Search:

Type: Posts; User: Gerbs1983

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    241

    Camera suggestions...

    In your opinion, what is the best 'probe' camera to have on the truck...for checking tight spots, heat exchangers, etc? I have a rigid that I'm not that impressed with.
  2. Replies
    37
    Views
    1,462

    Agreed - caps are easy to diagnose quickly, and a...

    Agreed - caps are easy to diagnose quickly, and a bad cap doesn't mean something else is wrong - a lot of things could be wrong that are totally unrelated. I also agree that we can't offer free PM's...
  3. Replies
    37
    Views
    1,462

    That type of advertisement cannot be bought...and...

    That type of advertisement cannot be bought...and is by far the most effective!
  4. Replies
    37
    Views
    1,462

    Ever seen a new install, especially one not done...

    Ever seen a new install, especially one not done by your company, that had insufficient ductwork, mismatched equipment, incorrect charge? I think a bad 1 yr old cap is a red flag...

    That being...
  5. Replies
    37
    Views
    1,462

    We all conduct business a little differently,...

    We all conduct business a little differently, agreed...as long as they are legal...agreed! Our company has driven this into our heads "We don't change the quality of service (checking the things...
  6. Replies
    37
    Views
    1,462

    If the customer would benefit from any of...

    If the customer would benefit from any of these...refrigerant, contactor, coil cleaning, etc...don't you think it's our responsibility to bring this to their attention? If we don't, who will? Again,...
  7. Replies
    37
    Views
    1,462

    It's obvious that you are a very experienced...

    It's obvious that you are a very experienced tech, but this post is concerning to me. Is it good practice to just throw a part on and fire up a unit without checking some amp draws, pressures,...
  8. Replies
    11
    Views
    365

    Looking to learn...

    I'm continually amazed at how some of the experienced guys on here can troubleshoot a problem based on the info someone else in providing...thank you for sharing your knowledge!

    There are a...
  9. Replies
    56
    Views
    5,507

    Guess this needs to be added to the list of...

    Guess this needs to be added to the list of questions when troubleshooting on here:
    What's your subcooling and superheat?
    What's your out door temp?
    What's your temp drop?
    Is your ac installed...
  10. Replies
    23
    Views
    1,485

    What is this stuff???

    Heil furnace, 2008 model. Downflow, installed in 2009 as a replacement by another company. In mech room off of the garage. Natural gas.
    M# H9MPD075F12C2
    S# A082358717

    Inducer was locked up....
  11. Replies
    570
    Views
    96,282

    Didn't the missing coil and lineset give it away?

    Didn't the missing coil and lineset give it away?
  12. Replies
    4
    Views
    556

    Manual was not available, and, not being Lennox...

    Manual was not available, and, not being Lennox dealers, we have a hard time getting help or info from them. This was after hours and tech support was closed. I was busy on a call next available day,...
  13. What is the flame sensor reading?

    What is the flame sensor reading?
  14. Replies
    4
    Views
    556

    Lennox pressure switch issue

    Lennox M# G43UF-36B-070-09
    Pressure switch keeps dropping out. There are two hoses to this particular switch, red and black. The red is the main pressure switch hose, measuring -2.5"WC consistently....
  15. Replies
    4
    Views
    528

    Thanks for the info guys! I also talked to Bryant...

    Thanks for the info guys! I also talked to Bryant tech support and was told that putting the screws in the burners almost always takes care of the issue. I need to make sure we have the right screws...
  16. Replies
    7
    Views
    480

    The black receptacle behind that metal plate is...

    The black receptacle behind that metal plate is cracked. Before you replace that though, check the secondary behind it...that is most likely cracked as well and will require a new heat exchanger.
  17. Replies
    29
    Views
    1,497

    I'm not sure when a company is considered 'big...

    I'm not sure when a company is considered 'big and bad' - I have only worked for one, 8 yrs and counting. Started in new construction when there were 6 guys and the owner was out installing with us,...
  18. Replies
    4
    Views
    528

    Flame running back to orifice

    Bryant M# 312AAV036070ACJA S# 1906A19772

    Had been switched over to LP at installation by a previous company. They did the springs and orifices, but did not install the low gas pressure switch or...
  19. Replies
    29
    Views
    1,497

    That's a good point, and I agree, being truthful...

    That's a good point, and I agree, being truthful and very thorough is one thing - recommending repairs that aren't needed at all quite another.

    I'm interested in what the OP meant by saying he...
  20. Replies
    29
    Views
    1,497

    I would not want to work for a company that...

    I would not want to work for a company that pressured me to 'push' a system if it wasn't in the best interest of the homeowner. I also wouldn't want to be expected to sell or reccomend anything that...
  21. Replies
    15
    Views
    1,296

    I recently went from a full size van to a...

    I recently went from a full size van to a transit. I had to leave some things behind, but so far it has worked out really well (it's only been this heating season so far). I have a box of filters...
  22. Replies
    13
    Views
    1,220

    Unless this was a supercede, that was most likely...

    Unless this was a supercede, that was most likely NOT a good idea....
  23. Replies
    21
    Views
    1,365

    Agreed. It was over the phone, I told her we...

    Agreed. It was over the phone, I told her we would need to look at it. She informed me of her homeowners insurance and I quickly and politely informed her it would not be us coming out.
  24. Replies
    21
    Views
    1,365

    Hunter thermostat

    Lady called in wondering what the bP flashing on her hunter thermostat meant. I have had no luck finding any info on these stats. Anybody have any ideas?
  25. Replies
    38
    Views
    4,314

    True, on this particular Trane, the board...

    True, on this particular Trane, the board controlled gas valve on its own mini circuit, per the 12 pin plug.
Results 1 to 25 of 32
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event