Search:

Type: Posts; User: chilly123

Page 1 of 7 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    79
    Views
    4,850

    I have been a market tech for the last 27yrs, and...

    I have been a market tech for the last 27yrs, and don't plan on giving up anytime soon.:)
  2. coldkeeper if you have a model # of this unit. my...

    coldkeeper if you have a model # of this unit. my experience with dual temps have been with the m1ge cases. as far as factory setup, don't bet on it:D
  3. Replies
    23
    Views
    1,402

    What frustrates a customer?

    Two things on my end of the world. 1st repeat calls, I seem to gain more customers this way than anything else. 2nd the energy guys that come around every 6mons or so. everytime they make changes to...
  4. Replies
    11
    Views
    1,201

    Were these Bridgeton cases or Mexico ? Its nice...

    Were these Bridgeton cases or Mexico ? Its nice to see I have company on these POS. ever since IR bought hussman the quality is gone.:(
  5. Replies
    11
    Views
    1,201

    Haven't had too many problems with frame heaters,...

    Haven't had too many problems with frame heaters, but have had allot of problems with the doors themselves, not keeping tension. had one store with 35 doors replaced under warranty.
  6. Replies
    2
    Views
    792

    I would certainly go for the drain pan heater. I...

    I would certainly go for the drain pan heater. I have several markets with these cases. All electric defrost, a year after they were installed the drain pans were iceing up. My company has been...
  7. Replies
    6
    Views
    1,269

    groogy1 try getting a little more info in your...

    groogy1 try getting a little more info in your profile. they are DYI's that try this on here. We need to know are you a mechanic, owner. This is our lively hood, DYI's are not taken too kindly here....
  8. Replies
    22
    Views
    2,313

    congrats Mikey on your first year in the markets....

    congrats Mikey on your first year in the markets. my self I have been at it since 1982, and still enjoy it everyday. may you have a long and prosperous career
  9. Replies
    19
    Views
    1,814

    Hmmm sounds very familiar to me. +1

    Hmmm sounds very familiar to me. +1
  10. as slatts stated this info is critical to know....

    as slatts stated this info is critical to know. in addition to check the condition of the contactor or mag starter. if burnt this will cause a single phase condition. if its temp he is concerned...
  11. Well first off what kind of failures is he...

    Well first off what kind of failures is he having? Are these electrical or mechanical? More info is needed. like are these failures on the low temp or midtemp, discharge temps and pressures, suction...
  12. Replies
    13
    Views
    1,378

    Crackertech it just seems like they always want...

    Crackertech it just seems like they always want to take the easy way out. as many times as this subject has come up on this site they just don't get it, as rayr says only two things belong in a...
  13. Thread: Red dye test

    by chilly123
    Replies
    17
    Views
    1,346

    +1

    +1
  14. Replies
    1
    Views
    353

    mikey sq

    try this hussmann model Z reach -in i/c Evap temp -40 Discharge air -10 Btu's per ft 1270, model Z reach -in low temp , evap temp -40 discharge air temp 0 btu's per ft 799. also look at the txv size...
  15. Replies
    16
    Views
    1,102

    DOA's

    A few years back i remember having changed out three caryles o6e comps on a rack. originals fried due to bad contact on the mag starters. Installed all three and went to start them up, open windings...
  16. Replies
    2
    Views
    415

    well there is not much difference than what you...

    well there is not much difference than what you have been working on now. you may see some differences in control set up. There are more self contained units in a c-store. You just have to like...
  17. Replies
    8
    Views
    666

    this was very intuitive on your part to mention...

    this was very intuitive on your part to mention the lack of electric safety's. A blood bank is the last place you EVER want to see some thing go down. this is something that makes the five o clock...
  18. Replies
    22
    Views
    1,451

    What he said, just use the pressure ctrl as a...

    What he said, just use the pressure ctrl as a loss of charge safety. as icemister stated you will get much better control of the box temp as well as a few less headaces:)
  19. Replies
    5
    Views
    1,252

    yotaman16 this is called plausible deny ability,...

    yotaman16 this is called plausible deny ability, standard Hussmann response:rolleyes:
  20. Replies
    18
    Views
    3,128

    May his house be strong! Thanks Andy:)

    May his house be strong! Thanks Andy:)
  21. Replies
    3
    Views
    418

    your doing it now. how long since installation? a...

    your doing it now. how long since installation? a bad install always creates problems like this. R-404 is a great solvent, any junk in the line from install will get to the driers and valves.:( I...
  22. Replies
    10
    Views
    707

    Just as crackertech stated. change oil filters...

    Just as crackertech stated. change oil filters and cores again then retest.
  23. Replies
    18
    Views
    1,053

    floodback

    Jaybee take a look at your case and any walkins that are on the loop first. this will help you narrow it down. the system that is struggling to maintain temp will be the one thats giving you the...
  24. Replies
    21
    Views
    1,473

    sounds like to me they got a great deal. :) and...

    sounds like to me they got a great deal. :) and you also got a great learn experience. myself i have had some fairly large invoices. the last one was 35 hrs on hussmann Rl case lighting:(
  25. Replies
    21
    Views
    1,073

    jaybee if your hitting your low limit at 10 psi,...

    jaybee if your hitting your low limit at 10 psi, you maybe loosing your power through the I/O relays. is comtrol showing any power failures? the line voltage for the solenoids that go through the I/O...
Results 1 to 25 of 172
Page 1 of 7 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event