That "JUNK" was pre-BACNet. The DCU 050 allows The V2 product to be seen via BACNet through Orcaview (Delta Software) but it doesn't act as a gateway.
Type: Posts; User: CE-TECH
That "JUNK" was pre-BACNet. The DCU 050 allows The V2 product to be seen via BACNet through Orcaview (Delta Software) but it doesn't act as a gateway.
Yes you can. In order to add the graphics to the DHMI you need to create them in illustrator first then convert to DHMI.
This would have to be setup through GCL+ in order for the "Manual" state to be reset. Either that or create a BV which then counts down and controls the AO or BO. Either way it requires GCL
The internet is amazing.. After 5 years I googled Chigo and found my own post.... I need a condenser fan motor for a CMV-V64WC9A. Anyone know where a fella could find one?
Does anyone have the part # for this snow guard?
Hello All,
Does anyone know if its possible to purchase a field install Barometric Relief Hood for a Trane YSC090A3EHA1P000000000000 Packaged Rooftop unit?
I am not getting very much help...
Something good to know about the BACnet gateway though is that certain SW versions only work with certain BACnet manufacturers. ie Delta works with 1.30.x, Reliable with 2.00.1d
Emerson claims that thier Einstien 2 controller is BACNet.
Has anyone ever integrated with this system?
If that doesn't work do you use Dropbox?
Sent from my BlackBerry 9900 using Tapatalk
Oh ok. Well you should call your local Delta rep and have them do a reinstall of the software
Sent from my BlackBerry 9900 using Tapatalk
It is currently VAV. Have you ever seen one of these units with a Fisen board that controls the gas heat section for tempering?
Sent from my BlackBerry 9900 using Tapatalk
yes its supposed to be. Its there incase the .dbr files become corrupt
Is there a security.dbr_bak file in the sites folder? If so then delete the security.dbr file. Rename the dbr_bac file to just security.dbr and try that.
Hey all,
Just wondering if anyone knows the answer to this. We currently have a customer that has 2 York Z34 RTU's. Currently they have the York BacNet interface on them. These also have the...
Use a RTS-424. It looks like the new BACStats. But be careful. You need to change the power from 8vdc to 24vac or smoke comes out.
Did you get this problem resolved?
Sent from my BlackBerry 9900 using Tapatalk
Can you email me? I am unable to send you a PM.
Sent from my BlackBerry 9900 using Tapatalk
Honeywell Analytics has the E3Point monitor. Has 4-20 ma output as well as can be a BacNet device. I have have put in 100s of them.
Sent from my BlackBerry 9900 using Tapatalk
Is ESC your local Delta rep?
Sent from my BlackBerry 9900 using Tapatalk
Ok. Well you next step is to now setup a program to control the output. What is it that you are controlling?
Sent from my BlackBerry 9900 using Tapatalk
First of all do you have programming access through Orcaview or Orcaweb? If not... Call someone who does.
Sent from my BlackBerry 9900 using Tapatalk
Sounds like there isn't a program controlling that output. Or the program isn't being called for by the Master Program
Ok. Well I haven't changed any configuration parameters when it comes to alarming or faults. So is there a base setup?
Can someone explain to me what causes the ABB ACH550 with Bypass to Automatically go into Bypass mode?
Does the Bypass somehow know if the ACH550 VFD fails? And what sort of failures force it to...
I appologize Cujo. Just seems like a DIY-er type of question. Some of those make their way into the forums.
Try this. Unless I misunderstand what you want
If Schedule on then
Switch(Fan...
Oh ok. So it works a lot like LON. We definatly don't have the file or the software so I guess its time to call Honeywell. Or tear it out and put in a Delta controller.
Is this a licensed software or open?
I have a customer who has asked me to look at his control system. I am primarily a Delta tech. What he has is a Honeywell XL80 system.
Does this require a propriatary software to configure? It...
I think this fella should probably call his normal control tech in. That is probably the most basic SOO I have ever seen.
I mean come on. Turn on Output when Temp < SP -1 then turn it off when...
Di you get this figured out?
You got mail!
Does anyone know if there is a code in Canada that requires fixed access to a roof if a building is over a certain height? If so does anyone know what this height is?
Hey guys,
I am looking at getting a new drill. I already run a DeWalt XRP 18V for anything major. I am looking to get something small that will easily fit in my Veto Pro Pac to take up on a roof to...
I am also looking for some IOMs. My unit is a XTI-051X054-FAKA
Any help would be great. I don't think the installing contractor put a deep enough drain trap on. I had a service call today about...
What size ORCAWEB key do you have? The software comes in different sizes? S, M, L.
S can only have a max of 250 points (inputs and outputs) M can have a max of 2500 points and L can have unlimited...
Just as ab example but with Delta you can only set the dip switches up to 127. This also acts as the MAC, but the Device Instance can go much much higher. Not 100% sure of that # but we have sites...
Thanks George
He tells me it doesn't seem to be during colder weather but today it was 6C and he did see it go into defrost a couple of time. What triggers defrost on these units?
I had a customer send me a few pictures of his Ductless Unit. Seems that the Outdoor coil is frosting up extremely heavily in heating mode.
I am not overly familiar with servicing these units as it...
Yes I know that what's I want to do. I will be doing the logic programming. Problem is that these ERVs don't have a contact on them for "stop wheel" I am trying to see if anyone know of where I...
I guess I should give a bit mor backstory. In this case I have an ERV inline with the Fresh Air Intake for an AHU. This AHU doesn't have any cooling so it relys stricktly on FA for cooling. Problem...
Has anyone ever had any luck in taking control of the heatwheel in a Venmar ERV3000i? If so any tips or tricks to share with a fella?
Does anyone know what the most recent 301C firmware version is?
I began as a HVAC service tech doing Supermarkets, then did some A/C for a few years now a Controls Service Tech as well as a Part-Time programmer.
Haha... That was the first thing I looked for
I am having an issue with a Bulletin 1333 VFD controlling a Heat Wheel
Seems that no matter what my drive will not ramp up over 4.5hz.
Usually before I even make it to this level the drive trips...
RuPaul!!! She is a woman right?
That's the problem. I don't have one. Ihave been asked to remove the UTL and install a LG. Just trying to find out what is run between then two without having to make the hour drive to go check.
Does anyone know what the wire from the outdoor to indoor units of a UTL Ductless heatpump Model # URHA-12WDC is? Is it 18/4 or 18/3 or something else?
Thanks for your help
Lots of posts no answers.... Let me go a bit deeper.
I am the tech that commisioned this drive. The Pump motor is a 600V 3phase
In group 98 on the ACH550 it is all set up correctly.
Would...