Search:

Type: Posts; User: StillKicking

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    2,478

    Is this the same problem; "Trane Summit problem...

    Is this the same problem;
    "Trane Summit problem
    Started by brothdavid, 12-07-2012 04:40 PM" ?
  2. The customer doesn't care how much you know 'til they know how much you care.

    Those words are worth a thousand pictures!
  3. Replies
    2
    Views
    397

    Tracer 'Idle Time'

    How can I determine a true amount of idle time for a BTMX with V17? Is this an important troubleshooting tool? I appreciate any help with this.
  4. Replies
    6
    Views
    1,062

    Have you cleared the alarm log? Done any types of...

    Have you cleared the alarm log? Done any types of resets? You could pitch a high cap memory card, or better yet sell an "upgraded " BCU. I would try to test the BCU with new receivers first...
    10...
  5. Replies
    34
    Views
    2,082

    Sorry to hear of your wifes' pain especially here...

    Sorry to hear of your wifes' pain especially here at Christmas. I hope all turns out OK. My prayers are with you and your wife for her to get well soon.
  6. Replies
    13
    Views
    859

    Check out a thread titled "Got my first G5 today"...

    Check out a thread titled "Got my first G5 today" on 3-14-07. The G5 has been the best I've used and that includes Ridgid, ThermalTech, Trane Toter, Oz, MicroVac, and probably a couple of more...
  7. Replies
    2
    Views
    893

    If not being done already, this may be a good...

    If not being done already, this may be a good time to stress the importance of preventative maint. including annual megger testing, oil analysis, and tighten all electrical connections. Sometimes the...
  8. Thread: Vfd

    by StillKicking
    Replies
    5
    Views
    878

    what is the drive controlling ?

    Vfd

    --------------------------------------------------------------------------------

    Why does my unit ramp up the vfd to 100percent. What is it trying to satisfy. When it ramps up my building...
  9. Replies
    8
    Views
    744

    I thought design data was kinda " Job Specific "...

    I thought design data was kinda " Job Specific " but general stuff - I can help.:D
  10. Replies
    19
    Views
    5,125

    upgrade

    A TXV will always outperform an orifice. I've seen units with new compressors pull a vacuum at start-up because crap clogged the orifices. The failed comp. sent debris through the condenser to the...
  11. Replies
    18
    Views
    2,645

    Old recovery tanks

    Make good ice traps, use out of date tanks add a dip tube and replace the valves with a 3/8 fitting-or whatever line size is being used. Series two tanks before the pump. I've also used an old tow...
  12. Replies
    6
    Views
    835

    Just out of curiosity, does Trane support networks?

    I wasn't sure if Trane wants Tracer Summit on networks. If so- who said so?
  13. Replies
    62
    Views
    3,817

    Gee-I thought about starting a " Chiller Service...

    Gee-I thought about starting a " Chiller Service Company " once. Lets see, License, Bonding, Insurance, EPA Compliance, Staffing, Building facilities (with related overhead), Trucks, tools,...
  14. Replies
    6
    Views
    715

    Process of elimination

    If you know how the sequence the devices are wired (you're in luck)' just break the link in the middle and see if the first half talk- then add more till you loose comm, or if you don't talk at...
  15. Replies
    14
    Views
    1,293

    "yu should just get rid if train"

    Gee and to think you could have just chucked the whole system and lived TRAIN free the rest of your (short) career!!!
  16. Replies
    12
    Views
    1,037

    Wey-tek has lasted several years with no...

    Wey-tek has lasted several years with no problems, except the battery falls out once in a while
  17. Replies
    9
    Views
    1,758

    I could'nt agree with dawgtchrr more. WSHPs I see...

    I could'nt agree with dawgtchrr more. WSHPs I see are 5 tons or less so 3 or 4 cfm would be fine for those:) .
  18. Replies
    20
    Views
    2,686

    Osha ?

    I've seen everything from auto radiators and kerosene salamanders to homemade tank less 460 v heaters. We buy ONLY UL listed tankless heaters now and for good reason...Safety. I'll check on where we...
  19. I use a pair of Ideal strippers with the wire...

    I use a pair of Ideal strippers with the wire cutters at the very end ( not below the pivot) and they have machine screw cutters too. This tool is bigger than their " T Stripper" pair and works great...
  20. Replies
    135
    Views
    5,893

    What? No Duff for Coolwhip?

    The best beer I've ever had was home brewed by a good friend that believes in excellence. Quality product comes from patience, experience, and willingness to spend whatever it takes. Micro brews are...
  21. Replies
    47
    Views
    3,917

    I use a "universal refrigerant" Yokagawa H-10 and...

    I use a "universal refrigerant" Yokagawa H-10 and Snoop bubbles. The Snoop dries fast on hot lines and freezes in cold temps but dries clean and verifies leaks. Big Blue works great to find leaks in...
  22. Replies
    15
    Views
    3,594

    See if Pueblo can help you set up a temp. acid...

    See if Pueblo can help you set up a temp. acid cleanup filter (external) and send a sample to them (or get them to analyze results if you have sent samples to them). They may help determine the...
  23. Replies
    14
    Views
    1,462

    In my experience, having a good water treatment...

    In my experience, having a good water treatment pro makes all the difference. References from other facilities in your area may be the best way. We have used Rhino Liner...
  24. Thread: ch530 key

    by StillKicking
    Replies
    29
    Views
    2,531

    Just out of curiosity, what did your local Trane...

    Just out of curiosity, what did your local Trane office say to you about getting a Kestrel key? What is your plan as revised software will likley be changed to allow only softkeys to work? Just a...
  25. Replies
    36
    Views
    2,706

    2nd opinion suggested

    Great post, Mark. I couldn't have said it better. My question is; Why are the compressors failing? I suspect the original install work started the problems and an objective (Professional) opinion is...
Results 1 to 25 of 91
Page 1 of 4 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event