I saw it driving down the road had to stop and get a pic. The house is sitting empty, it's a foreclosure .
Type: Posts; User: HPpro
I saw it driving down the road had to stop and get a pic. The house is sitting empty, it's a foreclosure .
It was really hard to tell, EVERYTHING was burnt. The indoor filter was a spaceguard 2200 under the air hander, it hadnt been changed in a few years and was PLUGGED! It happened on a warmer evening...
Judging by the way the grass looked I dont think the lawn guys did this
http://img84.imageshack.us/img84/8530/10110615431.jpg
http://img155.imageshack.us/img155/284/10110615441.jpg
...
Found this a few months back, it was right at the end of the heating season. Customer called and said he had a little problem with his outdoor unit, I walked around the corner and saw that i had to...
Surprised the tank isnt leaking on that thing yet. Does Lennox still give customers a credit on new equipment if the tank fails on those?
What exactly is shutting down? Im guessing from what your saying its just the compressor? Is there a TXV on the indoor unit, maybe its a possibility on a long run cycle your super heat is rising...
Light heat is key!
Light heat is key!
Thats just sorry worksman ship. The grass will be greener on the other side for sure in this case. The worst thing about that is you get put in the situation where eventually some customers are...
Wow, that looks horrible. Who would run screws into someones window frame? I guess "They thought it looked better" if they ran the condensate line in one direction and the lineset in the other.
Could you try unhooking the electric heat just to eliminate that as a possibility?
Usually the modules on the motors fail, and its a lot less to replace just the module. Pick up a tester for the motors, they hook to 24 volts and to the motor and it will allow you to test the...
Thats the "weed eater protection kit" those are extra on installs!
Ive never had any problems with a 410 system that you couldnt have with a R22 system. Been installing and servicing them since they first became available.
Dont think i ever heard a motor sitting idle humming, did you try unhooking the motor leads just to make sure that was indeed making the noise?
lol, was there any on the threads??
Ha! Looks like it just slides right on out!
Sounds like it, toggle between modes (Heating & Cooling) and see if you can hear your reversing valve move
Ok so on a gas furnace the board is controling the blower. Dependent on which stage its in. Agreed? Thats all I stated. The control controls the blower, the original question asked about jumping...
Yes you do have to tell the control board the stages of the thermostat, even if you have a 2 stage thermostat the control board still controls the blower in the heating mode. You also have to tell...
I think he meant hydronic coil in the air handler. (hot water forced air heating) you said earlier it was a "hydro" unit. If that coil is impacted in any way that could effect air flow across the...
Refrigerant returning on the suction line cools the compressor, if you starving your evaporator your not returning the proper volume of vapor refrigerant and that will over heat a compressor and at...
is the compressor running when you have those readings? If so those arent stabilzed pressures, that is your pressure differential your running compressor is creating. If you took super heat and sub...
they ask for O as well so the AHU will know to go the set cooling speed, not the set heating speed when the AHU is used on a cooling only installation.
I had to read it a few times but thats what i got out of it. The question was "ever have this happen" and the rest was describing the scenario. I guess the guage sealed to the suction line port and...
Out of all three of those being at the same price I would have to take the american standard. My personal opinion. They have some nice equipment in various product lines.
If its a gas furnace the blower operation is controlled via the control board for the heating mode, if its a air handler the y call is still controlling the blower speed for heating mode
Super heat and sub cooling will tell you whats going on in the system....
they were probably afraid to touch anything after they got done putting that mess together and it worked.
Forget teaching them how to do duct sizing some one should teach them how to use snips first.
lol, its his exwifes house.
Ive seen people try to squeeze a bulb on a TXV that was "stuck open" but that doesnt even have tool marks on it.
Great Work! At least they didnt screw the boards down into the coil!
Good looking work, do you have any problems with the a/c draining with the furnace pitched forward like it should be and the evaporator coil facing back?
The only place a trap belongs in a hvac drain line is if the drain is on the negitave side of the blower. This is done to allow proper drainage of the system if is not insalled your blower will hold...