Search:

Type: Posts; User: xornelasx

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    296

    thanks Un but I already have that Sensor group...

    thanks Un but I already have that Sensor group set up and points spelled correctly but it still does not read them.
  2. Replies
    3
    Views
    296

    CCN Network Data In

    Can anyone help?

    Why wont the CC6400 read a Network Data In point from a VAV controller?

    The VAV controller point is "TIMOV" for timed override in effect and "OVERLAST" for
    Override in...
  3. Replies
    2
    Views
    643

    Metasys VAV Controller help

    383781

    Does anybody know why this vav box is not running at cmaxflo? Space temp is above setpoint by 3 degrees. I uploaded a snapshot to this thread. Thanks in advance!
  4. Replies
    4
    Views
    666

    Junegemini: I need the DO's to maintain SAT...

    Junegemini: I need the DO's to maintain SAT setpoint by opening or droping when sthe SAT rises. I also need the SAT setpoint to reset based on OAT. In a nutshell I would like the Algorithm to behave...
  5. Replies
    4
    Views
    666

    CCN Algorithm Heat staging with reset

    I have a CC6400 and I'm looking for a way to use the canned algo's to control a 2 stage gas furnace (DO only) and also be able to reset the SAT based on OAT...Any suggestions? I was hoping that the...
  6. Replies
    1
    Views
    321

    cc6400 PB Override question

    WOndering if someone can help?

    I have a Carrier 6400 that is controlling a DO.

    This DO is tied to a TC Algo.

    The Algo is tied to an occupancy schedule.

    I have to temp sensors with push...
  7. Replies
    1
    Views
    356

    CC6400 Algo Problem

    Would appreciate any suggestions.

    Looking to control a two speed motor on a cooling tower in which the low speed drops out before the high speed kicks in. I looked at the canned algo's but nothing...
  8. Replies
    0
    Views
    534

    CCN Sensor Group Question

    Is there a way to do the following?

    I have 4 TC Algo's that are controlling various pieces of equipment.

    I want to use a software point in conjunction with a Sensor Group Algo which will show...
  9. Replies
    4
    Views
    910

    Balibe- Yes, please send me what you got on...

    Balibe-
    Yes, please send me what you got on Best...Thanks!
  10. Replies
    4
    Views
    910

    I have a cooling fan on a dual duct system that...

    I have a cooling fan on a dual duct system that is currently on a Time clock algo that I want to keep from starting on an occupancy call unless the return air temp from the hot deck is warm enough....
  11. Replies
    4
    Views
    910

    Carrier CCN Morning warm up question

    Does anyone know what Algo I can use to set up a sequence where I could hold back an AC supply fan based on temp without it being continuos?
    I was planning on adding a permissive Interlock to do...
  12. Replies
    3
    Views
    732

    Thanks Scroo- Will my points on the Summit...

    Thanks Scroo-

    Will my points on the Summit screen update themselves? What I mean is, will it now show the setpoint box where I can choose whether to use the thumbwheel or the BAS? Or do I need to...
  13. Replies
    3
    Views
    732

    Tracer Summit Question

    I have a Trane Summit BAS, version 16.00.0121 with service pack 4 installed.
    Its running several gas packs with Reliatel controls.
    Some units have thumbwheel setpoint control and others have just a...
  14. Replies
    3
    Views
    775

    Thanks Balibe for the info. It looks like it...

    Thanks Balibe for the info.

    It looks like it may be a NST vs. old software in the 6400 issue since i am using all the outputs on the 6400. I will double check the dip switch settings to confirm...
  15. Replies
    3
    Views
    775

    Comfortview 2.0

    I was wondering if someone could point me in the right direction.
    I am trying to view the hardware points locations for a couple of 6400's and i/o's that are on a Comfortview 2.0 system. I have...
  16. I-Vu + civ-cr bridge networking question

    Has anyone ever attempted to network a carrier ccn router (civ-cr) configured as a bridge to an Ivu plus that lives on an entirely different network? (e.g., two different DSL accounts)
    I believe the...
  17. Replies
    4
    Views
    784

    CCN Wireless Ethernet Bridge

    Has anyone used a wireless ethernet bridge on CCN equipment? Specifically the Carrier router configured as a bridge and connected to some UC's.
    The antenna manufacturer tells me they are working...
  18. Thanks Orion!

    Thanks Orion!
  19. Trane/Honeywell Economizer Module Connectors

    Does anyone know what the 2 and 4 wire connectors are called?
    They connect to the MAT and 24v & BAS points on the econo module of a Trane unit.
    Trane doesn't know what I'm talking about but they do...
  20. Replies
    1
    Views
    485

    Carrier CCN Comm Issue

    Has anyone had this issue?
    I have an old CCN system that I cannot pull tables from completely through Ivu.
    My Gateway shows that I have established comm but when I scan or rescan, sometimes some of...
  21. Replies
    1
    Views
    301

    Carrier Algo Question

    I have an interlock algo controlling my cooling relay. (interlocked with fan)
    I want to be able to lock out this cooling relay based on OAT.
    I originally set up an analog comparison algo to turn...
  22. Replies
    2
    Views
    534

    Thanks Balibe.

    Thanks Balibe.
  23. Replies
    2
    Views
    534

    Old CCN Equipment...At least to me.

    I recently uploaded a CCN site with the following components:

    32MPGTWY:3200MP GATEWAY

    EF/EX/FA: 19EF/EX/FA CENTR CHILLER

    DATCOLDT: DATACOL lll/DATA TRANS

    CHILLID2:LOCAL INTERFACE DEVICE
  24. Replies
    6
    Views
    728

    Thanks Balibe! Everything worked per your...

    Thanks Balibe!
    Everything worked per your recommendations.
  25. Replies
    6
    Views
    728

    OK- I currently have an I-vu router at building...

    OK- I currently have an I-vu router at building B. It is currently set up as a bridge. So what you are saying is to reconfigure it as a gateway?

    I currently have an I-vu router at building A. It...
Results 1 to 25 of 122
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event