The iHarmony zoning control board is controlling all the equipment. Supply air target temperature is a set point in the parameters for the zoning control. It compares the value from the supply air...
Type: Posts; User: thepresence
The iHarmony zoning control board is controlling all the equipment. Supply air target temperature is a set point in the parameters for the zoning control. It compares the value from the supply air...
Yes, I figured out it was cycling the heat to keep the supply air target temperature.
Unfortunately yes. We have about 15 Excel classic controllers still running here. It makes my job as an HVAC tech difficult because no one here can understand the programming notes. Thanks for your...
Referring to the attached .pdf, can anyone understand this? This is programming information from a Honeywell Excel classic controller. I believe all the sequence of operation information in...
Thanks everyone for your replies. I will defiantly checked the amp draw when i open up the valves to see how it runs. The design drawings are probably here somewhere, it will take me some time to...
Here's a picture of 1. This one happens to be a glycol heat reclaim system.
I work in a large long term care facility and I've noticed on a lot of our closed loop glycol/water heating and cooling systems, the hand valves are throttled back to various positions on the outlet...
You've probably got a short or the wire is grounded on your electric heat control circuit. Ohm the wiring out to find the problem.
Sorry for the confusion and thanks for your patience. My email has been updated.
XP20036230A02
Thanks.
Anyone know if there is a COP chart for the Lennox xp20 for different ambient temperatures?
The only specs i've ever given when replacing one is the size, i've never been asked for the pitch. I suppose if you need to spec a replacement to a precise airflow there would be a fan curve chart...
The dye should specify how much you need. If not, an ounce or 2 would be plenty. Won't need much if the total charge is that small.
Just a thought, if your blower motor runs on startup, is there possibly a open high limit or rollout switch?
The way i think about this, if the first burner is going out but the 2-4 burbers stay on, the gasflow out of the orifice must not be flowing. If there is no obstruction then it must be a gas...
Yes you are right. I have a XP20
Lennox SLP98 90k btu
No, i have no bypass damper. I could install a bypass damper and raise the airflow, but why would i have the waste of a bypass damper when the heating system is capable of modulation?
I have a Lennox iharmony zoning system installed my my house. The problem i'm having is when only 1 zone is calling and the heat pump is operating in heat mode, it makes a vibrating sound from the a...
I've got a brand new SLP98UH090XV36C-09 i installed in my house with an S30 thermostat and a iHarmony zone control with 3 zones. When the zone control is connected to the furnace, the burners will...
Thanks, that is what i didn't get, and now i understand.
How does the Enthalpy Conversion chart work to convert Web Bulb temperatures to enthalpy? It seems very straight forward except the "tenths of a degree Fahrenheit" part. I don't understand this...
i agree with hvacker. You should do an initial evaluation of the equipment. If your taking over for someone who knew what they were doing, everything should be in pretty good shape. But if the...
Check temperature rise and go from there. If it's ok, your limit is probably bad. If it's too high verify there are no restrictions in the furnace and then increase the fan speed.
Can you confirm when the compressor(s) cut out that the voltage to the compressor terminals is still present? That will confirm whether you have a control cutting out or something internal in the...
Tommyz23: If it were an air to air, i would think the TXV is stuck closed and needs to be replaced.
Bergy: I have never checked the flow rate through a loop. How would i do it? I'm not sure...
Problem: Evap coil is icing up and not cooling space down to setpoint.
Data:
R410A 340 High Side 76.5 Low Side
10.7 degrees F Subcooling
78 degrees F EWT
82.5 degrees F LWT
SA - 64.6 degrees...
All the trane units i've worked on if it's a trane thermostat then then any standard thermostat will not work without installing the extra thermostat board first. You should be able to jump it out...
agreed.
If it's raining and there's an emergency refrigeration/ac call i would. It's only water and i'm not made of sugar. But lightening, no way.
could it be a crack in the heat exchanger that's only opening up after the furnace runs for awhile?
The lennox iComfort only needs wireless internet access. No additional gateway. It should work with any equipment as far as system monitoring/adjustment goes. But i have not actually tried it.
As long as the spec's match up, enclosed or open motor does not matter.
nice ones.
this is why i ask for no ice. gross!
at least once per year. I'm sure there's alot of ice machines out there that don't ever get cleaned. I always ask for no ice now after i started fixing them.
This is the Ask Our Pro's forum, and only Pro members that have been vetted by the AOPC may post advise, commentary, or ask questions of the OP here. Please apply to the AOPC today, thank you.
...
This is the Ask Our Pro's forum, and only Pro members that have been vetted by the AOPC may post advise, commentary, or ask questions of the OP here. Please apply to the AOPC today, thank you.
...