Search:

Type: Posts; User: coolingitrite

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. at least the paint wont fade as fast

    at least the paint wont fade as fast
  2. Replies
    20
    Views
    1,098

    good advice. clean machine. don't know bout...

    good advice. clean machine. don't know bout florida but back in san Antonio tx, lots of calcium....... cleaning (descaling) twice a year
  3. Replies
    20
    Views
    1,098

    also raising the float will make it smaller but...

    also raising the float will make it smaller but may also affect how the ice falls. I mean with the cubes weighing less..
  4. Replies
    20
    Views
    1,098

    I would think this would cause problem on both...

    I would think this would cause problem on both sides, but, did you check to ensure that bin stat is opening when ice hits it and shuts the unit down so ice does not back up into evap
  5. Replies
    20
    Views
    1,098

    could make a good cube but not harvest properly

    could make a good cube but not harvest properly
  6. Replies
    20
    Views
    1,098

    I agree sounds like may have separation on that...

    I agree sounds like may have separation on that evap. ice did not drop properly during harvest and built up. seen them with waves in it if you look down or evap moves if you grab a grid and tug on it
  7. thought about it afterword. after I typed it. got...

    thought about it afterword. after I typed it. got that whether it be r22 404 or 410 with a dirty condenser would have be 6 one half dozen.. I have not seen any units with 410 in them...
  8. I assume u mean on a non-blend.. how do you get...

    I assume u mean on a non-blend.. how do you get close and then go vapor. then doesn't that mean that the refrigerant coming out of the tank in vapor once you start charging it vapor in for ex 404a no...
  9. only saying that 410 already runs a high pressure...

    only saying that 410 already runs a high pressure and since most kitchen equipment is not maintained as far as coils, etc. would just compound that.. just sayin. probably looking at it wrong
  10. Replies
    21
    Views
    1,948

    could go back to condensing unit manufacture and...

    could go back to condensing unit manufacture and ask them. with a headmaster, they should be able to tell you how much refrigerant to add just after the sight glass fills to insure you are charged...
  11. 410 in ice machines? with condenser coils sitting...

    410 in ice machines? with condenser coils sitting in a greasy kitchen with no maintenance? nope, don't like it
  12. isn't there a spec plate or info like...

    isn't there a spec plate or info like manufacturer with model and serial you can use to find out what the correct charge was for r12. i believe hotshot if i remember right was 80% of original charge...
  13. Replies
    13
    Views
    1,050

    I agree, whenever I replace a compressor, I...

    I agree, whenever I replace a compressor, I always change out the start components. start component on a three phase being the contactor. In my opinion, better to be safe then sorry. Seen it before...
  14. Replies
    13
    Views
    12,020

    thanks for the info

    thanks for the info
  15. Replies
    13
    Views
    12,020

    kinda don't want to go into why i don't know this...

    kinda don't want to go into why i don't know this but when setting the pressure control (fan cycling) for a particular refrigerant, how do ya figure the set points. (cut in cut out) does it have to...
  16. Replies
    9
    Views
    596

    looks like suicide to me. cas closed

    looks like suicide to me. cas closed
  17. Replies
    23
    Views
    1,312

    i agree that most electricians have problems with...

    i agree that most electricians have problems with wiring diagrams but when i took a break from the hvac field for a bit to go to work for my brother i law doing electrical, i was running pipe for...
  18. Replies
    8
    Views
    1,474

    your welcome

    your welcome
  19. Replies
    8
    Views
    1,474

    try this number 830 997 2691. they might be able...

    try this number 830 997 2691. they might be able to give you info on contacting tech support, but they are probably going to want some info on the company that you work for. where in texas r u
  20. Replies
    8
    Views
    1,474

    call groen tech support. tell em who you work...

    call groen tech support. tell em who you work for. they should be able to walk ya through it
  21. Replies
    8
    Views
    1,474

    oh my bad when you said "we have a steamer" you...

    oh my bad when you said "we have a steamer" you sounded like the end user
  22. Replies
    8
    Views
    1,474

    call for service. where at in texas?

    call for service. where at in texas?
  23. Replies
    60
    Views
    3,833

    if the job is done wrong it does not matter what...

    if the job is done wrong it does not matter what you put in. i have installed quite a few of the coleman. have bot seen anymore problems with that brand compared to others.
  24. Replies
    44
    Views
    2,592

    call a pro in your area...

    call a pro in your area...
  25. Replies
    17
    Views
    3,307

    i read the tread wrong. ok if this is like a true...

    i read the tread wrong. ok if this is like a true freezer i have seen them with out the pressure switch. but don't these at least have a cpr valve (well most of the larger reachin-so unit does not...
Results 1 to 25 of 101
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event