Search:

Type: Posts; User: ScottG

Search: Search took 0.00 seconds.

  1. Replies
    24
    Views
    3,656

    York ISN Software needed ICE

    I have inherited a york connesys system and i have a dead contoller and i need ice to put the back up the customer has back in the new CX IDC.

    Thanks any help appreciated
  2. Replies
    13
    Views
    1,566

    The gauges are right of the suction and discharge...

    The gauges are right of the suction and discharge of the pumps both sets match pressures and they are top of the line glycerin filled gauges 0 - 200 psi. Gauges were installed by a previous...
  3. Replies
    339
    Views
    39,427

    As an ex field tech here is my 2 cents. After I...

    As an ex field tech here is my 2 cents. After I went to work for a union contractor, I made more money had better benefits and the type of work was large commercial work which I found far more...
  4. Replies
    13
    Views
    1,566

    I dont believe that this system had any expansion...

    I dont believe that this system had any expansion tank. I would think that the expansion would be insignificant in the temp range that the loop would experience in normal operation. 80 to 90
  5. Replies
    13
    Views
    1,566

    Tried this right after we checked for air pockets...

    Tried this right after we checked for air pockets and the pressure increases and decreases as described above. Why is the pressure returning to a normal reading when one of the stages is still...
  6. Thread: Honeywell VFDs

    by ScottG
    Replies
    36
    Views
    4,123

    There is only a hand full of drive manufactures...

    There is only a hand full of drive manufactures in the world, most of the products in the market are just one of these manufactures drives branded.

    I have used the Honeywell (Vacon) drives on...
  7. Replies
    13
    Views
    1,566

    Fluid Cooler Loop ----- strange pressures

    happy turkeyday all,

    Here is my problem. I just got home from a service call a customer called with some stange pressure readings on a closed loop fluid cooler. Fluid cooler servers 2 liquid...
  8. Replies
    6
    Views
    920

    Yes I understand that. And again thanks for the...

    Yes I understand that. And again thanks for the help it was just what I needed. It work perfectly. I was just curious if the property sheet was always valid because it was part of the database. That...
  9. Replies
    6
    Views
    920

    Thanks I will give that a try. So there they will...

    Thanks I will give that a try. So there they will not stale as they are not being polled?
  10. Replies
    6
    Views
    920

    They are bound to the JACE. maxflow minflow occ...

    They are bound to the JACE. maxflow minflow occ spts etc..
  11. Replies
    6
    Views
    920

    Lon points Stale

    Im sure this is going to be an easy question for somebody. I have an AX job that the Lon controllers have some points that go stale periodically. They will accept a write and will go valid again....
  12. Replies
    10
    Views
    2,529

    Converting DWG to floor plans for graphics

    Just curious what software is everyone using to make floor plan graphics from .dwg files?
  13. Replies
    6
    Views
    662

    Thanks for the thoughts viceman. The amount of...

    Thanks for the thoughts viceman.

    The amount of links that would be required to lead to all the graphics would make the home page too busy it would be crowded and cumbersome to use..Im looking for...
  14. Replies
    6
    Views
    662

    Cascading Menu for AX

    Greetings all,

    I have a request from a customer to build a interface that will allow access to any page from no more than two clicks. I thought that a cascading menu as you see on almost every...
Results 1 to 14 of 14
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event