Search:

Type: Posts; User: jrevans

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    374

    Also...

    I also read that even with the Bacnet/IP gateway (LGR) installed, you need to use WebCTRL to specifically set the points to be visible via the Bacnet/IP interface. I forget how, but it was discussed...
  2. Replies
    7
    Views
    492

    LOGO

    I've worked with a few LOGOs. Really basic, entry level PLCs are all they are.

    If you have LOGO!Soft Comfort software and the serial or USB cable (I recommend the USB cable) you can connect to...
  3. Replies
    22
    Views
    2,105

    Oh, that makes me sad (N4 still using some Java)

    Oh that makes me sad.

    Like some of the others, I hadn't heard any firm details about N4, besides it "wasn't going to use Java".

    Now, I hear that it is going to use some Java. Argh! I...
  4. Replies
    7
    Views
    520

    Us too

    We have a large R2 system here at our plant and I too am keeping my eyes open for what we'll need to do in order to upgrade. Since was also have an Niagara Ax (3.6) system in the facility, it will...
  5. Replies
    4
    Views
    465

    Another possible option

    I'm pretty sure that the Siemens WinPM.net system will also work with those ION meters.

    The older versions that I've used have been pretty crappy at times (from a developer's standpoint) but it...
  6. Replies
    25
    Views
    12,128

    V to mA conversion circuit

    Apparently that link is now dead. Here's the updated link:

    http://edn.com/design/power-management/4371307/Convert-1-to-5V-signal-to-4-to-20-mA-output
    ...
  7. Replies
    20
    Views
    2,549

    Chiller controlled by a George Foreman grill

    Ha! I almost spit out my coffee while reading that one! :putergreet:
  8. Thread: Service tool 5

    by jrevans
    Replies
    7
    Views
    967

    What I found

    Not my area, but some searching showed me this document:

    ftp://ftp.mingledorffs.com/Tech_Service/3V_Contractor_CD/3V%20Information/Pricing/3V_PricePages.pdf
    which shows CEAS121367-07 being the...
  9. Replies
    6
    Views
    770

    airnowapi.org

    I certainly can't figure out how to get the air quality readings. The provider site changed and then changed again. The last time that I checked, it was now with airnowapi.org where you have to...
  10. Wow, that was easy. Thank you for directing me...

    Wow, that was easy. Thank you for directing me there!
  11. Good luck indeed

    I agree with the "good luck in stopping them" quote.

    I'm an in-house industrial controls engineed who does BMS and regular controls, and it is very difficult to keep network connected machines...
  12. R2 binary "delay on" needed

    Man, I hate to post on such an old thread, but I'm not familiar with the R2 world, and I need a "delay on" function on a binary line.

    I have a BI that's driving an autodialer, and I want to put a...
  13. Replies
    39
    Views
    2,886

    Yeah, it's cold

    Also here in Eastern Pennsylvania and to add a twist to the coldness, we're apparently experiencing a bit of a gas shortage, both natural gas and propane.

    How that can happen when our state is...
  14. Replies
    31
    Views
    3,235

    Firmware

    Firmware is a form of software, but I certainly wouldn't classify all software as firmware. Actually, I would classify very little software as firmware.

    I'd say that firmware is 'embedded...
  15. Replies
    31
    Views
    3,235

    Nest issues

    Apparently Nest thought that it was a good idea to automatically push out firmware updates to their deployed products, without their customer's knowledge....
    ...
  16. Cooling in Antartica

    Interestingly enough, I just read an article yesterday about cooling electronics in Antartica, and how the dry air makes it difficult.
    ...
  17. Replacement parts

    And I already posted that CarbonBrush makes a drop-in replacement for the TI product. Why wouldn't they just buy that? Odd.
  18. I've never seen it work

    Late reply here, but we've never gotten a USB<->Parallel port adapter to work with a HASP or any other parallel port hardware key, and we tried about three different adapters. Apparently the...
  19. No personal experience

    I personally don't know anything about the product, but there are some on eBay, and I see that a drop-in replacement module is listed here:

    http://www.carbonbrush.com/replacementmodule.pdf
  20. Thread: Network Hub

    by jrevans
    Replies
    9
    Views
    917

    Linksys quality

    I've been having failure problems with the smaller four and eight port, blue Linksys switches for years. As matter of fact, I just swapped another one out last week. I had a report of...
  21. Replies
    8
    Views
    691

    I too use Oracle VirtualBox

    I too use Oracle VirtualBox for XP and although I'm running on a decent i5 machine with 8GB of RAM, running a few apps on both the Win7 and XP side with really kill that machine as it gets low on...
  22. Replies
    37
    Views
    3,322

    Sorry to hear

    Sorry to hear the sad news Osiyo, and I can't imagine the anguish that you're feeling. :(

    My thoughts and prayers are with you during this difficult time.
  23. Replies
    13
    Views
    4,802

    Only older versions

    Here's some documentation for WebCtrl version five, but I couldn't find anything newer out there:
    http://www.airsystemsinc.com/materials/techdocs/WEBCTRL.pdf
  24. I wasn't going to post here, but....

    I wasn't going to post here, but I wanted to let this forum know that I think very highly of you all. (I grew up around Pittsburgh, so I should say yinz.)

    I'm not a real HVAC guy, just an...
  25. Partial success

    Well, I sort of have success....

    After reading the help files about Tuning Policy, I created a new tuning policy and set the "Max Write Time" to ten minutes.
    423711

    Now, when I cycle power on...
  26. Tuning Policy

    Thanks for the tip MatrixTransform. I found the tuning policy (it was using the Default Policy), but the settings seem to indicate that the device should write when it comes back up:
    423581

    I...
  27. Ax/ G3 Digital Output on Modbus/TCP device stays off after power cycle

    I have a Moxa ioLogix Modbus/TCP I/O device that I'm using to grab some inputs and drive some outputs on my Niagara AX Version 3.6.47 system.

    I just discovered that if I cycle power to the...
  28. Replies
    3
    Views
    646

    About those Modbus groups

    These groups are the data areas that are associated with the different "Function Codes" that Modbus uses.

    Wiki actually has a decent breakdown of them:
    http://en.wikipedia.org/wiki/Modbus
    ...
  29. Replies
    13
    Views
    1,650

    Gotta check it

    Whenever I'm given an IP address, before connecting my device, the first thing that I do is try to ping it, to make sure that it's not already active on the network. I have caught a few that were...
  30. Replies
    3
    Views
    920

    Thanks for the follow-up

    Thanks for the follow-up Merkas. I'll have to take a look at their new "ICC Configuratiuon Studio" software.

    Our XLTR unit has been rock solid for at least several months now.
  31. Replies
    3
    Views
    920

    I used an XLTR-1000

    I used an ICC XLTR-1000 last year to interface a Sullair air compressor with our BMS system via Modbus.

    I didn't use the Siemen's FLN SLave protocol, but I was impressed by the device. It's...
  32. Thread: Serial Server

    by jrevans
    Replies
    6
    Views
    661

    We use both Moxa and Lantronix

    We use both Moxa and various Lantronix devices throughout our plants for serial to IP conversion.

    We have firmware for some of the Lantronix devices which translates RS485 Modbus into Modbus/TCP. ...
  33. Replies
    7
    Views
    1,306

    Interesting

    Interesting. I never checked the license on our Schneider TAC "G3" server, but it shows this:


    Brand
    brandId = TAC
    accept.station.in = *
    accept.station.out = *
    ...
  34. Use Obix

    As gowiththeflow mentions, we use the Obix driver to share some points between our R2 server and our G3/AX server. It's an almost seamless way to access points from the other machine.
  35. Replies
    10
    Views
    1,488

    I agree with TCF

    I gotta agree with TCF. It's much easier to learn after you watch how ALC does the system programming.

    I learned ALC from watching over the technician who came in, and then started making...
  36. Replies
    10
    Views
    1,305

    Unless you're attempting to view an ALC system,...

    Unless you're attempting to view an ALC system, which works ONLY with Internet Explorer, apparently due to their usage of ActiveX components. (Well, I can use Firefox with IE Tab, but that's...
  37. Non-Compliant?

    Now this sounds interesting! Any more details for the unwashed masses?
  38. Replies
    14
    Views
    2,995

    Sketchup (not ketchup)

    Which app is also by Google? http://www.floorplanner.com seems to be a web based service, and not associated with Google. I'm confused (as usual...)

    I've started using Sketchup at home (I need...
  39. Replies
    8
    Views
    1,478

    Update on failed OPC points

    As an update to anyone who happened to be following this situation, it appears that we now have the points working.

    As discussed elsewhere on here, the 3.6.47 release of AX had some improvements...
  40. Electrical tape

    Am I the only one who prefers to cut their electrical tape (usually with dikes) instead of ripping it? I'm a desk jockey, so maybe I'd do differently if I was an installer and had limited time,...
  41. Replies
    17
    Views
    2,762

    Isn't that the truth! :grin2: They have...

    Isn't that the truth! :grin2: They have officially morphed into a mobile phone sales store, but I'm thankful that they at least still carry some electronic parts.
  42. Replies
    5
    Views
    1,600

    A number to call

    According to a recent email that I got from Tridium Tech support, they said:

    > If you need to find a different Niagara supplier, we recommend you
    > give Schneider a shout at (815) 637-3000. ...
  43. Replies
    20
    Views
    4,479

    Depends on the instructor

    From what I hear, the class depends greatly on the instructor....

    My supervisor had JCI training in Arizona last year and it was not so good, but this year he had a class in Baltimore and said...
  44. Replies
    0
    Views
    1,622

    Vykon AX Supervisor upgrade problems

    I've been having OPC problems on our "G3" server which is running Niagara-3.6.31 and it was suggested over on niagara-central that I upgrade to 3.6.47.1 since there have been many fixes. I obtained...
  45. Replies
    8
    Views
    1,478

    Points still dying

    No dice. :gah:

    The points lasted about a day as normal before stopping to update, and not showing any error when they failed. That's quite annoying when you think that the points are okay...
  46. Replies
    8
    Views
    1,478

    batch limit

    That is something that I did not try. I'll give it a shot and see if the points stay alive any longer than they do now.
  47. Replies
    17
    Views
    1,947

    Well, Tektronix (and Fluke) were purchased by...

    Well, Tektronix (and Fluke) were purchased by Danaher ( http://en.wikipedia.org/wiki/Danaher_Corporation ) so their quality will likely be declining.... Having worked for a company that was...
  48. Replies
    17
    Views
    1,947

    Make it here

    That's even better, but for now I'd settle for "Made in the USA" just to get people back to work!

    I've met a lot of people in Kentucky who work for Toyota, and even though their company profits go...
  49. Replies
    17
    Views
    1,947

    Yup

    Yup, Walmart does have some Made in USA stuff, and I do try to look for those products. I recently was buying some socks there and noticed that with the ones that I was looking at, there were packs...
  50. Replies
    8
    Views
    1,478

    G3 server communication woes (OPC and Obix)

    Dang, I am still losing points, but the failure mode is now different since I turned off "Switch to sync io". Now it doesn't show the read fault errors, but the points just stop updating even though...
Results 1 to 50 of 129
Page 1 of 3 1 2 3

Related Forums

Plumbing Talks | Contractor MagazineThe place where Electrical professionals meet.
Quality Home Comfort Awards