Search:

If there is anyone out there that could help me make a couple backups using xPSI let me know. Could use a little help to get this done.

I have alwyas started my addressing at MAC 5. One basic reason is that any new software configurable controller that gets added will ususally come out of the box lower than that, and will be...

Thanks hvacpilot! I do believe the tec2100 file is the one that i needed. I am going to verify this.

thanks again!

I am in search of a prn file for the Johnson 2000 series TEC thermostat.

Is there anyone that might have this they would be willing to share?

Thanks
Matt

So what you are asking to do is create a graphic and then use this for multiple systems? If this is the case you have to make sure that you have the exact same naming on the points in each controller...

I have to agree with this. The systems are all talking Bacnet or Lon, but anytime that you are forced to go to a supplier, it has to be considered proprietary. This is why the school district I work...

There are other DDC editors built into the Envision program that can be used, but they are not as user friendly as Visio. You can upload the DDC to Visio but you are correct that the blocks are...

The Jace or NAE will work to program and setup the controllers IF you have Envision for Bactalk.

That is a 5831 and a 5801. Its possible that the variables were never named. I will hunt around and see what i can find.

The points live in the individual Tux-Vav controllers and will come through.

I have a manual that will give you all that you need. You will have to add you email to your profile so that i can...

All of the items that you list are no longer made, but you can intrface and get the data out of them but you will need a BCM-Pwr, BCM-Eth, and BCM-Tux.

There is a zero cutoff and a calibration factor. I dont have the info in front of me right now, but will see if i can find these points for you.

I dont know why you would need a Spyder license for an Alerton controller, but you can get into balance mode on the microset ( If Installed). Otherwise there are only a couple points that you need to...

Sure thing!

You can pulse the inputs, but you do not have to. It also works if the inputs come on and stay on. Reset input has the highest priority and will override the set input.

Simulate by turning on the...

Sorry I thought that would come through. This one is done with two or blocks. Not the outputs of the two blocks. Set is the top input and reset is the bottom. I will try to clean up the image and...

http://hvac-talk.com/vbb/attachment.php?attachmentid=450781&d=1388666649


THis is a good way to build a flip flop also

Do you have an XOR block ( exclusive or ) Link the out of the xor back into an input. This will substitute for the last value block.

I have done alot of work on ALerton systems in Iowa in the past. If you email me i should be able to help you out.

This is good to know. I had originally though that any Jace could be licensed to add Spyder and have the ability to program. I did not know that Honeywell's position is that you have to spend x...

MazdaJoe, Could you tell me who you stated that you are not supposed to use the rate limit block? I would agree with this statement because you should be able to slow the pid to accomplish the same...

I would also try getting rid of the deadband completely. Let the PID always have control of the firing rate.

http://hvac-talk.com/vbb/attachment.php?attachmentid=440691&thumb=1&d=1342711228


Take a look at this photo and you will realize that the Spyder Learning Curve is way to long to discuss the...

Reckles,

Is this installed on a VM?

Deepest sympathies go out to you and your family.

432761

This is the proper way to install a Jace, I guess?

One other thing to look at is this. In the Venom apps, if you look you will see that they use a cycler and stager, set them up the same and take the lower of the two. I can't remember but i think one...

Chuck,

Get in touch with me. I think that i can help you out. My email address is in my profile

Matt

I would say sell it, but as soon as you do there will be a new Spyder tool and then you fix will probably be no good. :(

I had this issue once. It was a Mcquay chiller with a Lon controller though. The issue that i discovered was the electricians when installing my 1" conduit to the chiller for the Lon bus, laid it in...

When i bring controllers in across multiple MS/TP's into the same system i use a numbering scheme that adds the network number to the mac address. Mac 1 on Network 2000 = 2001, Mac 1 on Network 2100...

Also 127 is an addressing limitation. I am sure if the unit loads are calculated that trunk would be overloaded.

Most of the manufacturers that i work with say 65 controllers per comm line.

BAM! Old school Subroutines. I used to love these for controlling multiple controllers.

Yep forgot to mention that they may have this buried in a Subroutine.

Well to get the input setup correctly happens by clicking the controller located in the lower right hand corner of the first Visio page. The things that you may have to look out for is if the reading...

Does anyone have a points list, and could tell me what point i need to link my schedule to in niagara?

I have witnessed this many times. It has happened to me on more that just compare blocks. This is why i have started to add override blocks before any compare blocks. There are others that i have...

If they are Bactalk controllers then they are Bacnet and will pull right into the Jace, if you have the Bacnet MS/TP Driver. When you discover the points, you will notice that they pull in as the AV...

One has the Actuator integrated with the controller. The other is controller only.

There is not one that i am aware of. You still need to program the controllers using the Ebt Platform and then add the controllers as a dynamic device on the Ax Platform.

What versions are you using? I had this problem and sent a copy of my station to HW for them to look at.

This is the version that i have been using. Its been solid for me up to this point.

Let us know what version of the Spyder tool you are using. There are many different errors that you could encounter based on the tool.

Yes, under the link tab you can set the device as a Standard IP Device, BBMD, or Foreign Device.
If you set it as a BBMD, the BDT table is also accessible from here to add your other BBMD's

There is a new one coming out in a couple weeks FYI. 5.204

So the picture you show looks like its from the Siemens line. Maybe a 134-1511.

Here is a few lines from the install guide that comes with that. Most people do not realize that you want as much...

JENE = Java Enabled Network Engine. Its a privately labled Tridium Jace with expanded I/O that Lynxspring has programmed for AAON.

I have some used controllers that i could sell. My email is in my profile. Send me an email to discuss.

The Balancer will give you the setpoint, and yes it needs to slow down.

Good Choice.

This does not make it any tougher to do the swap. You will not need the Ibex points any longer, so they can go away. If they are application specific you will not need most of the global ddc, which...