Search:

Type: Posts; User: controltech01

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    319

    I am using PCLedit. Using the computer onboard...

    I am using PCLedit. Using the computer onboard com1 port. I have the port and baud rate set correctly but it is asking for a name of the site. Aything I put in there it does not like.
  2. Replies
    3
    Views
    319

    Backup Tracer L100 panel

    I have a old L100 panel that I need to back up. We can connect to it via hyperterminal and can go to the cassette backup but it doe not seem to do anything. We have PCLEdit software but cannot...
  3. Replies
    7
    Views
    742

    Problem Solved, Thanks!!!

    Hey guys, Thanks for the info. When I ohmed out the bus I did not pick up the EOL resistor. After 3 hours found loose connection on a controller. Having the ohm values helped. Once I fixed the...
  4. Replies
    7
    Views
    742

    Trane roaming comm failures

    I have a BCU that is only 2 years old that has had trouble since day 1.
    There are about 40 Lon cards model X1365C607-12J, on the link 1 of the BCU. There is a resistor across the bus wires at the...
  5. Replies
    3
    Views
    737

    Thanks to all

    I appreciate your help.

    Have a great evening.

    RC
  6. Replies
    3
    Views
    737

    New Tracker panel cable

    Hello all,

    Can anyone tell me the Trane part number for the cable to hook up my laptop to the new Tracker panel ???

    I have the Tracker software but have lost my cable.

    Thanks for any help....
  7. Replies
    8
    Views
    751

    What does the economizer have to do with the...

    What does the economizer have to do with the Supply Air Sensor?
  8. Replies
    8
    Views
    751

    Rtu's are Reliatel and the Tracker panel is a...

    Rtu's are Reliatel and the Tracker panel is a ver. 11.

    Not sure what version the CCP's are.

    Thanks,

    controltech01
  9. Replies
    8
    Views
    751

    Hello All, I have a Tracker 24 with 2...

    Hello All,

    I have a Tracker 24 with 2 Varitrack panels on it. One of the RTU's is giving me a "RTU2 SA Sensor failure" periodically. It has done this for over a year and has allways cleared in a...
  10. Replies
    6
    Views
    2,014

    These units probably came formt the factory with...

    These units probably came formt the factory with the novar boards in them.
    If you pull the comm buss off of these units it will maintain the last setpoints and occupancy that it was told to do by...
  11. Okay, I now know the difference. The radio...

    Okay, I now know the difference.
    The radio button for the ethernet is not selectable. It is grayed out along with the arcnet button. THe only options at IP/Bacnet and no connection.
    I even put...
  12. Do I have to set up the BBMD? If so what is the...

    Do I have to set up the BBMD?
    If so what is the default IP of the BCU?
  13. So I set it all up within Summit at the...

    So I set it all up within Summit at the workstation?
    This is what I tried the first time. I must have done something wrong.

    I went to "setup,communications,selected the job," It then brought up...
  14. I put it in and it does fit. Both TX and RX light...

    I put it in and it does fit. Both TX and RX light lite up when the computer ethernet cables are hooked up.

    I can not get the BCU configured using the IP validation tool. My serial connection...
  15. Hello Kwill or anyone else. My parts department...

    Hello Kwill or anyone else.
    My parts department sent me a ISA ethernet card for this BMTS and of coarse that is wrong. This is the only ethernet card they list for it. They are in touch with global...
  16. Replies
    16
    Views
    1,424

    Thanks to all for the input. I think I got the...

    Thanks to all for the input. I think I got the pitchure of the different ways to handle this.
  17. Replies
    16
    Views
    1,424

    Thanks Kwill- that is an option I may have to do....

    Thanks Kwill- that is an option I may have to do.

    Controldude- how can I get the 2 new UCM's on the network? Can they be put on the main comm loop?
  18. Replies
    16
    Views
    1,424

    This is an old CCP so I guess I am stick with the...

    This is an old CCP so I guess I am stick with the 16 zones. The 2 I am adding are on duct work that is allready there. Wild zones. So the air flow should be fine other than my bypass may not be big...
  19. Replies
    16
    Views
    1,424

    I have a customer with a Varitrac II CCP panel...

    I have a customer with a Varitrac II CCP panel that has 16 zones on it. They want to add 2 more zones. Can I do this? I found some documents that said I could only have 16 UCM's.

    Can I do a stand...
  20. Replies
    8
    Views
    1,046

    You have to drive all the boxes to 100% open on...

    You have to drive all the boxes to 100% open on MWU. I can't remember the exact procedure but if you have the edit screen open for the RTU on the page that you enable the morning warm up and hit the...
  21. I did confirm it does have chip version 4.0 so I...

    I did confirm it does have chip version 4.0 so I think we will just put the thernet card in. Got price from parts dept. sounded reasonable.
    MY customer also wants to quote to upgrade to SUmmit ver....
  22. The ehternet sounds like the way to go. Thanks...

    The ehternet sounds like the way to go. Thanks for the input and detail!!!
  23. I believe the transcievers are mixed in with the...

    I believe the transcievers are mixed in with the rest of the controllers. I will investigate adding a comm4 card.
    Since this problem is really not giving me any operational problems can I set up a...
  24. I have a building that has Summit ver. 11.01....

    I have a building that has Summit ver. 11.01. They have a remote building that utilizes 2- FSI D1200 trancievers to convert from the Trane Comm loop(RS485) to fiber optic. I have the same transievers...
  25. I have a customer that has Summit v11.01 and they...

    I have a customer that has Summit v11.01 and they needed to move it to a new machine. The new machine would not accept the old ISA Arnet Card. They purchase a PCI Arcnet card from the manufacturer....
Results 1 to 25 of 29
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event