If it is pre programmed, you have to go into controller and set the original parameters as what was on the last boad
Type: Posts; User: AddMore22
If it is pre programmed, you have to go into controller and set the original parameters as what was on the last boad
Seer rating has nothing to do woth pushing air to the second floor. Its just an efficiency rating. I would wonder if he 2nd floor damper is actually workinh and opening up to allow air to the 2nd...
Lol @ " are you an engineer"
Sent from my HTC One X+ using Tapatalk
Not "military".... Marine...( as in ocean ).
Sent from my HTC One X+ using Tapatalk
You want money ? Go marine.... Offshore hvac on rigs and ships.
. A lot of travel... I've been around the world twice.
Sent from my HTC One X+ using Tapatalk
Dumb question but.... Is the blower running......
Sent from my HTC One X+ using Tapatalk 4
No... I ment that is there were a restriction in txv the unit would act as if it was pumping down.....
Also is the condenser fan blowing good and correctly?
Sent from my HTC One X+ using...
If it was stopped up it would be pumping down or acting like it... Is it a 410 txv ?...
Oh... And is the bulb attached correctly?
Still dont sound right. If it was working before and not after..... 4 lb is a lot for a res unit..... If the motor is backwards or wrong speed it would seem as if it would be low on Freon..... ...
What's wrong with that ? .....
Sent from my HTC One X+ using Tapatalk 4
I would tell your hvac pro u want a txv.
I will tell you this much....I think it's a bad idea to buy a used unit....
Drilling rig house.... variable speed drive house.... Low voltage.
Catching a ship to Puerto Rico tomorrow..chill water barrel
Installed on drillers cabin MCC
336411
Sent from my iPhone using Tapatalk
336311
Sent from my iPhone using Tapatalk
Or like this
323671
Sent from my iPhone using Tapatalk
I just bought this and it had a blueish green hue. Does anyone have any ideas what's up?
Show off !! :)
First off a breaker can "trip" and still be in the on position. It may be a weak breaker .... Feel the OUTSIDE of the breaker (not the sides or anyplace the wire go in). Off the breaker is hot at...
Seems to me that I is undercharged .. It's hard to say... Need more info.
U can get any treated with harisite
Ok... That's what I ended up doing... This was the first time I set an Unloader using 404a. And for whatever reason I couldn't get it up... I suppose I could have turned off the 2nd stage comp to...
It doesn't matter if you have a jet engine on it .... If your duct work will only allow X amount of CFMs then that's all you will get...
Well... Fully loaded the suction pressure is lower then desired pressure ... So closing off valve only make it worse....
Ok guys..... I'm having a brain fart here ... I think the ref got off... 404a
5h40.
Unloader on back unscrewed is loaded .... Then set suction to what u want Then adjust u loader ?
By "upping" your motor all you are doing is pushing more air across your coil, thus less heat transfer..... = hotter coil
perhaps if you didnt want to upgrade you could look into sealing your...
Just a joke
Well a ferry
(not the man type)
274731
274741
274751
274711
274721
Osmosis
Yeah WITH A 100% backup
I'm not sure this is the proper place to post but I want to start this thread to shed a little light on what we do. Also for the most part keep a "log" of where I've been.
Came home Saturday...
I agree with you... I was being funny ....
Obviously you don't use ethanol as refrigerant
I beg to differ mister ....
suppose one chose to run ethanol in ones unit .....
407C
Dump liquid in receiver until u get proper subcool
Lol @ powerhead...
I always pull a triple when changing power heads .....
LMAO!!
Business ethics 101
Regardless if he needs a trap or not .... That's not going to help the fact that water is falling from the cool straight to the floor... A trap would not help this issue.
I think it is more of...
It's a nov rig? I thought they were just a service company.
272811272821
SCR house ... Just so people would know what we're talking about
Fan coil.
Huh.... Is it a scroll? And no kind of staging or unloading junk? What drilling company?
I work for Nance.
And I'm not sure for the reasoning behind that other then some engineer pencil whipping something.
Two replacements on a ship.... Not 100% done...
272781
272791
Most of the time
Lol... The company I work for builds custom units for that exact reason .... I do not work in shop, so I don't know all the details.
272771
What rig is it? On SCR houses the cond. units are right near the large transformers and 9 times out of 10 it's Insanely hot back there. Perhaps they over sized to adjust to the outside heat.... ...