Check with Redmond Williams in Mississauga.
Type: Posts; User: talktowags
Check with Redmond Williams in Mississauga.
Why would you want to do that ? A furnace is more efficient than a fireplace.
Success !!!
Tube heater.
The switch is likely doing what it is designed to do. Have a qualified tech check for vent blockage, secondary HE and temp rise. not sure why your not getting a flash code ? but with Nordyne anything...
As advised before, take all wires off board before crossing out R & W Had 2 where stat was causing that problem. Also had a goodman and turned out to be short in the ignitor.
I think you answered your own question. Lets see, you have a 28 year old Rheem ???
Seriously, go with the contractor you feel most comfortable with.
Welcome
Welcome. Lots to learn here and lots you don't need to know. LOL
Welcome, jump in !!
I started my Company in 1994 and new pretty much nothing about the industry. I hired an experienced tech and a helper to get started. I looked after sales, books, picking up and delivering materials...
If you have delayed ignition for whatever reason you may get a bit of raw gas passing through system on start up. Check burners and travel pilot. If HSI not getting hot enough, raw gas can pass...
With a job like yours, one would think you could afford a Sunday service call. ??
Sounds like it is a stat issue. What kind of stat are you using ? Older mercury stats have a heat antisipator adjustment. Best to replace if this is the case.
There is no way stove is operating properly with 1.5" wc. You have 12" before or after reg on the house ?? as stated above, you may be double reged. How old is the unit ? gas line could be sludged up.
Why not ask some of the guy's you work with.?? Or throw it around next time your at the supply house.?? DIY ??
Where is the Harthman ?? Good luck with a responce from TSSA I would cap & investigate further. Get Irving to tell you why and also what is the fix and who is paying for it. I would want some...
What do you charge to install wrong way ???
Are you working for a company ? if so maybe ask that a senior tech assists you on this one. Your messing with s**t that can and most likely will shorten your career. 13.5 out ?? I hope that is a...
No P # on switch. Guess I will call York. Thanks for the input.
G
Anyone know what pressure switch closes at on a York. Model # P9QDD12N09501A. Think about 22 yrs old. Pulling 1.33 thinking that is borderline. ????
Thanks in advance.
While I appreciate your input, you might want to read all the posts. Water in the trap ?? I hope so. A blocked trap will prevent ignition, but only after inducer starts. Any other thoughts ??
There is no way to wire board wrong. Only spade connections are for the transformer.
Sorry I am late getting in. 120v supplied to the board is through the molex connector. I have 24v at R. I have 120v at eac and motor is fine. No power to 5 pin molex when w is powered. I wired...
I am getting no power to the plug from the board. I put old board back in and I got my fault codes again. New board nothing. Will go at it again on Monday. Thanks for your input.
All 3 jack plugs are tight and yes I have 24v from tx. polarity is correct.
Working on a Goodman Model # GMV90905 DXA. Powered up unit, called for heat and board immediately gave a 3 flash code. ( Low fire p.s. stuck open ) inducer never started switch should be open ?? Took...
you have flame rollout caused by venting or heat exchanger. If venting is sized properly and heat ex is good, than I agree with extending vent another couple feet. Also could be a weak rollout switch.
Check heat exchanger & venting for blockage. But most likely not a slow opening valve. :.02::cheers:
Never had experience with Kozy but Heat & Glo is a good product. I have been putting in Majestic/Monessen and have had good luck. Hearthman is giving good advise. Go with contractor you feel...
Wow, I am going to stop worrying about 1/4 " per ft. rise. :cheers:
Piece of plywood and a brick. Protect the top of unit from ice off of roof. Should be good. :cheers:
You can buy heater cords that wrap around drain hose where it goes through the wall. Will require larger hole and a 120 rceptical to plug it into. :cheers:
How did you adjust the burners for smoother ignition ??:confused:
Welcome & enjoy. :cheers:
MRC42A is a wood burning fireplace ??? no need for gas line. If you want to install a gas log set than you should be hiring a pro. Not something to mess with yourself. :gah::cheers:
It is time for a pro to check things out and give you some options.:cheers:
Looks like they were trying to bring fresh air in from outside for some reason. Your furnace requires make up air for combustion. I see no reason to have it tied into your return air duct. As long as...
This is not a DIY site ( read the rules ) If power is on and door closed properly that power switch is engaged and still no go it is time to call a pro. Something shorted out on stat changeover. ...
What ?? Why ??:gah:
A pro could diognose in 5 minutes. Make the call !!!:cheers:
Why stop now ??? there must be some other parts you can change ??
Call a Pro. :gah::gah::gah:
Never to late. Good luck !! :cheers:
I agree. not even a green tech would go that route. :cheers:
No big deal Papa, as long as you can get gas line there and liner ( or 2 ) down the chimney. You might want to get 120V up there as well if you go with fan option. You have a on/off switch on...
So we agree. Board issue.:cheers:
If the code says p/s/ stuck closed than it is not drain/secondary/venting etc. You are getting a false code ( board ).
:.02:
:cheers:
If your cumbustion blower continues to run than there is still a call for heat. 2 flashes pressue switch closed . ?? should be closed on call for heat. Get company back with different teck. Sounds...
Wood insert or gas ?? :cheers:
Call a tech before you hurt someone.
233681