Search:

my friend has a house in Ossining NY -1,500 sqft -he has a gas furnace that he ripped out
seperate water heater --
wants a boiler --w-baseboard --looking for someone in Westchester who knows what...

you need to go somewhere else --the coils i bring back are limed inside and dirty outside --fittings with solder are considered dirty --you need to cut them at the joints and seperate it or unsweat...

at $2.60/lb for copper scrap ---hell yeah i make $260 a week on average with scrap .(brass,copper,cast iron and tin) the past few weeks i have been replacing water to water domestic coils for...

i had been in contact with Ray but they weren't sure if they could still have them made ---they had no sources --and non in stock --i did finally get an answer from them they will make me a few ...

i work on dinosours --i have an old Ray burner that i'm working on the fiber gear that turns the oil pump is in bad shape --the burner is an aeop-144 size 125 --the gear markings are celeron 1084...

yes its very common with 2 boilers without check valves on the header --or not having an equalizer in the rear the Lag boiler steam will condense and overfill

there is no reason for 2 pipe and if its an outdoor tank you will have a hard time moving enough oil in the very cold days -if you dont know how to prime and bleed an oil pump leave it alone --it...

i have found new old stock 1 tube only and 1 tube with the holder --i was wondering how i can test these without installing them and is anyone still in the market for these??

.

[Edited by oil-2-4-6-gas on 12-16-2005 at 10:53 PM]

Yea um you do understand when you click that link they are talking about the company that went in to fix these issues --and posted the pics

what is the make and model of your fill valve-sounds like a taco -and typically all manufacturors like to see 12 psi as a minimum

has anyone dealt with the low nox Limpsfield reto-fit burners--exhaust gas recirculation --was at a job today they were almost done with the first of 3 burners going in--replacing 2 Cleaver Brooks...

what is the static fill pressure for your house supposed to be --how high is it from the boiler to the highest emitter--baseboard,radiator,or coil + ? you most likely are not turning the adjustement...

there is no reason to have wire nuts in a panel that size --everything else looks neat --but the wire nuts and tape --do not belong in a new panel.

ecm motor extremely.costly.motor. control on the motor

thats the way to do when the a/c guy gets there give him a hard time,bust his balls --i hope he treats you like i do with my heating customers--nothing we like more than a pain in a$$ customer...

Roman do a search using the words Fluke or Fieldpiece --this subject has been beaten to death -------i use a Fieldpiece myself for general use --but i do have a few other meters ,Amprobe the old...

they tax 2% in westchester n.y. --

we"ve had Nextel for 6 years --service was touchy but in the past 3 years most problem areas have towers now --the best part is being linked to supply houses --i do commercial and it can be tricky...

same here years of eyeballing flames --before using the analyzer // # 1 set-by eye # 2 smoke test # 3 analyzer

steam stop? non return valve? ---- shutoff valve,,check valve all of your upper tubes are wet the valve is leaking above it --i guess depending on what part of the business and country you live...

how long was the boiler off and empty for? looks like your king valve is leaking a little --sadly that looks like the typical C.B. boiler tubes we see--that seems to be the one brand we do annual...

))))))))I don't know about Webster, but the Suntec PRV38, which is essentially the same valve, only requires that the vent hole be down when there is a chance that wate can get in there.)))))))))))))...

dirt bikes-go-carts,minibikes(homemade)-owned many from 80 ke-100 Hodaka road toad can-am 250,400 rm 370 older Cz 250(what a pig)and more --riding 1995 cr 250 for the past few years have yet to...

it makes for a nice lunch after hitting the scrap-yard

if you are cutting and threading make sure you ream it --remove all shavings,clean any and all oil residue on the pipe --not just letting it "drip out" but wash the inside of the pipe---nothing...

replaced many blown-out burners - most common reason is the intake screens getting dirty -- Lochinvars' filter on the intake will not change this issue {most will not be changed on a regular...

you might have yourself an even bigger problem if you get your compressor and you use too much pressure --anyway if your tank is over 30 years indoors its time to clean it-have it tested, replace the...

not for long with the relief valve plugged ----whats your address i would like to submit a bid--with your "estate" rebuilding your house and replacing the heating system --seriously though -with the...

what Fireye control do you have -is it gas oil or comination--

i'm on call Sunday:::you call i will tell you on the phone the rates, the minimum for the service call.sunday can't get parts if it's a board or a non-stock item, i will advise you that i fix it or...

just fill it with the well water --the sediment and crap will be boiled out of the water as long as there are no leaks you have no problem/ or if you really want to fill the boiler with distilled...

Powerflames are great burners until someone touches the pilot ---i'd check the pilot ,electrode,transformer,high tension wire, regultor and make sure the pilot assy is sitting correctly in the...

you should come to NY and checkout some of the panels and set-ups out here most of the control problems end up being at Schools {low bid situations} come to think of it most were installation or...

i have changed many of them -------they never blowout like that without some warning signs for a good period of time --ie..bubbles in the outer shells' paint small accumulation of sediment in...

thats funny i call the control guys all the time --after i get the system running and over-ride or by-pass their control and they all try to tell me "its definetly not a control problem " then i...

hot water /steam doesn't matter --tie a relay in to break the limit circuit before going to the flame safeguard relay --use that circuit to power relay coil to operate your dampers --return the...

..

[Edited by oil-2-4-6-gas on 12-04-2004 at 07:36 PM]

i work with a mechanic who's father was the rep for them --he was brought up on them what's you're location

That's old---

there has to be a rating plate on the vessel--the relief valve should be what the vessel is rated for not your running pressure ---

pitch toward a valve --(this will not be your suction but a service valve ) install a floating suction line --use a mix of kero in the winter every season in the fall purge the tank of some of the...

how is he testing the transformer --r-c or each leg individually to ground

a little of the old #7 Jack--green or black label and any cold beer will do

i got my a@@ reamed out because of it// they were threatening to have me arressted if i don't return the parts and put it back the way it was --- so i put it back --and called In Con-ED i believe...

i went to a laundramat today they have a Natco tankless hot water maker -relief valve leaking water --found the manual-fill open closed it off and started draining--well i was looking around found...

i dont mind most customers who like to hang around and ask questions i do a better job sometimes -explain a lot of things to them but there are those customers who just complain about previous...

peck vent

tell your supervisor to go f@#^% himself --give me some quality workers with their own tools, and pay you enough to take the responsability of lead installer --and your old-man counterpart--tell him...

come'on guys he just has that famous --balanced Armstrong muffler bearing once you start it she nevers stops----perpetual motion at its finest --hats off to Armstrong