Search:

Type: Posts; User: kls-ccc

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    3,381
    Views
    138,164

    0w, ow, I know,I know, . . . Cause s**t...

    0w, ow, I know,I know, . . . Cause s**t happens!!!!
  2. Replies
    3,381
    Views
    138,164

    No, what he's asking is where is all the...

    No, what he's asking is where is all the righteous indignation against all the things that cause people to die from heart disease etc. because there are 2000% more deaths from that, than there is...
  3. Thread: sequencer

    by kls-ccc
    Replies
    35
    Views
    4,343

    I ran into one of these several years ago, went...

    I ran into one of these several years ago, went through 3 sequencers before I figured out it was the air flow that was keeping the sequencer engaged. The back panel was hot where the sequencer...
  4. Replies
    6
    Views
    245

    I've had a problem with IE for a while now, like...

    I've had a problem with IE for a while now, like before the H-talk hack was announced. So when that was announced I figured it was just part of that. It does seem to be better now but I have gone...
  5. Replies
    1
    Views
    146

    That depends on the design of the pan. Most...

    That depends on the design of the pan. Most newer pans are designed to pretty much empty they have built in slopes toward the drain opening. Other pans mainly older ones are flat pans with a drain...
  6. Thread: sequencer

    by kls-ccc
    Replies
    35
    Views
    4,343

    The unit was designed to work properly with the...

    The unit was designed to work properly with the sequencer in that location. You should not have to do anything to the sequencer unless it's bad. Fix the problem not the symptom.
  7. Your problem is air flow, too much here ~ not...

    Your problem is air flow, too much here ~ not enough there. It's a fairly common problem especially on spec homes. My guess is that you have the same size runs to every room in the house, the...
  8. Replies
    54
    Views
    1,022

    They do, or at least they did. There for a while...

    They do, or at least they did. There for a while they were making a big deal about how they did something with cornstarch in the mix to make them degrade in sunlight faster.
  9. I you are going to have the set point down for...

    I you are going to have the set point down for over 8 hours fine but don't set it down over 5 degrees. That system and stat should take care of itself and hold the back up heat out if it is not...
  10. We did a old house with a hot tub in the...

    We did a old house with a hot tub in the basement. We were concerned about humidity but to the best of my knowledge it was never an issue. They kept it covered when not in use. They may have had a...
  11. Our church has one similar. It's about 4' over...

    Our church has one similar. It's about 4' over from the stat and bigger like 6x12, but still close enough to blow on it. What's really odd I think is why would you put two registers at the back of a...
  12. Replies
    28
    Views
    1,478

    The blower should not be running until 45 seconds...

    The blower should not be running until 45 seconds after the burner fires. If it's running with no flame either the fan switch is on or it's locked out.

    You got a model#?

    Does the pressure...
  13. Replies
    54
    Views
    1,022

    This all falls into my theory of wealth. ...

    This all falls into my theory of wealth. California is a relatively rich state meaning they have a lot of people with a lot of money. That's not to say everyone is rich but there are a lot of...
  14. You shouldn't have taken off the plastic...

    You shouldn't have taken off the plastic deflector before you took the pic. It makes all the difference.
  15. Replies
    17
    Views
    704

    The best way to be fast and good is to not waist...

    The best way to be fast and good is to not waist steps. Plan what you are doing so you don't have to go back. Putting in X then having it in your way the rest of the install just slows you down. ...
  16. Replies
    7
    Views
    215

    Seems like I have played with something like that...

    Seems like I have played with something like that in the past. We built a box around the blower and put a filter in it. In a couple we left it like that in others we tied it into the return duct...
  17. Replies
    25
    Views
    661

    Talk to your electrician, I bet there is an easy...

    Talk to your electrician, I bet there is an easy way to make it work correctly, by code.
  18. Replies
    17
    Views
    704

    Just guessing but I would say: Don't pull the...

    Just guessing but I would say:

    Don't pull the flex tight.
    Don't properly support it.
    Don't worry about kinks.
    Don't worry about smashing runs.
    Don't worry about properly taping the flex....
  19. Replies
    7
    Views
    215

    Never put a filter AFTER a wood burner. There is...

    Never put a filter AFTER a wood burner. There is too much fire potential. If you put a good filter before the unit you should have no issues.
  20. Replies
    25
    Views
    661

    Here's a simple question for you, is there a...

    Here's a simple question for you, is there a light bulb or 120v receptacle in the room?
  21. Replies
    54
    Views
    1,022

    I don't know that it would really make a...

    I don't know that it would really make a difference in how much plastic enters the environment either as litter or into the landfill. Maybe we're just cheap around here maybe just thrifty but most...
  22. Yes, I was being sarcastic. Half of the stuff on...

    Yes, I was being sarcastic. Half of the stuff on the news is misdirection or of no consequence the other half is misreported and editorialized.
  23. Replies
    28
    Views
    1,080

    It is normal for the line to sweat but for there...

    It is normal for the line to sweat but for there to be that much water it sounds like the compressor is sweating also which it shouldn't under normal conditions. If the compressor is sweating that...
  24. Seriously, Radical Islam IS NOT a threat but IS...

    Seriously, Radical Islam IS NOT a threat but IS being rammed down our throats, but Climate change IS a threat that ISN'T being rammed down our throats by the same media. When did this happen?
  25. Replies
    13
    Views
    634

    X2

    X2
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event