.:D
  6. Replies
    9
    Views
    1,099

    I bet it was made of stainless steel.

    I bet it was made of stainless steel.
  7. Crot

    I haven't had one that popped yet when I unscrewed the cap yet, most of the ones I've seen go bad just caused very low suction pressure and wouldn't adjust to give more.
    Sounds like you did the...
  8. How did you decide the Crot was bad?

    How did you decide the Crot was bad?
  9. Barback cooler question. Two evaporators, one compressor.

    So I have a new customer with a barback cooler that consists of 2 coolers sharing the suction and liquid lines from the compressor. It has always been controlled by a low pressure switch and the...
  10. Replies
    16
    Views
    1,194

    Do you also add a receiver? Or just charge to the...

    Do you also add a receiver? Or just charge to the nameplate amount?
  11. Replies
    410
    Views
    33,540

    I've seen the new manifold and it looks very...

    I've seen the new manifold and it looks very good.
    But I'd still like to have a micron gauge on them.:D
    I'm looking at getting a Digicool soon.
    I just have to convince the Boss.;)
  12. Replies
    15
    Views
    2,383

    Don't forget "locked in".;) Coolers and freezers...

    Don't forget "locked in".;) Coolers and freezers are always trying to do this.
  13. Replies
    15
    Views
    923

    You wouldn't have any part numbers for these...

    You wouldn't have any part numbers for these would you?
    I asked at my local place and they couldn 't find anything for this application.
  14. Replies
    43
    Views
    2,524

    I wonder if the Emerson Performance Alert box...

    I wonder if the Emerson Performance Alert box would be of any help.
    It protects against single phasing and monitors so you can pull a report off the box and tell what it has been doing....
  15. Replies
    12
    Views
    3,354

    Evidently the people that design them have never...

    Evidently the people that design them have never visited some of the places people use them in.:D:D:D
    "Why won't the reach-in next to the fryers hold temp?";)
  16. The guys that will work for less will always be...

    The guys that will work for less will always be out there, in computers there is always someone that "knows computers" that can help you. Problem is most of the time they either lose money or make...
  17. Replies
    15
    Views
    923

    http://hvac-talk.com/vbb/showthread.php?t=230022...

    http://hvac-talk.com/vbb/showthread.php?t=230022

    :D:D:D
  18. Replies
    4
    Views
    427

    I've never worked on one but here is the install...

    I've never worked on one but here is the install manual for the case.
    http://www.master-bilt.com/pdfs/io_manuals/md-mdt_io_3-8-06.pdf
    And here is what it says about the orit.

    "The EPR valve...
  19. Replies
    13
    Views
    985

    http://www.noventcaps.com/images/productInfo2.gif

    http://www.noventcaps.com/images/productInfo2.gif
  20. Replies
    40
    Views
    2,253

    If it pulled down into a vacuum fairly rapidly...

    If it pulled down into a vacuum fairly rapidly then I'd think cap tube restriction so changing the cap tube is a good idea.
    You should change the oil, and the drier at the same time.

    I was taught...
  21. Replies
    40
    Views
    2,253

    It should be a critical charged system and have a...

    It should be a critical charged system and have a tag that tells you the amount of refrigerant required.
    If you have questions as to the current charge, your best bet is to recover the charge and...
  22. What was his reasoning behind it? Did you talk...

    What was his reasoning behind it? Did you talk with him about it or did you just come in behind him to clean up the mess?
    Also did he attempt to change out the oil? What kind of system was it?
  23. Replies
    25
    Views
    1,329

    I also saw this when I got interns from our local...

    I also saw this when I got interns from our local Vo-Tech school to work in our IT Dept.
    You'd get a couple that were on fire to learn everything you could teach them, then you'd get the ones that...
  24. Thread: hello

    by Bill Bednarick
    Replies
    10
    Views
    629

    Tree guys use lots of rope, some for rigging some...

    Tree guys use lots of rope, some for rigging some for climbing.
    http://wesspur.com/rope/rope-climbing-line.html
  25. Replies
    11
    Views
    901

    Yup, I don't understand. I do understand that...

    Yup, I don't understand.
    I do understand that no one but the person that screwed the cap tube on would know 100%.
    Sorry I couldn't be more help.
Results 1 to 25 of 71
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event