Search:

Type: Posts; User: xgpcer

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    6,630

    life ain't simple but...

    if I keep the generator separate from the residential system and run extension cords direct from the generator to the furnace and sump pumps, is there any problem if I use the ground of the residence...
  2. Replies
    20
    Views
    6,630

    clarrification...

    jayhawker....pls clarrify...was the 720 watts the start up watts for the blower on my furnace or the whole furnace???
  3. Replies
    20
    Views
    6,630

    life ain't simple....

    jayhawker....thanks...i "had" intended to use the house circuit ground and would not have given a thought to shutting down the generator while running the furnace....did you encounter any problems...
  4. Replies
    20
    Views
    6,630

    generators vs THD of furnaces

    I am planning to buy a portable generator to power my Carrier 58MVP060 furnace but have been told that the circuit board and ECM blower motor may be sensitive to THD (total harmonic distortion)....my...
  5. Replies
    8
    Views
    1,876

    and if you know the cfm for low heat for standard...

    and if you know the cfm for low heat for standard install, this would give me a good benchmark on what i am getting for CF cfm....
  6. Replies
    8
    Views
    1,876

    also...just tried the heating cycle and the...

    also...just tried the heating cycle and the blower speed on low heat is very quiet...is there any tie in between the lowest continuous fan speed i can get vs the low het blower speed???...i would...
  7. Replies
    8
    Views
    1,876

    also...the manual says that the CF switches are...

    also...the manual says that the CF switches are set for 525cfm if SW3 is for CF but if all are off, then it will be set at factory default but does not list the cfm for factory default...
  8. Replies
    8
    Views
    1,876

    ..........it is set up for 350 cfm/ton and the...

    ..........it is set up for 350 cfm/ton and the continuous fan speed is the only thing i am trying to adjust...would like the minimum...but have heard there may be some problems with too low a speed...
  9. Replies
    8
    Views
    1,876

    dmonkey....060 is the 60,000 btu unit and with a...

    dmonkey....060 is the 60,000 btu unit and with a 2.5 ton AC....the SW1 switch has switches 4 and 7 turned on and SW2 {AC} has switches 1&2 turned on; SW3 has switch 1 turned on
  10. Replies
    8
    Views
    1,876

    dmoney....pin positions now arethe top one is on...

    dmoney....pin positions now arethe top one is on and the bottom two are off...which should be 525...
  11. Replies
    8
    Views
    1,876

    still working on trying to get my continuous...

    still working on trying to get my continuous blower speed down on my now one year old Carrier MVB060....one non-Carrier installer has told me that he heard there was a problem if the CF speed was set...
  12. I did go ahead and wade through the manual...as a...

    I did go ahead and wade through the manual...as a last resort...adjusted the speed via the thermostat and even sorted out the famous "dip switches"....i adjusted the CF dip switches all the way back...
  13. OOPS...i have the 58MVB-060 and my friend has the...

    OOPS...i have the 58MVB-060 and my friend has the 58MVP100...my themostat is not an infinty....but did follow-up on the manual and the on/off fan and did reduce my continuous fan speed tho i don't...
  14. i don't understand how it generatres more...

    i don't understand how it generatres more moisture either...can you explain????.....as for the T-stat, my guys don't understand it yet...they just ordered one in to try to learn it....yes, i live in...
  15. i have a carrier 58MVP infinity heat/cool unit...

    i have a carrier 58MVP infinity heat/cool unit that has been on line for two months and i want to lower the continous fan speed similar to that which a friend has on his five year old 58MVB...
  16. Replies
    7
    Views
    852

    Dash...no, i don't have the infinity...

    Dash...no, i don't have the infinity controller...i live in a small town and the carrier dealer won't put them in untill he figures out how to use them...he just put one into a trial unit...he...
  17. Replies
    7
    Views
    852

    you're right ...i need to add different air...

    you're right ...i need to add different air returns but in doing this i will eliminate the ones that make noise in the wrong places and in the end will not be able to get net extra returns but think...
  18. Replies
    7
    Views
    852

    my new Carrier 58mvb-1si furnace makes more noise...

    my new Carrier 58mvb-1si furnace makes more noise from the main air return than my old one....i intend to change the ducts but am limited in how....as i make these changes, can i monitor the...
  19. Replies
    3
    Views
    682

    rabadger...

    i'm not a pro but think you have suggested that i get a two stage Carrier or Ruud...which was my knee jerk.....and the reason that i thought that an oversized evaporator coil might be a better...
  20. Replies
    3
    Views
    682

    Bald Loonie...

    yup...i wish he was more worried than me...but i guess that i am starting from the noise and working back...he is recommending the standard coil for a Carrier 38txa 030 AC and i have not yet...
  21. Replies
    3
    Views
    682

    i am replacing my furnace and AC unit....i am...

    i am replacing my furnace and AC unit....i am down to the last item, i hope ...the evaporator coil...i believe that i need to select an oversized coil to provide the ability to run at the lowest...
Results 1 to 21 of 21
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event