Search:

Type: Posts; User: Old Soul

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Thread: Work Pants

    by Old Soul
    Replies
    52
    Views
    4,905

    http://www.lapolicegear.com/51174251.html I wear...

    http://www.lapolicegear.com/51174251.html
    I wear these or Carharrt B159. We have to wear 100% cotton due to NFPA 70E an these are the best options I have found. Company provides us with Dickies...
  2. Replies
    9
    Views
    787

    The baking soda is a good idea. Whatever you do...

    The baking soda is a good idea. Whatever you do when the coil is clean I would change the filtration. I have a textile plant that I look after with (4) 130 ton RTU's and with standard 2" pleats they...
  3. Replies
    8
    Views
    542

    If the water flow is indeed what has eaten up the...

    If the water flow is indeed what has eaten up the tube sheet it will do the same with the gates if they are left like that. If there are any circuit setters in the loop he could adjust them to get...
  4. Replies
    14
    Views
    1,201

    Get at least 2. On larger systems you'll need...

    Get at least 2. On larger systems you'll need them. Or you may need to leave one on a system and find on the next call you need one. One of the handiest tools in my truck!
  5. A lot of good points here. One big sticking point...

    A lot of good points here. One big sticking point that I have seen though is that we have nobody new coming into the industry. At least in our area we don't , maybe it's different somewhere else. I...
  6. Thread: RTAA EXV

    by Old Soul
    Replies
    11
    Views
    662

    Just a thought but you may be able to find...

    Just a thought but you may be able to find somebody locally that is scavenging parts off of machines that are being decommissioned. We have stockpiled some parts from the RTAA machines as they are...
  7. Replies
    228
    Views
    44,536

    They tried to bill me for minutes used on the...

    They tried to bill me for minutes used on the company phone, a charger that was actually in the truck, and hold my last check. The instances that a check can be held in NC are very specific and a...
  8. Fluke. End of discussion. Bad experiences with...

    Fluke. End of discussion. Bad experiences with Fieldpiece and UEI both. I have a Fluke 29 that I know is over 15 years old and still works great. 2 year Fieldpiece that isn't worth the effort it...
  9. Replies
    31
    Views
    2,421

    Cracked heat exchanger is easy. Disable it and...

    Cracked heat exchanger is easy. Disable it and done. Document it (pics if possible) and notify the customer. Three people died last year in NC due to malfunctioning equipment.
  10. http://www.planomolding.com/product.php?BCCID=108&...

    http://www.planomolding.com/product.php?BCCID=108&PID=705

    I carry this one every day in my Tech LC bag. You can pick these up at WalMart. Works pretty good.
  11. Replies
    19
    Views
    1,807

    You probably won't find an aftermarket one to...

    You probably won't find an aftermarket one to match up. You can get fairly close though. If your system has a TXV you will probably be ok. Will the system be right, no it won't but it will be...
  12. Everything he said except you will need SAE and...

    Everything he said except you will need SAE and Metric tools and a helper to carry your tools! Just kidding about the helper but with the newer equipment you will need Metric tools. Gearwrench makes...
  13. Replies
    9
    Views
    656

    You always have questions. I do anyway. Knowing...

    You always have questions. I do anyway. Knowing the answers counts for very little for me. Knowing where to get the answers is what is important. My opinion but I would make the move as long as it is...
  14. Replies
    12
    Views
    1,495

    According to what you're doing. Chiller controls...

    According to what you're doing. Chiller controls is Techview, BAS is Rover or TU but according to where in the network you connect you could probably get by with Rover.
  15. Replies
    23
    Views
    2,304

    I remember those days. Graduated school and...

    I remember those days. Graduated school and thought finding a job would be a breeze. Six months later took a job for half of what I thought I would be making and driving my own truck to work every...
  16. Replies
    23
    Views
    2,911

    Poll: I would recommend Mitsibushi. I like the way they...

    I would recommend Mitsibushi. I like the way they handle the take off to the individual air handlers better. Contact a local rep and ask for a site tour. Ronald McDonald House in Winston has this...
  17. Replies
    15
    Views
    2,138

    http://electricalnotes.wordpress.com/2011/03/23/wh...

    http://electricalnotes.wordpress.com/2011/03/23/what-is-corona-effect/

    Here is some reading. You can go on from there. As older drives start failing my belief is this will become more common. Good...
  18. Replies
    15
    Views
    2,138

    How long are the cable runs from drive to the...

    How long are the cable runs from drive to the motors and is the ground derated for the circuit. We have a site where we have lost drives and motors both with cabling issues.
  19. Replies
    34
    Views
    4,299

    Been carrying the Terralux but have now switched...

    Been carrying the Terralux but have now switched over to Streamlight ProTac lights. Still carry the HCRI model Terralux because it allows me to see colors better.
  20. Replies
    34
    Views
    2,921

    Eyes, ears, fingers and toes guys! Don't get out...

    Eyes, ears, fingers and toes guys! Don't get out of the truck without them. I have every intention of going home in the same shape I left. That injury will probably need skin grafts and a good while...
  21. Replies
    7
    Views
    1,923

    Deep fried in peanut oil only way to go!

    Deep fried in peanut oil only way to go!
  22. Replies
    8
    Views
    859

    I have switched over to the black hoses a couple...

    I have switched over to the black hoses a couple of years ago. Better for pulling a vacum through and tougher day to day. Harder to handle though so there is a trade off.
  23. Replies
    24
    Views
    2,493

    What he is telling you is to get into a union...

    What he is telling you is to get into a union training program. I don't have any experience with a program like that but have been told that they have the best training in the industry. I went to...
  24. Thread: road rage

    by Old Soul
    Replies
    39
    Views
    3,855

    Been there. Working at a mall many moons ago and...

    Been there. Working at a mall many moons ago and got done with my job. Wrote up my ticket and couldn't find the manager, found here in the back of the stockroom servicing a guy. I turned and headed...
  25. Replies
    46
    Views
    5,503

    Don't forget getting stepped on! A friend of mine...

    Don't forget getting stepped on! A friend of mine that does a lot of resteraunt work told me always keep your heels to the side while working on your knees in a kitchen so your ankles don't get...
  26. Replies
    7
    Views
    863

    We used to take care of a facility that had a...

    We used to take care of a facility that had a fairly high concentration of sulfur dioxide in the air along with who knows what else. When a new rooftop machine was put in the would send them down to...
  27. Replies
    37
    Views
    2,965

    Lots of good advice so far. I wish somebody had...

    Lots of good advice so far. I wish somebody had mentioned kneepads to me about 20 years ago. You don't need to carry as many tools with you as you think, your back will thank you as you get older....
  28. Replies
    60
    Views
    4,357

    Something to consider before retrofitting this...

    Something to consider before retrofitting this machine. An upfit like this could very well affect the UL listing of it and if some sort of failure occurred causing injury or property damage the...
  29. Replies
    10
    Views
    1,554

    :grin2:I doubt you'll see a micro groove copper...

    :grin2:I doubt you'll see a micro groove copper coil due to expense. The going way of doing things today is cheaper, cheaper, cheaper. Also the heat transfer of the aluminum coils will keep them in...
  30. Replies
    46
    Views
    5,503

    :gah:The older I get the less I like to have...

    :gah:The older I get the less I like to have people around me while I'm trying to work or talking to me. The phone ringing upsets me sometimes!
  31. Replies
    13
    Views
    1,213

    Just make sure you don't mix oils and you'll be...

    Just make sure you don't mix oils and you'll be fine. I always bleed my gauges off after using them and purge them with nitrogen before using them on a system with a different gas.
  32. Replies
    26
    Views
    2,098

    Been burned, cut, bit, stung, shocked, pulled...

    Been burned, cut, bit, stung, shocked, pulled muscles, torn ligaments, heat stroke and more in my career. It physical work and sometimes in incredibly dangerous locations. You have to always be aware...
  33. What they said. The tape won't hold after a...

    What they said. The tape won't hold after a while. You can use some mastic to seal it this way and. Have done this at times to insure a seal in the connection in areas that were hard to access any...
  34. Thread: NO AC CALL

    by Old Soul
    Replies
    23
    Views
    3,624

    Your right on the money Ryan. Not much of a...

    Your right on the money Ryan. Not much of a benefits package in scrapping!
  35. Thread: NO AC CALL

    by Old Soul
    Replies
    23
    Views
    3,624

    They are making less scraping than at a honest...

    They are making less scraping than at a honest job. When you figure the hours that go into surveying sites, most work is done at night so that is overtime rate, breaking machines down for scrap,...
  36. Replies
    33
    Views
    3,880

    A local deputy told me that if he stopped any...

    A local deputy told me that if he stopped any truck with a couple of shady guys in it the first thing he was looking for was a battery powered saw. Said if he saw that they were always good for a...
  37. Replies
    83
    Views
    6,516

    It gets fairly warm here in N.C too and the add...

    It gets fairly warm here in N.C too and the add on condensers really help. The next time you use your machine try it with a bucket full of ice water instead of just water. I keep an old cooler just...
  38. Replies
    36
    Views
    3,623

    Many moons ago when I was still gourd green I...

    Many moons ago when I was still gourd green I found a compressor contactor with a bad coil. Found it within minutes on a Carrier package unit. Thought to self oh yeah I got this! This heating and air...
  39. Replies
    15
    Views
    1,662

    You did the right thing. If the job was bid that...

    You did the right thing. If the job was bid that tight that's even more reason to make sure it is done right. I hope they are not in the habit of taking in work at a loss for your sake.
  40. Replies
    16
    Views
    3,862

    I would start with a data logger on the incoming...

    I would start with a data logger on the incoming voltage and work my way to the drive from there. We have the Supco setup and used it with good results before.
  41. Replies
    12
    Views
    1,254

    Our local Grainger has one and it works great! I...

    Our local Grainger has one and it works great! I can see where proper mounting would be very important .
  42. Replies
    228
    Views
    44,536

    Pulled my time with that bunch as well. Put...

    Pulled my time with that bunch as well. Put 40,000 miles on a van in 6 months time and worked 60 + hours every week. Was expected to find a " pm add " on every job to cover driving time to the next...
  43. Thread: Tool bags

    by Old Soul
    Replies
    96
    Views
    17,975

    5.11 bail out bag. Carries what I need for most...

    5.11 bail out bag. Carries what I need for most every job and if it's not in there I know what I need from the truck.
  44. Thread: Leatherman

    by Old Soul
    Replies
    20
    Views
    2,049

    Don't forget need to get to the tools from the...

    Don't forget need to get to the tools from the outside! Love my Leathermann but get tired of having to open it to get to what I want.
  45. Replies
    118
    Views
    14,954

    Went to community college and started at 21 in...

    Went to community college and started at 21 in the field. Thought this would be great getting to work where it is warm in the winter and cool in the summer:( Boy was I wrong.
  46. Replies
    7
    Views
    630

    Blue Ant. You can find them cheap on Amazon or...

    Blue Ant. You can find them cheap on Amazon or they sell them in the store at Best Buy now. I have tried several different brands and they have been the best ones. Washed and dried my last one three...
  47. Replies
    23
    Views
    2,181

    If your company doen not have a safety officer to...

    If your company doen not have a safety officer to asses this and your manager will not back you up it is a pretty easy call. Find a shop that cares about you. Decent techs are hard to find around...
  48. Replies
    11
    Views
    3,405

    Friend of mine works for them. He likes it and...

    Friend of mine works for them. He likes it and the pace is a lot calmer than working in the field and for about the same money. Only thing is that it is a contract position. But at least you know...
  49. Thread: detek select

    by Old Soul
    Replies
    7
    Views
    977

    I have one about a year old and have used it for...

    I have one about a year old and have used it for 407C with no problems
  50. Thread: Weather sucks

    by Old Soul
    Replies
    14
    Views
    1,389

    Got one in my van right now. Also have a good...

    Got one in my van right now. Also have a good size tarp in a five gallon bucket ,because I can never fold them back up with some bungees for days like yesterday where there is not enough room to set...
Results 1 to 50 of 73
Page 1 of 2 1 2
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event