Search:

Type: Posts; User: xxcels

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    25
    Views
    1,618

    I just brought a uniweld vacuum..Works great!

    I just brought a uniweld vacuum..Works great!
  2. Thread: Low charge?

    by xxcels
    Replies
    10
    Views
    704

    Find the leak first with some leak detector (soap...

    Find the leak first with some leak detector (soap bubbles) before you charge it or else you some throwing money away.
  3. If you changed the capacitor then the motor might...

    If you changed the capacitor then the motor might be bad
  4. Replies
    14
    Views
    2,029

    I need to find a good company to work for too

    I need to find a good company to work for too
  5. Replies
    2
    Views
    518

    I was thinking of just Fabing one of my own but...

    I was thinking of just Fabing one of my own but i'll go double check everything first like you said..Thanks
  6. Replies
    2
    Views
    518

    Mr Winter walk-In cooler Drain Pan

    Mr Winter
    Walk-In Cooler

    I have a condensate pan that rust through. But can't seem to find the pan anywhere. There is no unit # anywhere except for the compressor.
  7. Replies
    21
    Views
    1,123

    GL! i'm looking to take the NATE test too

    GL! i'm looking to take the NATE test too
  8. MIGHT BE THE BOARD

    MIGHT BE THE BOARD
  9. Thread: Summer clothes?

    by xxcels
    Replies
    15
    Views
    1,401

    Just a grey company tee

    Just a grey company tee
  10. Replies
    2
    Views
    443

    They said it's U.S made. Cost about $400-$600

    They said it's U.S made. Cost about $400-$600
  11. Replies
    2
    Views
    443

    Uniweld Vacuum Pump 8cfm

    Anyone ever own a Uniweld Vacuum pump? Any feedback would be appreciated..
  12. Replies
    4
    Views
    2,143

    lol...damn you drunk

    lol...damn you drunk
  13. Replies
    10
    Views
    736

    I got 24v at the board. I traced it to the unit....

    I got 24v at the board. I traced it to the unit. The wires go into this little gray box (not sure what it is call) that clamp around a blue wire going into the fan relay. I am pretty sure that is...
  14. Replies
    10
    Views
    736

    After some troublingshooting today I notice on...

    After some troublingshooting today I notice on the ccn that the SFS (supply fan status) is off. But the blower fan is running. I reset the unit. It goes through its normal heating operation but the...
  15. Replies
    10
    Views
    736

    yes, the preimer link is mounted on the duct...

    yes, the preimer link is mounted on the duct below the unit.

    That's what I thought too that the OAT is only for the Econmizer but it seem to be locking out the unit. And there is no code for...
  16. Replies
    10
    Views
    736

    OAT failure effecting the heating cycle?

    Working on a Carrier M# 48HJ3006. The unit is on CCN. It is telling me there is a OAT sensor failure (reading -40). Is it effecting the heating cycle? I have to reset the unit to start up the...
  17. Replies
    14
    Views
    1,990

    mmm ok ill give it a try, but that does not...

    mmm ok ill give it a try, but that does not explain the owner telling me the furnace wont kick back on after a couple of cycle. He have to reset the whole furnace.
  18. Replies
    14
    Views
    1,990

    yes it does have a three wire.. is there any way...

    yes it does have a three wire.. is there any way for me to test it?
  19. Replies
    14
    Views
    1,990

    ignition module troubleshoot

    Carrier
    M# 58GS050-EB
    S#58GS-050-161EB

    Owner call me to take a look at his furnace. He said he have been turning the power switch off and on to reset the system when the furnace wont recycle. I...
  20. Replies
    18
    Views
    1,652

    After we did a new install 80%..customer call...

    After we did a new install 80%..customer call back the next day saying there is no heat. I went out to check it out. He pointed me to the return grill and said "its cold here"
  21. Replies
    16
    Views
    1,811

    There seem to but no Data plate on the unit but...

    There seem to but no Data plate on the unit but the cover of the manual

    M# 174-0 Series
    Gas furnace

    Yes, I checked the pilot and there is a strong pilot flame. I putted a new thermocouple...
  22. Replies
    16
    Views
    1,811

    So I have to get a slow opening valve? I'll look...

    So I have to get a slow opening valve? I'll look into it.

    Yes, I am reading 3.5 at manifold. I haven't check the inlet yet. So you are saying I might not have enough gas pressure?
  23. Replies
    16
    Views
    1,811

    Main burner blowing out pilot

    Need help working on a Residential climatrol furnace. I forgot the model #. I just installed a universal 24v gas valve and new thermocouple the other day. I got a call back today. Tenant complaint of...
  24. Replies
    24
    Views
    2,190

    School first.... it help me get a job.

    School first.... it help me get a job.
  25. Replies
    9
    Views
    694

    damn!

    damn!
Results 1 to 25 of 62
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event