Search:

Type: Posts; User: mrhvacmechanic

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    2
    Views
    535

    Did you ever get password? I need it also?

    Did you ever get password? I need it also?
  2. Thanks control! I noticed this cut says motor...

    Thanks control!

    I noticed this cut says motor has no end switches?
    The existing tower fan panel shows some sort of end switch. I'm wondering if they installed some type of whisker switch some...
  3. INVENSYS DURA DRIVE MA40-7170 DAMPER MOTOR

    120 Volts 150 lbs two position

    Would anyone have a cut on this damper motor?

    I have two of them on top of a fluid cooler for discharge dampers.

    I don't know if it has end switches? I...
  4. Replies
    35
    Views
    1,693

    Fee for re-certify is $90.00 and test is 50...

    Fee for re-certify is $90.00 and test is 50 questions. One of our techs just re-certified.
  5. Replies
    35
    Views
    1,693

    Took STAR in 2007. Its been around a while. They...

    Took STAR in 2007. Its been around a while. They want you to pay a fee every 5 years to update and recertify.
  6. Jer, Would you have the part number for the...

    Jer,
    Would you have the part number for the cable? Also is there a fee for the software or is it a free down load?
    I would like to give the info to my office.
  7. No current sensors of any kind. Just a flow...

    No current sensors of any kind. Just a flow switch connected to the pump panel. My guess is if pumps are in auto and flow switch opens, pumps change over. There are two red fault indicators on pump...
  8. SIEMENS PUMP PANEL with a LOGO 230RC

    Would anyone have the info on how to set up and check out this older model controller.
    The job was installed in 2005.

    The control operates two chilled water pumps. The panel has a flow switch...
  9. Replies
    89
    Views
    7,176

    When these MRI's loose power from a breaker trip,...

    When these MRI's loose power from a breaker trip, they just don't pop back on like nothing happened. Usually on a power loss the computers power down on a UPS system. After restore, system has to be...
  10. Replies
    45
    Views
    4,329

    These timers always bleed voltage thru them As...

    These timers always bleed voltage thru them As stated they operate on a current draw.

    In this case I use a Idec RTE series timer with base, instant close, time open.
  11. Replies
    4
    Views
    631

    I had never seen one before. I have seen in...

    I had never seen one before.

    I have seen in the past the Dx but didn't know you could hook up a screen to it.

    Thanks!
  12. Replies
    4
    Views
    631

    JOHNSON CONTROL

    Here is a picture of it.
  13. Replies
    4
    Views
    631

    JOHNSON CONTROL PAD

    Guys,
    I was doing maintenance on a roof today on a water tower. My partner whent down to the van to get some equipment we needed.

    While I was waiting for him, I saw some other equipment on the...
  14. Replies
    8
    Views
    841

    Could the first coil be a pre-heat? The the...

    Could the first coil be a pre-heat?
    The the others after the "Y" could be re-heats for two separate zones or areas with their own T stats?
    Do theses coils all have their own control valves?:)
  15. WIDOW UNIT CLEANING OF STYROFOAM DISCHAGE

    Just a quick question on cleaning the discharge of window units. I have five of them in my home. Three which I bought this season.

    No matter how clean I keep the intake filters, the styro....
  16. Replies
    4
    Views
    781

    Even worse when you have to go off road in the...

    Even worse when you have to go off road in the snow and the van isn't a 4 wheeler!
  17. Replies
    19
    Views
    1,571

    Could there be any evaporation loss due to valve...

    Could there be any evaporation loss due to valve packing & stems over a period of time?
  18. Replies
    34
    Views
    3,014

    I have used Staybrite since 1975, many times on...

    I have used Staybrite since 1975, many times on installing an access fitting. Have never had a problem. However, I usually use a1/8" or 1/4" copper access fitting.

    PSEMG prefers the #8. I usually...
  19. Replies
    31
    Views
    3,395

    Had a call no heat call last winter for a RTU...

    Had a call no heat call last winter for a RTU that fed a basement gymnasium. Another one of those COD's??

    Went up on roof, an found cover hanging by its screws and blown out from the unit??...
  20. BA, This I did know. My point was that I...

    BA,
    This I did know.
    My point was that I didn't think Emerson was still using the ALCO logo on the Emerson products.
    I figured this is an old vale on this unit??
    I do not know when Emerson...
  21. How old is this valve?? ALCO has been out of...

    How old is this valve?? ALCO has been out of business for a while if I'm not mistaken?
  22. Replies
    31
    Views
    3,395

    Turn off the unit and turn off the gas!! ...

    Turn off the unit and turn off the gas!!

    Write on your service ticket that the HXC has a hole or crack in it and it is defective. You turned off gas & power for safety reasons. Also state on...
  23. Replies
    9
    Views
    1,701

    I'm waiting for a set of step plates to come in....

    I'm waiting for a set of step plates to come in. Since I have about 20 bearings on a job to be replaced, they will make it easier.
  24. Replies
    9
    Views
    1,701

    I had looked into the step plates also. Seem kind...

    I had looked into the step plates also. Seem kind of expensive for a set of them.
  25. Replies
    35
    Views
    8,824

    New photo.

    New photo.
  26. Replies
    9
    Views
    1,701

    BEARING REMOVAL ON HOLLOW SHAFT TOOLS

    Hi, hope all are well.

    I have done allot of bearings over the years. However,sometimes I come across a bearing on a hollow shaft that needs to be removed with a puller??

    I can't always use a...
  27. Man that's bad!! Worst I have ever seen also.

    Man that's bad!!

    Worst I have ever seen also.
  28. Replies
    39
    Views
    4,805

    I live in NJ!! "THE LAND OF THE PROFESSIONAL RACE...

    I live in NJ!! "THE LAND OF THE PROFESSIONAL RACE CAR DRIVERS!!" That's what I call it!! No matter how fast you go or what lane you're in you get tailgated.
    The cops do nothing about it.

    I have...
  29. Handy, Would it pay to have a roof contractor...

    Handy,
    Would it pay to have a roof contractor look at the site??
  30. Replies
    39
    Views
    4,352

    Winter or summer, if your driving those kind of...

    Winter or summer, if your driving those kind of hours and not getting paid for it, find another company!! That's ridiculous!!

    Here in NYC its traveling time if its 25 miles or more from the shop...
  31. Replies
    5
    Views
    1,203

    Thank you both. Managed to track down a Johnson...

    Thank you both. Managed to track down a Johnson P70 with manual reset.
  32. Replies
    5
    Views
    1,203

    MANUAL RESET LOW PRESSURE SWITCH

    Gentlemen,

    Need a LP with manual reset??? Adjustable if possible? Range open about 40 psi??

    We need to protect system when Low Ambient time bypasses the existing control. System has lock out...
  33. Replies
    0
    Views
    535

    TEKTRA 905-01

    Hi guys!

    Was on a job Friday with this control which operated a small boiler.

    TEKTRA 905-01 ?? It looks like a Tekmar control but not spelled the same??

    I went to Tekmar site and...
  34. Replies
    65
    Views
    7,085

    I guess they just want you to change the filters...

    I guess they just want you to change the filters and belts in one hour. They want you off the job with out checking the rest of the unit!!

    Then a week later when a service call comes in on the...
  35. Replies
    20
    Views
    2,475

    Some bid low and when they get it, they do as...

    Some bid low and when they get it, they do as little as possible.
  36. Replies
    2
    Views
    1,273

    Good question MH! I installed one the other day...

    Good question MH! I installed one the other day but it came with no info?? If anyone has a cut sheet on this moder please attach it for us?:angel::angel:
  37. Thanks Wolfdog! Its a closed glycol loop. ...

    Thanks Wolfdog!

    Its a closed glycol loop. Condenser coil is spotless!:toetap:
  38. CARRIER AQUA SNAP CHILLER AUTO RESET ALARMS

    Went to job today, and chiller had two alarms: 301 & 302 strainer and condenser coil maintenance.

    Manual says: these alarms are auto reset, not manual reset??

    Question 1) Does anyone know...
  39. Replies
    1
    Views
    502

    STULS 4 TON TEV REMOVAL

    Correct me if I'm wrong??
    In order to replace a TEV on this unit, do you have to cut both the suction and LL and then lift out the "A" coil to do this???

    It seems the cross-member of the...
  40. "D", We checked fan on vsd to see if it was...

    "D",
    We checked fan on vsd to see if it was failing causing a rise in dis press..

    Factory said the unloaders stick some times until oil works into the seals??? Keeping comp unloaded with a rise...
  41. LIBERT DIG SCRL DISCHGE TEMP SENSOR ALARM W/VSD COND FAN

    Having a problem with a Libert digital scroll discharge temp sensor??

    It's been very cold here in NYC and condenser is running on VSD. The two other fans come on above 60*F. New unit,running with...
  42. Replies
    15
    Views
    2,830

    Valdelocc makes a good point. Most companies fill...

    Valdelocc makes a good point. Most companies fill the system and forget about them. Glycol levels have to be checked, they also can become corrosive! This happens if the alkalinity changes. Seed a...
  43. Replies
    8
    Views
    1,770

    Another way for the city to make a buck!!

    Another way for the city to make a buck!!
  44. Replies
    15
    Views
    2,414

    I always will install them. :patriot: Sometime...

    I always will install them.

    :patriot: Sometime 75*F won't keep liquid from collecting in the crankcase.

    May I ask what type of compressor are you working on that you have to recover the charge...
  45. Replies
    0
    Views
    494

    STULZ E2 SERIES TOUCH PAD

    Gentlemen,
    Just picked up an account for maintenance. The tenant used to have five floors and moved out. The five floors have been leased to other companies.
    The one we have took two floors and...
  46. Thank you P 10. I was just checking some othe...

    Thank you P 10. I was just checking some othe manuals I have for a 2004 unit. Both limits in series. If either breaks gives you a "4" flash of the green LED.

    Thanks for you time! Mr HVAC
  47. TRANE YCH180 IGNITION BOARD FAILURE CODES

    Would any one have the codes for the flashing led on the ignition board. No info on the unit 2004 install.

    Roof top nat gas . Went to trane site, no help. Getting four green flashes
  48. Replies
    14
    Views
    2,165

    The cover that blew off was the side access panel...

    The cover that blew off was the side access panel to the compressors and electrical. Gas line enters thru same cover and so does the combustion exhaust. Also the cover which slides out protecting the...
  49. Replies
    14
    Views
    2,165

    WRONG WAY TO FIX CRACKS IN HTXCR

    Found covers blown off a Carrier roof top when we arrived on a no heat call?
  50. Replies
    6
    Views
    1,231

    Get the ICM or Americian Tech speed controls....

    Get the ICM or Americian Tech speed controls. Good for both sleeve and bearing.
Results 1 to 50 of 1000
Page 1 of 20 1 2 3 4

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Quality Home Comfort Awards