Search:

Type: Posts; User: Fmech

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    519

    automated logic lost password

    have customer with no access to system
    engineer left and took/changed password on his way out


    can anyone point me towards a work around or security file extension ??
  2. Replies
    5
    Views
    929

    carrier 19XL high bearing temp

    Getting an occasional fault per the engineer
    have not seen his machine yet to check logs. going there monday
    possible causes???
    oil levels are good and temps are at 138 degrees
  3. Replies
    3
    Views
    984

    Trane PCM software

    Thanx for the quick response.

    would anyone have an e-mailable copy of that software out there???
    and do I need an interface or just cable direct hook up. I have the parallel
    to serial patch...
  4. Replies
    3
    Views
    984

    Trane PCM programming

    Have a job with a problem PCM I need to upload the program and load into a new PCM board. I already have trane tarcer Rover version but I am pretty sure its not capable of loading a PCM. Can...
  5. Replies
    12
    Views
    2,468

    I have a front end computer there that hasn't...

    I have a front end computer there that hasn't been in use for ???? who knows
    what would be the suffix for the b/u file??
    the front end does have the graphics how ever tried a serial cables hook...
  6. Replies
    12
    Views
    2,468

    alerton

    Actually, I have both a copy pf the software (ibex for windows) and the parallel port "key"
    More specifically, i was looking for some assistance as to what my laptop hook up would be....
    through...
  7. Replies
    12
    Views
    2,468

    perhaps I don't have the exact correct name for...

    perhaps I don't have the exact correct name for this module
    Its a wall mounted back lit LCD display module with up down left right and N & P keys for navigating around to the individual VLC's that...
  8. Replies
    12
    Views
    2,468

    alerton microset

    Could I also trouble you for the same info
    I have a alerton microset that lost its program and am looking to scan the buss and reload the points

    THANX!!!!!!!!!
  9. Replies
    2
    Views
    731

    comfortview software

    Most software has the ability to upload and copy an existing program set up out of an existing controller and then down load it to another controller on the network.
    is there a carrier publication...
  10. Replies
    2
    Views
    731

    carrier comfortview controller programming

    have several jobsites that I need to replace VAV box controllers &/or reprogram
    337cfan & VAV controllers. Can this be done through the comfortview front end
    on the network?? or do I have to...
  11. Replies
    153
    Views
    36,469

    [QUOTE=HVACRACbob;7352592]230.10-m1 (804) ???????...

    [QUOTE=HVACRACbob;7352592]230.10-m1 (804) ???????

    Is this top secret???????

    Out of 100+ People Begging]

    After your tirade can we assume that you would like a copy of that form
    If so,...
  12. Replies
    153
    Views
    36,469

    you just might want to redo your email address in...

    you just might want to redo your email address in your profile, It's wrong
    yes, I resent it to your correct email address
  13. Replies
    153
    Views
    36,469

    in your email

    in your email
  14. Replies
    13
    Views
    1,174

    High current amps resolved

    After a LOT of calling around FINALLY got the info I needed.
    To any and all who may have followed this thread the following is the answer.
    For the millenium recip chiller control.
    the following...
  15. Replies
    13
    Views
    1,174

    Any york factory tecs outthere??

    Still having a hard time getting to the bottom of where the machine gets the correct amp rating for the over current parameter on this YCAR chiller.
    If any of you readers have any thoughts. After...
  16. Replies
    13
    Views
    1,174

    Eprom question

    he chiller had been running okay (to my knowledge)
    the building engineer had gone up to reset the unit after a bad storm
    and apparently left the access door loose and got some (or all) of the...
  17. Replies
    13
    Views
    1,174

    The dip switch settings match. the current draw...

    The dip switch settings match. the current draw (combining both wires for each phase is 71 + 72 = 143 though only one wire from each phase goes through the current sensor and one does not, as I...
  18. Replies
    13
    Views
    1,174

    its a split feed 2 wires per leg one each goes...

    its a split feed 2 wires per leg one each goes through the klixon and one does not
    I measured the 3 (separately) that go through and the three that don't
  19. Replies
    13
    Views
    1,174

    YORK YCAR0230 current sensor reads 50% to high

    I have a YCAR0230sc46P aadb SN RBKM6505AA
    unit is locking out on over current high amps reading of 160% @ 164 amps. The problem is that I'm reading 71 amps actual on all six feeders to compressor...
  20. Replies
    6
    Views
    1,192

    Just a FYI Update> Went to this job today and...

    Just a FYI Update>
    Went to this job today and the board is slowly fading into the sunset.
    I now have no access other than status, but, the good news is that when i was there yesterday I was able...
  21. Replies
    6
    Views
    1,192

    thanx for the response... before I get back over...

    thanx for the response...
    before I get back over there when I hit program does it normally prompt for
    for that password (cause this display currently does not) or when "program" is on the...
  22. Replies
    6
    Views
    1,192

    York YCAJ Millenium Can't Change FL Amps

    York Semi Hermetic YCAJ 0140 I can't change the full load amp settings The chiller starts and runs on both circuits but the chiller locks out on high current . when I hit the current button it...
  23. Johnson M3 graphics Set up button to display schedule

    I need someone in Johnson land for this. I have a m-3 Graphics GDF display
    I want to add a button to basically execute minspecter and then open up the schedule file for that piece of equipment...
  24. Replies
    153
    Views
    36,469

    in your email

    in your email
  25. Replies
    14
    Views
    1,658

    just saw that you have this 230.10.m1 info I was...

    just saw that you have this 230.10.m1 info I was looking for
    could I possibly trouble to send it to one more guy?? My email is Removed
    I have a ycas 160 that we put in a new compressor 2 years ago...
Results 1 to 25 of 39
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event