Search:

Type: Posts; User: thecomp

Page 1 of 3 1 2 3

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    1,562

    Thank you!:o

    Thank you!:o
  2. Replies
    6
    Views
    1,562

    Belt Tension on Old Trane Air-Handler 1984

    I have an old Trane Air Handler, about 1984 vintage (BWH240B400DA). Sheave to blower pulley measures 18 inches, and it uses 2 B62 belts.I know the new Trane units use center to center divided by 64,...
  3. I found the configure data link and changed it to...

    I found the configure data link and changed it to cooling only.:)
  4. I thought so....thanks!

    I thought so....thanks!
  5. I'm in the process of going through the manual...

    I'm in the process of going through the manual now, but if someone can give me any specifics, it is appreciated.

    As for the new controller for heat, it is a Flexible System Controller by Johnson...
  6. Trane Intellipak Alarm: Heat Module Communication Failure

    I have a Trane Intellipak displaying a "Heat Module Communication Failure" after a contractor changed the heat control from the Trane Intellipak to another controller; this was last year, but I...
  7. Replies
    13
    Views
    1,613

    The old code 61 could be faulty barrel thermister...

    The old code 61 could be faulty barrel thermister and or the compressor thermister, crossed thermister sensor connections at the board, a bad microproccessor board "not likely", a chilled water valve...
  8. Replies
    1
    Views
    932

    Repoint a Chimney

    I need to repoint my chimney. Does anyone have advice or links to good info? I'm told you can buy mortor in a tube fro the job.:confused:
  9. Replies
    9
    Views
    1,345

    Kingsman

    I purchased the gas insert myself, so I need to find someone to help install it. If I didn't buy it from them, I don't think they will install. I got it at a great $ The gas pipe is no problem, but...
  10. Replies
    9
    Views
    1,345

    What is a Hearth Pro?

    What is a hearth Pro? A professioal fireplace installer? Where is the best means to find one in the Boston Area? Is a good Chimney Sweep enough?:confused:
  11. Replies
    9
    Views
    1,345

    Model IDFV33

    The Model is an IDV33, which specs a aluminum pipe and cap; however, the first chimney sweep I talked to recomended a galvanized cap: "Aluminum caps dont last." Would there be reaction between the...
  12. Replies
    9
    Views
    1,345

    The best 3" ducts for my Kingman Fireplace

    I'm an HVAC mechanic, and our shop is divided about what type of 3" ducts to install for my new gas fired Kingsman Fireplace. I know that a galvanized cap is best, but what material is best for the...
  13. Jayhawker, thank you for such an informative...

    Jayhawker, thank you for such an informative response. I was afraid of that. ej45, thanks for the offer, but I need to find support on a larger scale.:rolleyes:
  14. I would like to be able to troubleshoot the board...

    I would like to be able to troubleshoot the board and know what kind of voltages should be indicated such as the recent warrenty issue I had causing a "space pressue static alarm." Trane and I...
  15. Where is the best resource fro Trane Troubleshooting

    I need information for electrical troubleshooting new Trane equipment. Where is the best place for that? Electric voltage readings at the Human Interface control cabinets etc :rolleyes:
  16. Trane Intellipak alarms space pressure sensor failure

    I forgot to say that the space pressure sensor alarm is generated by the Human Interface Panel before the HVAC unit even starts.

    Where and what instruments are installed to check it out. The Trane...
  17. Replies
    114
    Views
    7,012

    Was the equipment nailed to the sheet rock...

    Was the equipment nailed to the sheet rock "foreseeable"? Probably not, so that a tough one for your legal arguement.

    Leaving you without much heat isn't great, but the electric should buy you...
  18. Trane Intellipak alarms space pressure sensor failure

    I have a Trane Intellipak which alarms a "space pressure sensor failure, so I replaced the transducer and solenoid; however, the alarm code "space sensor failure still appears. I traced out the 1/4'"...
  19. I found the red "rainbird" sensor barb fitting...

    I found the red "rainbird" sensor barb fitting broken, but with the help of a co-worker, I epoxyed a new fitting. It was raining at the time of the call. Blowing on the rainbird fitting seemed...
  20. Trane Intellipak Trips on Space Pressure Sensor Failure

    I have a Trane Intellipak M-(SSHFC254D), which trips on "Space Pressure Failure."

    I'm told it is most likely the transducer, but has anyone found this. Also, what is the 1800 number for Trane tech...
  21. Replies
    3
    Views
    1,176

    That will do it. Is there a web-site for...

    That will do it.

    Is there a web-site for carrier info?:)
  22. Replies
    3
    Views
    1,176

    Carrier WeatherMaker Model Number Needed

    I have a Carrrier WatherMaker and I need the Model Number. The name-plate is faded and I am missing one number from the Model number: M-50DJ00600 S-0889G28216

    The parts people at DCNE in Malden...
  23. Replies
    21
    Views
    2,683

    Most state only allow HVAC Techs to work on the...

    Most state only allow HVAC Techs to work on the "load" side of the disconnect. The new PPE rules are coming from NFPA 70E, but I haven't seen anything with regard to operation og disconnects, only...
  24. Replies
    0
    Views
    851

    Mass State School HVAC terrible

    I am an HVAC tech who is attending night college classes. The HVAC is terrible because of lack of fresh air. Although there are windows in most of the classrooms, students won't open them because of...
  25. Replies
    2
    Views
    640

    Thanks, good idea for a trend, which our control...

    Thanks, good idea for a trend, which our control people may already be doing because this is a new package unit. Both new rooftops are tripping on the 35-45F factory "low limit control", so maybe I...
Results 1 to 25 of 66
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event