Search:

Type: Posts; User: Bseliger

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    34
    Views
    5,487

    I was told to do this once, I called the service...

    I was told to do this once, I called the service advisor at gustave a Larsen, he told me that is not an approved way to clean a coil
  2. Replies
    71
    Views
    6,165

    You won't regret the veto!

    You won't regret the veto!
  3. Replies
    17
    Views
    2,208

    You can tell the foam fell out of the roof truss...

    You can tell the foam fell out of the roof truss cavity, it must have been damp and the foam just dropped instead of grabbing the wood
  4. Replies
    25
    Views
    2,805

    Not exactly how you recover ammonia, lol , but it...

    Not exactly how you recover ammonia, lol , but it makes it safe to dump down the drain per say. 6" bubble? How bad are hot rodding that drain down
  5. Thread: Trane voyager

    by Bseliger
    Replies
    18
    Views
    1,159

    I have a bosch pocket impact that works great on...

    I have a bosch pocket impact that works great on those screws. Let it rap a couple times real slow and they usually bust free.

    - - - Updated - - -

    I've never heard of using the amp draw, ill...
  6. Thread: Trane voyager

    by Bseliger
    Replies
    18
    Views
    1,159

    According to the rep at Larsen they were out of...

    According to the rep at Larsen they were out of range. Where did you get your info from? Im more worried about getting things done right than my ego
  7. Thread: Trane voyager

    by Bseliger
    Replies
    18
    Views
    1,159

    I was more curious if different igniters had...

    I was more curious if different igniters had different ohm ratings. I know the 80 volt ign are lower than the 120 volt.
  8. Thread: Trane voyager

    by Bseliger
    Replies
    18
    Views
    1,159

    One of the reps from gustave Larsen finally got...

    One of the reps from gustave Larsen finally got back to me. Per the rep he said anything over 80 has the potential to fail and should be replaced.... I'll stick to my 100-110 range
  9. Thread: Trane voyager

    by Bseliger
    Replies
    18
    Views
    1,159

    I've tried finding specs, anyone have any idea...

    I've tried finding specs, anyone have any idea where they can be found.
  10. Thread: Trane voyager

    by Bseliger
    Replies
    18
    Views
    1,159

    Trane voyager

    Just curious what everyone does as far as replacement for hot surface igniters. Usually I try to replace them when they get around 100-110 ohms. Have a couple units that are at 140 and 170 ohms. I'm...
  11. Thread: Time sheets

    by Bseliger
    Replies
    2
    Views
    366

    Time sheets

    Company recently got iPad minis for billing. I was wondering what billing programs do most of you guys use and if there were any good apps for time sheets. Any tips on keeping info on individual...
  12. Thread: york 30 ton

    by Bseliger
    Replies
    2
    Views
    245

    I thought of that, but the evap manifold gets...

    I thought of that, but the evap manifold gets cold when it does run
  13. Thread: york 30 ton

    by Bseliger
    Replies
    2
    Views
    245

    york 30 ton

    York Model Y13AC04A2AAAABC Serial S NDLM030707 R-22. Unit has 3 coils in this setup /\/. Far Right is compressor 1 coil, middle is compressor 3 coil and Far left is Compressor 2 coil. Compressors...
  14. Replies
    16
    Views
    877

    Im guessing by cooling the tank your getting it...

    Im guessing by cooling the tank your getting it closer to becoming a liquid inside the tank and making it easier to dump more refrig inside?
  15. Replies
    25
    Views
    1,684

    I have a set, haven't used them a ton. Mine came...

    I have a set, haven't used them a ton. Mine came with regular hoses, have to find a set with ball valves. That's my only complaint so far
  16. Replies
    101
    Views
    3,502

    if you wanna know if your cap tube is plugged...

    if you wanna know if your cap tube is plugged look for frost..... The refrigerant will release its pressure and the temp of the refrig will drop inside of the cap tube. Think a mini cap tube inside...
  17. Replies
    27
    Views
    963

    I would check to make sure you have 24 volts at...

    I would check to make sure you have 24 volts at the contactor. If not then you need to go back to the board on the furnace. If you do have 24 volts at the coil, push the contactor in. Do you have 240...
  18. Thread: Brutal!!!!

    by Bseliger
    Replies
    74
    Views
    3,908

    I believe they justify using a drier that small...

    I believe they justify using a drier that small because they unit and should not have a lot of junk in the system until its run for alota hours.... i believe the units call for a bigger drier when...
  19. Thread: Ameristar

    by Bseliger
    Replies
    4
    Views
    365

    Ameristar

    Anyone have any experience with these furnaces or ac units? overall value, quality or problems?
  20. Replies
    2
    Views
    223

    I believe if you click on forum and then go down,...

    I believe if you click on forum and then go down, there is a section that says how to join followed by several pro sections.
  21. Replies
    39
    Views
    1,696

    I appreciate the help and everyones input, and im...

    I appreciate the help and everyones input, and im sure everyone on this forum has been at the point where they have been in the sun all day, got home feeling beaten down because your lost and looking...
  22. Replies
    39
    Views
    1,696

    This unit was ran for three years with it...

    This unit was ran for three years with it intermittent tripping breaker... at this point its at every 3 hrs when I was called. It was murdered
  23. Replies
    39
    Views
    1,696

    One lead to ground, one lead to the start...

    One lead to ground, one lead to the start winding.also the unit has a scroll
  24. Replies
    39
    Views
    1,696

    The merger lit up the first light which is...

    The merger lit up the first light which is twenty....
  25. Replies
    39
    Views
    1,696

    I came to this site because I know alota guys...

    I came to this site because I know alota guys know a lot more about this and I don't feel like ****ing the home owner over. How bout a little more help versus trying to put someone down. After all if...
Results 1 to 25 of 117
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event