Search Results - HVAC-Talk: Heating, Air & Refrigeration Discussion

Search:

Type: Posts; User: oshimi15

Search: Search took 0.01 seconds.

  1. Thread: JCI

    by oshimi15
    Replies
    11
    Views
    1,386

    JCI is at it again... Look for another company...

    JCI is at it again...
    Look for another company to be bought******
  2. Replies
    5
    Views
    895

    Why don't you use the UNOCC mode all the time....

    Why don't you use the UNOCC mode all the time.
    This way you can setup UNOCC setpoints and the fan will
    cycle according to UNOCC setpoints.
  3. Thread: XT-9100 help

    by oshimi15
    Replies
    2
    Views
    729

    On the XP --do you have AI jumpers set for voltage

    On the XP --do you have AI jumpers set for voltage
  4. Thread: JC/Mammoth

    by oshimi15
    Replies
    4
    Views
    1,128

    If you are metasys to just view the controller...

    If you are metasys to just view the controller then you
    should be OK. We were letting the metasys start and stop
    the 100% OA unit but upon startup the unit would lock itself out and there was...
  5. Thread: JC/Mammoth

    by oshimi15
    Replies
    4
    Views
    1,128

    YES, unfortunately. NOTHING but trouble..DON"T...

    YES, unfortunately.

    NOTHING but trouble..DON"T DO IT!!!!!!!!
  6. Replies
    2
    Views
    733

    Also, if you are using a Local Setpoint instead...

    Also, if you are using a Local Setpoint instead of a ACO that can burn your EPROMM and you would have to replace the DX. But I would try to add another Loop first.
  7. Replies
    36
    Views
    3,663

    I am from Illinois and rumors were around last...

    I am from Illinois and rumors were around last week but
    my supervisor confirmed it yesterday. Although he
    wouldn't be specific other than saying mechanics will be performing rep 1 and 2 work (PMs)....
  8. Replies
    36
    Views
    3,663

    x-wrenchturner---where are u from? There are...

    x-wrenchturner---where are u from?

    There are rumors flying around the branch
    about mechanics getting computer classes but nothing was said about them doing any tech work.
    There are other rumors...
  9. Replies
    6
    Views
    894

    I am working on a Carrier Chiller right now and...

    I am working on a Carrier Chiller right now
    and we have a LON card connected to CCN just
    to get Chiller Info then we have local Lon controller
    for Chiller ON/OFF logic. I recommend this solution...
  10. Replies
    2
    Views
    1,353

    Do you have a workstation? If so take the...

    Do you have a workstation?
    If so take the battery(top right corner) out
    cycle power on NC...
    it should get download from workstation.
  11. Thread: Info needed

    by oshimi15
    Replies
    2
    Views
    1,017

    thanks special ed

    thanks special ed
  12. Thread: Info needed

    by oshimi15
    Replies
    2
    Views
    1,017

    Can anyone give me the capacity of the following...

    Can anyone give me the capacity of the following furnace?
    Comfortmaker Synder General
    Model# GUF100A012AN

    Also the tonnage of the following condensor?

    Kenmore Hi Efficiency 5000
    style#...
  13. Replies
    25
    Views
    3,116

    the above plan is replacing their little...

    the above plan is replacing their little geographical teams
  14. Replies
    25
    Views
    3,116

    JCI Service Dept has a new theory on service....

    JCI Service Dept has a new theory on service.
    Illinois will be rolling out the Milwaukee's
    pilot program and then everyone else.
    Something like vertical market scheme that failed
    but mechanics...
Results 1 to 14 of 14
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event