Search:

Type: Posts; User: xpuser357

Page 1 of 15 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    27
    Views
    1,883

    Lol on losing tools, I still cannot find my...

    Lol on losing tools, I still cannot find my $40.00 duracell flash light. 12 volt impact driver works great and light to take screws out of cases and package units or where ever you have more than one...
  2. Pretty nasty Looks like fan shroud is just as...

    Pretty nasty Looks like fan shroud is just as bad. I use trash bags and silver tape, open up power box and wrap all with plastic then coil cleaner and water hose followed with shop vac. Tape is to...
  3. Replies
    61
    Views
    3,663

    You get what you pay for. That said I buy...

    You get what you pay for. That said I buy dependable tools, They may cost more but when you need to perform a task you do not want to have tool mar up device or strip a bolt or screw because it was...
  4. I lived in California where I acquired my first...

    I lived in California where I acquired my first hand gun 357 Magnum. Before I purchased it I saw two people coming out of a market/liquor store, they were shot and killed by driveby. Gang related,...
  5. Replies
    615
    Views
    108,801

    Went on a call awhile back at a old folks home,...

    Went on a call awhile back at a old folks home, Scotsman flaker ice machine not working. I arrive and see machine disassembled down to gear case is showing grease and water. Maintenance man took it...
  6. Replies
    615
    Views
    108,801

    Our company installed a duel fuel system, A year...

    Our company installed a duel fuel system, A year later Lightning struck condenser. I received service call they had no heat. When I arrived found Compressor shorted and wiring cooked. Went inside to...
  7. Replies
    13
    Views
    1,228

    unless you have isolating valves Yes you need to...

    unless you have isolating valves Yes you need to pump it down.
  8. Thread: Cheater cord

    by xpuser357
    Replies
    17
    Views
    1,943

    20 years ago I had to change compressor at a...

    20 years ago I had to change compressor at a drive in movie theater. They was closed I was there alone So I hooked up radio to listen to the Jams while working. Turned on switch and watched it smoke!...
  9. Links to direct purchase sites are not permitted...

    Links to direct purchase sites are not permitted in he open forums.
  10. Thread: Water Leak

    by xpuser357
    Replies
    11
    Views
    774

    Normally it is a slightly dirty coil, Water...

    Normally it is a slightly dirty coil, Water slides down to pan, when you have obstructions on surface water will collect and drop down instead of sliding in pan.
  11. http://www.cornelius.com/ Go to product tab. ...

    http://www.cornelius.com/ Go to product tab. And what color is your Mice maker:LOL:
  12. Replies
    30
    Views
    2,652

    I`ll second that.

    I`ll second that.
  13. Replies
    3
    Views
    1,048

    good show

    good show
  14. Have you checked your Pump on hydronic side to...

    Have you checked your Pump on hydronic side to make sure of circulation. It would be like a restriction in air coil with dirt build up
    causing head pressure to do Like what you said. Also Can you...
  15. Replies
    10
    Views
    1,379

    That rubber plug has cracks been on there quite...

    That rubber plug has cracks been on there quite awhile ago.
  16. Only way this is related to this thread copper...

    Only way this is related to this thread copper tube in compressor shell. Long while back I was given a compressor to change on a unit,
    the fan was too close with stub being pointed up. I had to...
  17. For starters you will need compressor, start...

    For starters you will need compressor, start components, Driers, a lot of screens, If it was a slow burn you will see it through system, I have seen some devices need to be unsweated to clean or...
  18. Replies
    9
    Views
    1,844

    Also seen where wrist pin would ping against...

    Also seen where wrist pin would ping against cylinder causing deep grooves.
  19. Replies
    8
    Views
    1,429

    http://www.hvacfun.com/f-design-refrigeration-syst...

    http://www.hvacfun.com/f-design-refrigeration-syst.htm. At this site it has your dimensions and talking about 800 lb of meat
  20. It maybe mechanically toast. You may need another...

    It maybe mechanically toast. You may need another compressor to start with.
  21. Replies
    29
    Views
    3,466

    Was at a gas station store there are 8 of them...

    Was at a gas station store there are 8 of them around 50 mile radius. This particular store had Manitowoc Ice machine exact same one in your pics in back room. 400 lb bin, Black mold under evaps and...
  22. http://www.johnsoncontrols.com/content/us/en/produ...

    http://www.johnsoncontrols.com/content/us/en/products/building_efficiency/integrated_hvac_systems/Industrial___Commercial_HVAC_Equipment/indoorpackaged/watersourceheatpumps.html York in st Louis is...
  23. Replies
    61
    Views
    6,169

    Just a guess, Have these condensers been split to...

    Just a guess, Have these condensers been split to clean? Awhile back one of our accounts was not keeping up. You could run water through it. split and clean little seeds and strands from plant life.
  24. Replies
    2
    Views
    518

    On start up. Did you weigh in the refrigerant?...

    On start up. Did you weigh in the refrigerant? adding gas as it is running? You have a restriction it may seem, not enough info to see through this monitor of mine.
  25. Replies
    19
    Views
    4,079

    http://www.fscc-online.com/HIW-Economizers%20(Spri...

    http://www.fscc-online.com/HIW-Economizers%20(Spring'99)/hiw-economizers.html

    Here is some reading material so you can grasp all that you can. I found that at google typing in economizers.
Results 1 to 25 of 366
Page 1 of 15 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event