I have a Lynxspring Jene that was taken out of a unit being replaced. It was in a Valent unit.
How can I clear it out back to factory defaults? Apparently this was programmed by Valent and...
Type: Posts; User: scepter
I have a Lynxspring Jene that was taken out of a unit being replaced. It was in a Valent unit.
How can I clear it out back to factory defaults? Apparently this was programmed by Valent and...
I have been tasked with integrating 5 Trane MP 580’s into an existing LNS Lonwork system. I have no access to the existing system yet. No idea what vender. At this point in time they are requesting...
Thanks Reaper!
That is what I was doing wrong. I was openning Trabsfer.exe with windows.
When I go back I will open it in dos.
Thanks
Scepter
That is what I am using, a regular cable with a null modem adapter on it.
It works with the DX9100's.
I have a JCI Companion board that I am trying to upload the database to integrate to the system. I have Transfer.exe and Noterm.exe and I am unable to upload the database. I keep getting the errors...
Problem found. The BCU in question was a BBMD and come to find out there was Fieldsever that was a BBMD too with this BCUs address in its BBMD tables. We left the Fieldserver as the BBMD and have had...
1)Are your rj-45 connections solid? (YES, and even a new cable has been run and tested), have you tried a different port on the switch? (YES we have.)I would start there, have you brought IT into...
Not exactly. If we power down the device and reapply power is comes back on. We haven't just disconnected the LAN and then reconnected, if that is your question.
scepter
We have a Trane BCU and an iLon 600 in a building connected to the LAN. These two controls will lose and regain communications for no apparent reason. We are unable to ping either of their IP...
You stated earlier that you recommend replacing the dampers along with the actuators in a Carrier VVT system.
Why is that?
Thanks scepter
Thanks OK,
That is pretty much what I did. I need to double check my wiring just to be sure.
scepter
OK,
Can you tell me your pin configuration and describe how you are connecting?
What comm port driver are you using?
Thanks
scepter
We recently picked up a couple of building with JCI NCMs and UNTs and VAVs.
I picked up a copy of M-Tools and have tried to connect to building a couple of ways.
First I tried to go through the...
We have a RTAA that keeps tripping on “Phase Reversal Protection Loss”.
We have replaced compressor contactors and compressor Cts. We have no indication of the building loosing a leg of power or...
We have a building with the Parker Carrier control product. Customer wants to upgrade the control system. What we have as far as equipment is a VAV RTU that is sending the cool air down the ductwork...
I heard a rumor about who actual owns Alerton but I want to hear it from you guys.
The laptop is running XP pro also.
I have checked for windows updates and modem driver updates for the desktop. Everything is up to par.
When I try to connect, I have double checked and even...
I am having problems with my Dell desktop computer (running XP Pro) . I am unable to dial into a Honeywell LCB site that my Dell laptop can. With my laptop I am using a V92 Modem Blaster modem and I...
I have a McQuay chiller- AGZ050 that will not bring on the 4th compressor because it is sensing a high “chiller current” draw of 125% with three compressors running. I did check each compressor...
I have a new customer with several buildings with the Honeywell LCBS in it. One of these buildings I am unable to dial into the system. It is a very small site, just one Building Manager, a display,...
I for one enjoy osiyo’s posts when I am not in a rush. Sometimes I am just searching for the answer and with his posts one needs to take the time to “listen”. I find that he has a lot of knowledge...
Codewriter,
I like those pay rates.
What part of the country are you in?
You don't see rates like those in the South-East.
scepter
Dave,
That is how I am going to approach the customer next week. Just lay it out on the table and explain that what they bought a very proprietary system and we are currently unable to service it....
Freddy,
The display is very basic, just a numerical keypad with “backspace, shift and enter” buttons so when you ask about the F2 & F3 keys I don’t have it.
Yesterday I went through every point...
Can anyone out there sell this service tool, LSX 280?
Is there any other software that I could get that would allow me to access these controls?
The problems that I am seeing are that some area...
Freddy,
Without the CX-9XXX control can this system dial out alarms?
The Ix170, is that the Lap-top service tool? I see that listed as a LSX 280.
I have listed the controls in the electrical...
I inherited a building with an Andover Infinity system in it. This system contains one LCX810 with an EMX150 and about 12 VAV controllers (unknown model #s as of yet).
I was trying to connect to...
Thanks Code
That is kind of what I expected. Lon Station in a somewhat lower end system not produced for integration, correct?
All help has been appreciated guys.I know what I need now.
...
Ok guys, I see many different solution if I wanted (or should I say the “customer wanted”- $$$) to change out any of these controls. I am just trying to get a clear idea of what I have and what is...
Codewriter,
I am in S.C.
Any help would be appreciated
Check my profile or WWW for my contact info.
Thanks
scepter
All I NEED is to dial in for set point changes and receive dialed out alarms.
It would be beneficial to configure the network and such but cost is a factor.
Web servers and "costly" software is...
Codewriter,
How much then?
Can you sell it to me? How much?
I will be contacting our local Honeywell rep and see how much he says and I will post it.
Not trying to beat up on you Code and I...
OK guy, this is what I have.
Building A: Honeywell W7760A2011 Building Manager
Honeywell Display S7760A2031
Echelon Network Adapter to a modem
...
I am looking into installing a new fireplace in my living room. We are looking at using brick for the construction material. We want the type of fireplace that has a fan that will re-circulate air...
sysint,
I have worked on some DesChamps in the past and find that they are a pretty solid product. The controls that were in them were spec'ed Apogee and came through quite operational.
...
Doc,
I believe that the Voyager and TCM use different sensors. Check you documentation to see if what you are using is correct.
I had a problem were as we were installing 6 new TCMs and they...
What are these sensors wired to exactly?
VAV, PCM, TCM, Voyager RTU?
scepter
So what I am hearing hear is that Honeywell is discontinuing the software this month but has yet to have a solid replacement ready to go?
Don’t you just love it!
Seeing as how I am not even...
I was afraid of that.
It never seems to go well going through the manufacturer.
Again the benefits of Lon!
Thanks
scepter
Jomi,
Do you know the best place to purchase XBS software and dongle?
Do I have to go through Honeywell?
Thanks
Thanks for the help guys.
So let me restate this to see if I get it.
I will need CARE to perform any onsite type maintenance or controller change out, correct?
Is CARE a network tool such as...
sysint,
Please check on those parts. I’m sure we can work something out if they are available.
What kind of display module do you mean?
Jomi,
Might you have an extra copy of E-vision around...
My company just picked up a new account with about 100 +- buildings throughout our state. Several of these buildings have BAS systems of various kinds. Two of these buildings have Honeywell systems...
Logon as normal then before you do anything else
hit ctrl and x at the same time.
I usually do it a couple of times just to be sure.
That works on a facility that we work with.
Good luck.
scepter
kwillmech,
You stated:
If you want to use all the NVs in Summit then make yourself an XIF file (or DL at lonmark.org) and create a Summit GLD. You can create your own I/O property bindings to the...
Thanks for info Bald.
That should help
I have a customer with a York Guard IV control. The problem is that it is tripping out on low discharge gas temperature. I have checked the system and the discharge temp is always above 115 F. I...
Well I have had problems with another building that we maintain that has a comm. link (Trane) from one building to another run underground so I am quite leery about doing that. When thunderstorms...
Thanks for the responce Sysint,
How many nodes in the new building?
Four split systems
How loaded down is the existing BCU?
Not at all, very open.
Its great to hear from you Sysint.
Do you want the BCU to do all the controlling?
Yes in as much a schedules and set points.
Do you want to use another vendors parts in the new building?...