Search:

Type: Posts; User: lontshooter

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    13
    Views
    1,332

    Dapper, One of the things with the shell command...

    Dapper,
    One of the things with the shell command in Hyper terminal is you need to have the proper settings to connect to the shell, those settings are:
    Bits per Second: 115200
    Data Bits: 8...
  2. Replies
    3
    Views
    565

    glasshouses, IF you could give a little info...

    glasshouses,

    IF you could give a little info on the system, I would be able to help you out.
    Is there a time schedule or is it a ATS attached to a point in the system?
    What is the main...
  3. Replies
    2
    Views
    515

    381engineer Been busy and not alot of time to...

    381engineer

    Been busy and not alot of time to get here, but here it what you are encountering with those inputs.
    They are ave inputs, but they scan only a small number of inputs on the ave then...
  4. Replies
    57
    Views
    4,577

    Bacnet, My position is that you can use any...

    Bacnet,

    My position is that you can use any good open protocol you want.... or you can use Lon or Bacnet. Doesn't matter to me because in this changing world you will now have to work with both....
  5. Thread: CSI 7797

    by lontshooter
    Replies
    16
    Views
    1,707

    Gazoo, The easy way to clear the device and...

    Gazoo,
    The easy way to clear the device and redownload the sav file to it is to use the red button on the board to reset the controller and power it down and power it back.
    Reload sav file for...
  6. Replies
    6
    Views
    1,614

    I am intrested in the MR88R-C, shoot me an email...

    I am intrested in the MR88R-C, shoot me an email in my profile.

    Lontshooter
  7. Replies
    25
    Views
    2,592

    dapper, I am with you on this one also. I had...

    dapper,

    I am with you on this one also. I had to replace a E3 with a SS2.0.
    I ran into the same issue that you are having.
    Make sure that you have the CS4 release of contribute to work with, you...
  8. Replies
    24
    Views
    8,330

    The big splash will be at ASHARE in Las Vegas for...

    The big splash will be at ASHARE in Las Vegas for the software which will be name StructuredWare on the Wonderware platform.
    Lots of engineering time is going into this product to make sure the...
  9. Replies
    9
    Views
    2,400

    kontrolphreak, Have you tried leaving the...

    kontrolphreak,

    Have you tried leaving the username and password blank and just hit enter.
    Then the next would be username: admin and password: leave blank
    Then the other one is username: user...
  10. Replies
    4
    Views
    1,024

    blx1 You have mail. Lontshooter

    blx1

    You have mail.

    Lontshooter
  11. Is there a limit to length of Lon wire ran from...

    Is there a limit to length of Lon wire ran from stat to stat?
    Go to this link and look at page 36 & 37, but I would read the whole document as it will help you out.
    ...
  12. DavyB, I have had one issue with that stat and...

    DavyB,
    I have had one issue with that stat and about the same issue that your are having now.
    First thing that I would be looking at is the stat and if the XIF file is loaded into the stat...
  13. Replies
    12
    Views
    2,478

    Amigo, You've got mail Lontshooter

    Amigo,
    You've got mail

    Lontshooter
  14. Replies
    12
    Views
    2,478

    You've got mail Lontshooter

    You've got mail

    Lontshooter
  15. Replies
    12
    Views
    2,478

    Azzad, Any programing or control of an...

    Azzad,
    Any programing or control of an Invensys/TAC system is done thru Workplace Pro and Workplace Tech.
    There are two sides to Invensys/TAC, one is the LON side and the next is BACnet.
    With both...
  16. First question are you using a router or switch...

    First question are you using a router or switch that your computer and the LIP are connect too, or are you connected directly to the LIP from your computer?

    The default IP address for the LIP is...
  17. Replies
    14
    Views
    5,018

    Crestron uses what they call Crestronet for there...

    Crestron uses what they call Crestronet for there commnication format.
    They will not talk directly to any device other than a Fieldserver device.

    They have agreement with Fieldserver to produce...
  18. Replies
    14
    Views
    5,018

    kontrolphreak What are you looking to...

    kontrolphreak

    What are you looking to Integrate with Crestron.

    Have done a few projects with there systems.

    Most common communication is either RS-232 or a LAN connection, but there are...
  19. Thread: Distech

    by lontshooter
    Replies
    23
    Views
    2,496

    Mechinc, This should help you out to resolve...

    Mechinc,

    This should help you out to resolve your issue with the controller.

    Need to remember that you can not retrieve the code using the new GFX programming software.

    You need to use the...
  20. Replies
    3
    Views
    1,784

    refrige-nate, Couple of question for you to...

    refrige-nate,
    Couple of question for you to allow for more help.

    How long is the run for the main trunk line from computer to farest device?
    Are there already repeaters in the line for the...
  21. Replies
    2
    Views
    528

    Do you have a copy of the SAV file that you can...

    Do you have a copy of the SAV file that you can email to me and will look at it.

    Lontshooter
  22. Replies
    62
    Views
    9,233

    Well I have heard the rumors running around my...

    Well I have heard the rumors running around my area also.

    The Delta guys out here have been told to keep a lid on everything and not talk about JCI and Delta.

    If JCI buys Delta, it will give...
  23. There is a file installed with some of the newer...

    There is a file installed with some of the newer programs for checking you licensing status, that is called FNP Licensing Service.
    It is common to Adobe software.
    It was design to check the status...
  24. Replies
    4
    Views
    1,296

    erod71 You need to get the software Workplace...

    erod71
    You need to get the software Workplace tech by TAC version 4.0 and better, to be able to due balancing on the Micronet controllers.
    The software is properiatary to TAC(oops!!!!) Schneider...
  25. Thread: Time_SNVT

    by lontshooter
    Replies
    3
    Views
    597

    Gazoo SNVT_time_stamp#LO: text(date(year,...

    Gazoo

    SNVT_time_stamp#LO: text(date(year, month, day), (" "), time(hour,
    minute, second))

    It is how the time stamp is defined see above.

    This would be from a controller that you want to...
  26. Replies
    5
    Views
    698

    Praetorian The 203 model has 3 Universal outputs...

    Praetorian
    The 203 model has 3 Universal outputs and 5 Triac outputs.

    Make sure that you have your fan DO on a Traic and not a UI.

    Check the setup of the Point in the program of the GFX, also...
  27. Replies
    6
    Views
    2,093

    Have done a few installation of the Spinwave...

    Have done a few installation of the Spinwave sensor in Hospital ER rooms and operating rooms with the use of just one repeater in the system. Have also installed in X-Ray rooms with lead line walls,...
  28. Replies
    12
    Views
    2,558

    rjgddc There is no known driver in Tridum for...

    rjgddc
    There is no known driver in Tridum for INET2000 or INET7 system.
    The only way that you may be able to make it work is with the OPC driver for INET, otherwise you will need to install a...
  29. Replies
    43
    Views
    5,482

    Like Carb says, check your subnets first to make...

    Like Carb says, check your subnets first to make sure that everything is on the same subnet address.
    The scanner that Carb recommended is one that I use also, works great for all BACnet device on a...
  30. Replies
    5
    Views
    1,389

    Two things that come to mind, First thing is...

    Two things that come to mind,

    First thing is that Andover is part of Schneider/TAC and the software for programming is properitary, unless you get the complete software package with the system....
  31. Replies
    7
    Views
    755

    gnsy1 The first thing you need to know is this a...

    gnsy1
    The first thing you need to know is this a computer based web server or a device based web server I.E. ILON100 or ?

    The second item is if it is a computer then that would depended on the...
  32. Replies
    8
    Views
    2,741

    Scorphi, Go to the follwoing link and it will...

    Scorphi,
    Go to the follwoing link and it will help you to indentify the SVNT that use are using, along with the properties.
    http://types.lonmark.org/index.html

    This should explain what you need...
  33. Replies
    24
    Views
    8,330

    Could this be a Tridum killer in the works if it...

    Could this be a Tridum killer in the works if it does show it's head.

    Lontshooter
  34. Replies
    2
    Views
    569

    finney13 The first thing is that you need...

    finney13
    The first thing is that you need permission in Vista to allow the SQL DB to be modified.

    The next thing is to remove any instances of INET7 including the SQL folder under the C:\ drive....
  35. Replies
    6
    Views
    1,263

    Wonnyhell, To integrate the controller into...

    Wonnyhell,

    To integrate the controller into Honeywell, who need to know if the XIF was create in a Lon Management Tool, but the issue is if they use the standard xif file and did not update it...
  36. Replies
    24
    Views
    8,330

    If you know Wonderware at all, then you will know...

    If you know Wonderware at all, then you will know what TAC/Schneider is about to release with there new NSP platform.
    The name of it is still in the air but sources say that it could be...
  37. Replies
    6
    Views
    1,180

    Are there any grphic page that show the operation...

    Are there any grphic page that show the operation of the system?
    Take a look at the points under the summary page and see how many have calc's or other attributes in the system.
    It won't be easy to...
  38. Replies
    6
    Views
    1,180

    PaulDiglio What version of Inet are you using?...

    PaulDiglio
    What version of Inet are you using? Is it Inet2000 or Inet7?
    What type of DCU's are you working with? Model number would help.
    Any more information about the system will help also.
    ...
  39. Replies
    16
    Views
    1,912

    Crab This is the one that I use....

    Crab

    This is the one that I use.
    http://us.fluke.com/usen/Products/Fluke+287.htm
    It may be a little bigger than others, but it does everything that I could need in the field and on the test...
  40. Replies
    2
    Views
    514

    ECC-VAV Lonmark made BACnet

    This out ot be an attenetion getter.
    They took at LonMark ECC-VAV controller and as it says upgraded to BacNet, now if I understand Distech configuration correctly this is not possible for this...
  41. Replies
    17
    Views
    1,796

    Spent the time there and went to all of the...

    Spent the time there and went to all of the booths at the show.
    Yes Darryl was there and had the real only live working demo and hands on presentation of the show.
    Spent some time with Darryl,...
  42. Replies
    19
    Views
    1,452

    I get in on Sunday to just enjoy the Show and...

    I get in on Sunday to just enjoy the Show and good times.

    Lontshooter
  43. Replies
    13
    Views
    1,973

    Modbus IP would be better to use with the JACE...

    Modbus IP would be better to use with the JACE box, the Modbus RTU will have communication issue with the JACE.
    Make sure that when you connect the two togehter that you have the correct register...
  44. Thread: T.A.C.

    by lontshooter
    Replies
    18
    Views
    2,962

    One side of the TAC line is LON and the other...

    One side of the TAC line is LON and the other side of it is Bacnet.
    Which line are you going to work with?
    The software for TAC is properitary and can only be sold to TAC partner, is your company...
  45. Replies
    1
    Views
    514

    alerton pcl-bcnt

    Looking for usrguide or manual for this device.
    alerton pcl-bcnt
    Also what software is needec to program this device or is it auto-discovery when connected to the TUX backbone of the network.
    ...
  46. Replies
    16
    Views
    1,184

    lancerbomb08 The first thing that I would do...

    lancerbomb08
    The first thing that I would do will be to create a new network database and see if you can commission one of the boards in the RTU's.
    If that works then the DB that you are using is...
  47. Thread: TAC

    by lontshooter
    Replies
    6
    Views
    1,071

    GONFISHN The UNC 520 can integrate...

    GONFISHN

    The UNC 520 can integrate combinations of LON, Modbus, BACnet, or legacy devices with the appropriate optional drivers. It provides integrated control, supervision, and network management...
  48. Replies
    1
    Views
    1,259

    Alerton BCM-TUX Info

    Looking for manuals on configuring Alerton BCM-TUX device.
    How to connect to it?
    I know that I need Envision software.
    Do I need that to configure the BCM-TUX device?
    Are the points that come...
  49. Replies
    2
    Views
    475

    HandymanJim The software that you need is...

    HandymanJim

    The software that you need is propieratary to Schinder electric(formely TAC),

    The software is only available to Schinder Electric dealers.

    If you are looking to make small...
  50. Thread: RAYPAK

    by lontshooter
    Replies
    1
    Views
    420

    walmond, What seires controller are installed?...

    walmond,

    What seires controller are installed?

    Lontshooter
Results 1 to 50 of 250
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event