Search:

Type: Posts; User: The Dog

Search: Search took 0.00 seconds.

  1. Replies
    15
    Views
    1,552

    Critical Room Control Have used quite a few with...

    Critical Room Control
    Have used quite a few with great results in multiple hospital environments.

    http://www.criticalroom.com/
  2. Replies
    4
    Views
    615

    2 DOs: I would Link a Start/Stop block into the...

    2 DOs: I would Link a Start/Stop block into the 'or' of 2 logic blocks. Set the 2nd logic 'or' as 'not'. Logic outputs to DOs. Proxy out the start/stop as nvimanocc. This should be the easiest...
  3. Replies
    4
    Views
    615

    Do you mean a manual over-ride of a hardware...

    Do you mean a manual over-ride of a hardware output?
    Simplest way: connect a Setpoint to a logic block - logic block to an output. Proxy out the setpoint to AX. Write to your setpoint thru AX. ...
  4. Replies
    5
    Views
    1,247

    Configure your hardware point AI in the 15C as...

    Configure your hardware point AI in the 15C as 'Outside air Temp' and download the controller. In Distech, drop an nvi point on your programming wiresheet and name it 'nviOaTemp' or whatever you...
  5. Thread: Lon Bindings

    by The Dog
    Replies
    3
    Views
    766

    They will only show up in the Link Manager if...

    They will only show up in the Link Manager if they are actual Lon Links - you have to link from controller to controller, not proxy point to proxy point. If done correctly, the links will show on...
  6. Thread: Tschüss

    by The Dog
    Replies
    13
    Views
    1,834

    Now what did he say?!?! I must have missed sumpin

    Now what did he say?!?! I must have missed sumpin
  7. Thread: smart controls

    by The Dog
    Replies
    11
    Views
    1,729

    Hopefully no one in your area is already a...

    Hopefully no one in your area is already a dealer, they won't sell in my area as another contractor already has my territory.
  8. Thread: smart controls

    by The Dog
    Replies
    11
    Views
    1,729

    try here: http://diviotech.com/

    try here: http://diviotech.com/
  9. Replies
    7
    Views
    845

    I just did it with my laptop through a browser,...

    I just did it with my laptop through a browser, but I have the plug-ins loaded on my machine.
    Just tried it with another office computer without workbench or the plugins and could not do it. I...
  10. Thread: AX Plug Ins

    by The Dog
    Replies
    8
    Views
    709

    Distech does: fully programmable, application...

    Distech does: fully programmable, application specific, and I/O modules. I like 'em!
  11. Thread: JACE 200

    by The Dog
    Replies
    13
    Views
    1,878

    SomeOldGuy - are/were you planning on using the...

    SomeOldGuy - are/were you planning on using the I/O 34 for controlling the VAV boxes? I would suggest using a lon VAV controller for each vav box. Which means that you need to buy the lon driver...
  12. Replies
    8
    Views
    654

    Are all the needed modules loaded on the...

    Are all the needed modules loaded on the supervisor machine?
  13. Replies
    3
    Views
    595

    Thanks. Further research revealed that Siemens...

    Thanks.

    Further research revealed that Siemens has their own apogee to net 8000 driver. Looks like they go rs-485 to rs-232 to the GCM. good news for me.

    Again, thanks for the info.
  14. Replies
    3
    Views
    595

    Siemens and Network 8000 GCM

    DOes anyone know how Siemens would take over an Invyensys Network 8000 GCM? Do they comm to the GCM and leave it in place or do they remove the GCM and communicate on the ASD wire? Local branch is...
  15. Replies
    0
    Views
    377

    JCI 'XFT' System

    Anyone ever hear of a 'JCI XFT Control System Headend'? Is it an old branch thingy? Is there any way to bring this 'system inta an FX60?
  16. Thread: i quit

    by The Dog
    Replies
    28
    Views
    2,237

    9 months ago, I did the exact thing you have just...

    9 months ago, I did the exact thing you have just done. Probably the best move in my life, besides getting married. Don't be fooled, some things will be tough, it ain't going to be all gravy. ...
  17. Replies
    5
    Views
    738

    Jogas, Check your gmail, I couldn't attach here -...

    Jogas, Check your gmail, I couldn't attach here - to big and to lazy. Feel free to distribute here.
  18. Replies
    6
    Views
    521

    Even the XL500 is being replaced with the XL800. ...

    Even the XL500 is being replaced with the XL800. You can still buy some 500 parts, but once they are gone - no more.
  19. Replies
    6
    Views
    521

    I'm not sure if it being phased out (probably?),...

    I'm not sure if it being phased out (probably?), but it is definitely C-bus only - the last I heard from my Honeywell supplier.
  20. If you are not using Tridium, then Distech is...

    If you are not using Tridium, then Distech is your only choice. Spiders can only be programmed in the Tridium AX environment. Distech has free LNS plugins and Tridium plugins.
  21. Replies
    4
    Views
    541

    will the station run on your laptop? What does...

    will the station run on your laptop?
    What does the standard output say? the error most likely will show up there.

    If it doesn't, save a backup of the station somewhere, open the station offline...
  22. Replies
    11
    Views
    1,277

    Just thought of another item. I believe that the...

    Just thought of another item. I believe that the Jace has to be the end of the line of the near side (other end of the router)of the LonNetwork, but I could be mistaken.
  23. Replies
    11
    Views
    1,277

    "After the LON router is added using the external...

    "After the LON router is added using the external network mgmt tool, does the JACE Device need to "discover", or "learn" the network to "find" the LON router?"

    OK, I just saw this. You need to go...
  24. Replies
    11
    Views
    1,277

    Unless I am reading this wrong, you will need to...

    Unless I am reading this wrong, you will need to put the router in "temporary repeater' (the term may not be exactly right) mode and commission the controllers for subnet 6 and then put the router...
  25. Replies
    3
    Views
    653

    there is a decent company in Grand Rapids , MI...

    there is a decent company in Grand Rapids , MI looking. They had an ad sitting on the counter in the supply house. Call Cochrane supply in GR, they will point you in the right direction.
  26. Thread: The TRUTH!

    by The Dog
    Replies
    7
    Views
    1,046

    so TRUE!!

    so TRUE!!
  27. Replies
    24
    Views
    1,572

    Did you upgrade the Jace or are you talking about...

    Did you upgrade the Jace or are you talking about upgrading your laptop?
    If you upgraded the JACE with no liscence upgrade, you are 'hooped' until you get an upgraded liscense.
    If you are talking...
  28. Replies
    35
    Views
    2,412

    Poll: Mainly stay with partners, but will go to...

    Mainly stay with partners, but will go to KELE,ALPS,Veris.... to get what I want
  29. Thread: R2 Questions

    by The Dog
    Replies
    4
    Views
    700

    I believe an 'orange' shadow object means that...

    I believe an 'orange' shadow object means that the controller database and the Jace database do not match. I would go to the properties shaeet of the shadow object and upload the current controller...
  30. Thread: Smart Controls

    by The Dog
    Replies
    5
    Views
    1,263

    I believe Smart Controls has limited the software...

    I believe Smart Controls has limited the software to authorized dealers only, i.e. you must sign up to be a dealer. Call them to find out. If you know Neuron C code, I think you can download that...
  31. Replies
    6
    Views
    1,504

    on the one I have connected to it was: tridium:...

    on the one I have connected to it was: tridium: niagara .although it has a Beta license, so it may be altogether different
  32. Replies
    7
    Views
    1,151

    This is more than just a sensor, so it might be...

    This is more than just a sensor, so it might be more than you are looking for

    http://distech-controls.com/DISTECH_2004/ENG/PRODUCTS/lonmark_thermostats.htm
  33. Replies
    2
    Views
    646

    What brand of controller is it? Most...

    What brand of controller is it? Most manufacturers literature has the enumeration converters in them.

    If it is a hexidecimal #, pull up your calculator on your laptop, click on 'view'
    and click...
  34. I have one site that I can't use Firefox as...

    I have one site that I can't use Firefox as browser, only Internet Explorer. We used HTML and in the code it only accepts IE. Don't know if we wrote that in there or if it codes automatically when...
  35. Replies
    32
    Views
    8,568

    I have a Jace 4 with extended memory with 40...

    I have a Jace 4 with extended memory with 40 spyders (Vav App), 4 15cs and 22 XL10 vav. the jace is working all right, just have to be careful when in workbench so as not to put the CPU at 100%.
  36. Replies
    11
    Views
    916

    Why not buy a LON remote IO device that has a...

    Why not buy a LON remote IO device that has a active v/ma configurable input. You could do it yourself and save customer money and you wouldn't be tied to another contractor to get it done?
  37. Did you try using a Dynamic Device shadow object...

    Did you try using a Dynamic Device shadow object instead of the Microtech shadow object? the Dynamic Device should learn the new SNVTs
  38. Replies
    24
    Views
    2,961

    I believe the 403 has a lon node limit of 27,...

    I believe the 403 has a lon node limit of 27, unless you get the extended node version, which makes the lon node limit 120??
  39. Replies
    3
    Views
    2,173

    try this link...

    try this link
    http://www.commercial.carrier.com/commercial/hvac/product_technical_literature/1,3069,CLI1_DIV12_ETI4906_PRD1122,00.html
  40. Replies
    10
    Views
    2,245

    Sys, the carrier tech set it up on the CCN side...

    Sys, the carrier tech set it up on the CCN side when I wasn't there. It doesn't make sense to provide the snvt and not have it control anything
  41. Replies
    10
    Views
    2,245

    You can only command Chiller on (SNVT_switch) and...

    You can only command Chiller on (SNVT_switch) and give it a setpt (SNVT_Temp_P), and a capacity limit. It shows an nviOccSchedule but when I linked it up, it controls nothing. I also found that the...
  42. Thread: Smart Controls

    by The Dog
    Replies
    4
    Views
    928

    Not certified because most of their products are...

    Not certified because most of their products are fully programmable - you have to make them conform. They are programmed with either code or with a graphical programming tool that is fairly easy to...
  43. Replies
    13
    Views
    2,252

    II use a wooden TV Dinner stand for the laptop...

    II use a wooden TV Dinner stand for the laptop and a fold up chair (camping style). Both have shoulder straps affixed for long walks to mechanical rooms. I was tired of the buckets and pipe...
  44. Replies
    5
    Views
    660

    I have had only one bad ML7295 actuator, but I...

    I have had only one bad ML7295 actuator, but I think it stemmed from someone trying to use the manual lock thingy. That little plastic (junk) philips head was stripped out and half pushed in. Sure...
Results 1 to 44 of 45
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event