Search:

Type: Posts; User: #1servicetech

Page 1 of 18 1 2 3 4

Search: Search took 0.02 seconds.

  1. The upgrade is easy to get. the part number is...

    The upgrade is easy to get. the part number is LP-FX40UPG-0 I got one off of ebay ( FX20 ) about a year ago and just upgraded it 2 weeks ago. I should add that you need workbench to do the upgrade.
  2. Thread: Lon Plug

    by #1servicetech
    Replies
    12
    Views
    529

    Just to let everyone know, I found the part at...

    Just to let everyone know, I found the part at mouser. the part number is 14310214402000 and is made by Harting. the picture shown is the wrong one t but the part is correct.
  3. Replies
    1
    Views
    139

    Carrier 6400 controller problem

    I have a xl23 chiller with a carrier 6400 controller. I uploaded the program and was going to make a few changes. when I tried to click on controller to look at the setup, it was greyed out and...
  4. Thread: Lon Plug

    by #1servicetech
    Replies
    12
    Views
    529

    I think I found it on Mouser. I will post the...

    I think I found it on Mouser. I will post the part number if it is right. I went to the site you book marked and there is a 27.00 surcharge to cover the minimum.
  5. Thread: Lon Plug

    by #1servicetech
    Replies
    12
    Views
    529

    Thanks for the numbers. both sites don't show...

    Thanks for the numbers. both sites don't show anything online so I will give them a call tomorrow.
  6. Replies
    4
    Views
    303

    I would just use a MUX to put the setpoint or...

    I would just use a MUX to put the setpoint or input to a value that would make the pid go to 0
  7. Thread: Lon Plug

    by #1servicetech
    Replies
    12
    Views
    529

    I went to both sites and put in the numbers that...

    I went to both sites and put in the numbers that are on the plug but there are so many. does anyone have a part number?
  8. Thread: Lon Plug

    by #1servicetech
    Replies
    12
    Views
    529

    Lon Plug

    I have the lon usb adapter. The plug is getting a little worn and I sometimes have to adjust it to get communication. does anyone know where I can get a new plug for this? I am talking about the...
  9. Replies
    16
    Views
    1,780

    without the original disk you probably won't be...

    without the original disk you probably won't be able to reinstall it. did you have graphics? if you did you may be able to save those.
  10. I just read a previous response and you said you...

    I just read a previous response and you said you have the old hard drive in the new computer. did you release the authorization code from the old computer and reregister it?
  11. Is there an address written anywhere on the bcu?...

    Is there an address written anywhere on the bcu? if this is bacnet IP the workstation will need to be in the same subnet address range to connect.
  12. Are you using a crossover cable? you need a...

    Are you using a crossover cable? you need a crossover cable for the computer to bcu connection.
  13. Replies
    5
    Views
    312

    Thank you. I will give this a try.

    Thank you. I will give this a try.
  14. Replies
    5
    Views
    312

    Trane BCI-R problem

    Good morning all.
    I have a trane BCI-R that is giving me problems. I have a jace installed with the mstp license and I can see all of the points fine. I turned on BO1 which is supposed to enable...
  15. Replies
    7
    Views
    347

    The PC

    The PC
  16. Replies
    7
    Views
    347

    I just rechecked and you are right on both counts.

    I just rechecked and you are right on both counts.
  17. Replies
    7
    Views
    347

    I thought that might be the case. I have switched...

    I thought that might be the case. I have switched it all to a laptop with a modem for now and will upgrade it all as soon as possible.
  18. Replies
    7
    Views
    347

    old alerton TUX

    I have an old alerton tux system. it has an ISA card in the old computer which has died. it says IBM Lan card and has only 2 wires to a 25 pin rs232 type connector. is this an RS485 card? can I use a...
  19. yes, you would need to set up a VPN or use log me...

    yes, you would need to set up a VPN or use log me in.
  20. yes, it will work fine on a 64 bit computer. I am...

    yes, it will work fine on a 64 bit computer. I am running version 17 on a 64 bit win7 computer currently and it all runs fine. as was said before, you need the latest service packs.
  21. Replies
    1
    Views
    232

    Staefa Jace

    Does anyone have the staefa jace default platform password?
  22. Replies
    1
    Views
    341

    How are you starting them up? are you using the...

    How are you starting them up? are you using the run*.bat for them?
  23. Replies
    9
    Views
    1,283

    Could I get a copy of that also please?

    Could I get a copy of that also please?
  24. Replies
    3
    Views
    322

    If I remember correctly it would give you the...

    If I remember correctly it would give you the name and ask if you still want to log in using that name. have you gone into the setup and put the correct port number and baud rate? at the first screen...
  25. Replies
    3
    Views
    322

    Are you using PCLedit or PCMedit? what kind of...

    Are you using PCLedit or PCMedit? what kind of computer comm port are you using?
Results 1 to 25 of 436
Page 1 of 18 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event