Search:

Type: Posts; User: ararams

Page 1 of 11 1 2 3 4

Search: Search took 0.01 seconds.

  1. Normally a rack has the equipment to handle the...

    Normally a rack has the equipment to handle the backup of liquid before it hits the compressor,on single units it's a death sentence for that compressor.
  2. I hope you don't have an aftermarket accumulator.

    I hope you don't have an aftermarket accumulator.
  3. Did you replace the low pressure control with a...

    Did you replace the low pressure control with a new one? I ask this because there was a change in the setting. You are most likely working on a 2000 lb unit
  4. Replies
    19
    Views
    404

    There is a reason all machines have model...

    There is a reason all machines have model numbers,without it we don't know witch unit you are looking at.
  5. Replies
    2
    Views
    268

    May be the instructions are in Japanese and no...

    May be the instructions are in Japanese and no one can read it .
  6. Replies
    14
    Views
    1,239

    That's the biggest split system I have seen.

    That's the biggest split system I have seen.
  7. Replies
    10
    Views
    536

    Have you checked the discharge temp? Maybe the...

    Have you checked the discharge temp? Maybe the oil has started cooking. This is common with r22 systems with run away superheat,the same can happen with 410a or any refrigerant for that matter.
  8. If the arms are getting cold, how are the the...

    If the arms are getting cold, how are the the legs.
  9. Replies
    36
    Views
    3,973

    Stupidity has no borders nor language barriers.

    Stupidity has no borders nor language barriers.
  10. Replies
    21
    Views
    769

    I also think he's looking at a headmaster. ...

    I also think he's looking at a headmaster. As for the cooler (where the owner turns off the fans) I normally install a relay or contactor with a coil voltage similar to the evaporator fans in a...
  11. Thread: accumulators

    by ararams
    Replies
    3
    Views
    231

    Some have them on the bottom and they sometime...

    Some have them on the bottom and they sometime leak for no apparent reason.
  12. Replies
    5
    Views
    320

    Does the compressor have a decal saying it is...

    Does the compressor have a decal saying it is protecting itself by not pumping?
  13. Most if not all the products in there are package...

    Most if not all the products in there are package products, low humidity will not really affect quality. High humidity will definitely affect your beer because if it"s slimy, slips out of your hands...
  14. Thread: Whistling TXV

    by ararams
    Replies
    10
    Views
    743

    That whistling noise you are hearing is the...

    That whistling noise you are hearing is the universal language txv speaks, the oscillating part comes when the pressure varies with the fan cycle control. When a valve is well fed it's quiet but the...
  15. Replies
    10
    Views
    624

    You already have your amp meter in your...

    You already have your amp meter in your hand,continue using it to check how much amps is drawn by the run and the start windings. If they are both pulling amperage then you have good windings but a...
  16. That's exactly how I look at it because we are...

    That's exactly how I look at it because we are looking at a failed part.
  17. Replies
    19
    Views
    1,630

    Look in Snapon catalog. That's where I got mine.

    Look in Snapon catalog. That's where I got mine.
  18. Thread: TXV's

    by ararams
    Replies
    35
    Views
    1,905

    That will depend on bulb charge. Gas or liquid...

    That will depend on bulb charge. Gas or liquid valves can be installed in any orientation, mix charged ( gas and liquid in the power element) power should be installed vertically.
  19. I think there is a similarity between this...

    I think there is a similarity between this expansion valve, the blown headmaster (I have actually seen this happen) and a frozen water line burst. I am sticking to rapid heating of a liquid filled...
  20. (MOP charge from what I can see. So this will...

    (MOP charge from what I can see. So this will limit the pressure produced within the sensing bulb to a predetermined limit. ) has nothing to do with sensing bulb pressure,but it limits the suction...
  21. Where can I find more info on that statement?

    Where can I find more info on that statement?
  22. Replies
    46
    Views
    3,799

    Did any of your fords disc pad set last 210,000...

    Did any of your fords disc pad set last 210,000 miles? My 05 chevy did, now I on 103,000 on a '10.
  23. Thread: Pulley puller

    by ararams
    Replies
    33
    Views
    1,399

    One of the better puller that have not failed me...

    One of the better puller that have not failed me yet. I added a socket and adapter to my impact driver and now have the all new Impact Driven Puller.
  24. Replies
    45
    Views
    1,867

    Your temperature sensing devices needs...

    Your temperature sensing devices needs recalibrating (you may need to keep your hand in a well stired mixture of ice and water ). then recheck temperatures in degrees.
  25. Replies
    27
    Views
    1,969

    The crane which cleaned that mess up did not use...

    The crane which cleaned that mess up did not use his outriggers either.
Results 1 to 25 of 255
Page 1 of 11 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event