Search:

Type: Posts; User: 408-COUPE

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    766

    Amen to that. Just plugged her up and it works...

    Amen to that.
    Just plugged her up and it works flawless of course.
    Thanks again for the help. Almost had to retire on that one.
  2. Replies
    7
    Views
    766

    Awesome. I Feel like an idiot. I read the manual...

    Awesome. I Feel like an idiot. I read the manual on the job but of course that part did not catch my eye at all. Thanks so much.
  3. Replies
    7
    Views
    766

    New circuit board has me confused.

    Came to my first call today and diagnosed a bad circuit board not giving 24v to the gas valve. All operations worked fine with old board. Inducer, pressure switch, hsi but no valve.
    Old board is a...
  4. Replies
    9
    Views
    739

    YUP. 2 Ruuds in the same day last week. Customer...

    YUP. 2 Ruuds in the same day last week. Customer got to watch on the second one when I took the door off, touched the pressure switch and unit came right on. Cost rica special.
  5. Had a problem like this occur on a trance unit...

    Had a problem like this occur on a trance unit but less frequent. Problem turned out to be a loose pin connection inside the molex plug for the hsi. Would do it randomly and was a headache to figure...
  6. Replies
    54
    Views
    2,406

    Glad you found the problem.

    Glad you found the problem.
  7. Replies
    54
    Views
    2,406

    If not already mentioned, secondary heat...

    If not already mentioned, secondary heat exchanger could have water in it. Something could be blocking the flue as well.
  8. You will most likely be changing out the circuit...

    You will most likely be changing out the circuit board. We see it all the time on goodmans, acts like the flame sensor, gas valve, pressure switch etc. what you need to do is right when it starts...
  9. Thread: No superheat

    by 408-COUPE
    Replies
    28
    Views
    2,681

    One of the biggest things that help is writing...

    One of the biggest things that help is writing everything down. My mom told me to do this at a young age, never did until i started working full time for my fathers business. Just make it a habit...
  10. Replies
    118
    Views
    14,097

    Started at 6 years old working for my dads...

    Started at 6 years old working for my dads company in the summers, im 22 now. Hated it for a long time, didnt know what i was doing and my dad was real hard on me. Worked till 11 o clock at night...
  11. Cant wait to tell a customer that.

    Cant wait to tell a customer that.
  12. Replies
    19
    Views
    1,718

    Bingo. Anytime I have the opportunity to show the...

    Bingo. Anytime I have the opportunity to show the customers the problem whether it's the heat exchanger, fan motor, circuit board I do it. Seeing is believing. Especially in this business. The trust...
  13. Replies
    26
    Views
    2,162

    Excellent post. In the old days my uncle worked...

    Excellent post. In the old days my uncle worked for a company who would pay someone to clean YOUR truck if you didn't..
    I can't tell you how many times I've went on our other techs trucks and...
  14. Excellent walk through. I paused after you wrote...

    Excellent walk through. I paused after you wrote the problems and first thought problem with the office, then said hmm maybe the company's put in 22 lol. Job well done keep up the good work.
  15. Replies
    14
    Views
    1,454

    Had to use dye a couple times. If you do wind up...

    Had to use dye a couple times. If you do wind up using it make sure you dont wait more then 48 hours or so to check for it. I had a busy summer and left it for a week, i found the leak on the evap...
  16. Replies
    20
    Views
    2,002

    Lol lol

    Lol lol
  17. Replies
    36
    Views
    4,283

    Does anyone see this causing call backs because...

    Does anyone see this causing call backs because of the way it works and the customer not fully understanding how?? Or just causing problems in general? Just me.
  18. Replies
    39
    Views
    2,762

    After this summer i have concluded that a bad run...

    After this summer i have concluded that a bad run cap is the best thing that ever happened to a dishonest company. Bad run cap=bad compressor. Its unfortunate but happens all the time im sure. We had...
  19. Replies
    7
    Views
    894

    Call the company back

    Call the company back
  20. 1. Install would have taken 1 and a half days max...

    1. Install would have taken 1 and a half days max for our company. Honestly i think you are being pretty generous with your concern (Although i dont know what all has been said to the Company). The...
  21. Replies
    14
    Views
    713

    What were the temps out of the supply vents when...

    What were the temps out of the supply vents when you were there, or did you even have time to get them before the compressor shut off?
  22. Replies
    14
    Views
    713

    Put the head pressure at 300, give it a day and...

    Put the head pressure at 300, give it a day and see what it does.
  23. Replies
    29
    Views
    2,017

    Thats a fair price. How much do you think it...

    Thats a fair price. How much do you think it takes McDonalds to make a Big Mac? What do they charge? Do you see where i am getting at? You pay for the overhead, insurance, gas, payroll, and God...
  24. Replies
    69
    Views
    6,636

    We have installed well over 50 Goodman condenser...

    We have installed well over 50 Goodman condenser units in 2010. Had 1 compressor failure so far but thats about it. One thing we started to do is relocate the contactor about 2 inches up so you dont...
  25. Someone tried to do this at my Church with one of...

    Someone tried to do this at my Church with one of our 50 ton units back in November. After they started sawzalling and realized the coil was 5 inches thick they said forget it. Only got about 2...
Results 1 to 25 of 109
Page 1 of 5 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event