Check your email hopefully thats what you want.
Type: Posts; User: edwardjw
Check your email hopefully thats what you want.
Kevin is correct oem is best but i do think icm makes a replacement board that johnstones carries. When you pull old board look on the back of it have found several with short marks on them. good...
Call a plumber have him send his camera in the ductwork ive never tried that just an idea
I put Protreat in all evaporator pans that i service and havent had any problems so far two years going.
Its just to make the match with the width of your furnace both are rated the same otherwise.
I love them use to move pop machines with one and it would climb with no problems.
Are you in the trade because this is a no diy site.
Thank you very much
I know i should know this but could somebody give me a width for this furnace I looked at it four months ago and now im installing a new furnace tommorow and cant remember if its 14 or 17 inches wide...
I just installed a 40,000 btu furnace in a similar house as yours and it took all of 7 hours of running the furnace to get the slab to heat up.I told the home owner the losses up front and showed him...
Always hardpipe through cabinet then flex from there but try to hard pipe the whole way.Also galvanized pipe is a not allowed have seen it but inspectors would fail it here.
:oops:
carrier Van broke down today so dont have model numbers with me gas was off but power was on then would be shut off then on again to show property.Will post some model numbers tomm thanks
Just out of curiosity why would all the wires be cut? Ive only seen that done when there is a cracked heat exchanger and the tech does want home owner to try and put it back together.
Just got an account has 54 furnaces that havent been run for at least two years out of nine rooftops four inducer motors dead.Then 12 of the 26 split systems inducer motors are bad.Is this typical of...
Have you let the furnace run through a complete cycle yet to see if it will.And about the wiring the fuse was put in to protect the system.If its just a wiring issue then it shouldnt be that bad to...
You might look into buying a Prestons Guide very nice to have when you start out.
When I worked at a welding shop we use to take a peice of plate drill hole in it same size or a bit smaller and tig weld the pin to the plate.Let it cool then twist while pulling up and if it didnt...
Three years.
Installed 5 so far and havent had a problem yet kinda nice setup.
Poor oil return or no oil return.
I was installing electric heat on this unit today and after looking at schematic and I dont think I have the right kit 09WSJ1502B.From the wiring diagram cant see how this kit would work as supplied...
Only used it once customer wanted to try it on his system dad six holes in the evaporator.I mrked them put it in the system and charged sytem up came back the next day and no leaks got a call two...
Could you take the number off of the compressor and then contact a supply house for a cross.
Did you consider RX flush then blow out with nitrogen. Just my opinion.
It also comes to a point when you screw with your plumbing or tile work you dont have the potential to kill somebody or yourself.
Doesn't seem like a bad deal to me if it works and stays working then all is well.
The last one I worked on the wiring diagram was in a plastic bag taped to the bottom of frig.
call another company
A mod will be along shortly to remove your prices call another company for another oppinion and if you post model numbers and serial number could possibly be under warranty if it is only 4 yrs old...
Thank you for the replies ended up using hot water and coil brite worked but probably will start looking for something else to try.Simple green sounds like it will be used next time just never had an...
I was working on a randell prep table today iced up solid.Bad fan motor but as I was defrosting it there was black slime all over coil normally I just hose off but whatever this is doesnt want to...
The kink is definately part of your problem you have lost maybe half your capacity.
It has a SEER of 12.20 in cooling mode. Hope that helps.
My customer and I thank you very much.
Got a call on a Lennox RTU mod#GCS16-1603-270-2G for no heat. Pulled the panel off and all the wires have been chewed up by mice at the terminal block and i couldn't find a wiring diagram on any...
When I was in school if you had a problem with your system it became a class project everybody went there to fix it.
No its not its a constant flow
Thanks for your reply. Took apart control valve was clean and made sure it opened all the way also cleaned the flow regulator. I thought about checking the water flow going into the coil by timing it...
Hello and thanks in advance for any help. Working on a unit that is Mod#FCDB020 it was installed 9-06 and worked fine till about a month ago. There was construction going on in the building and with...
York/Coleman tech support 1800-228-7896