Search:

I know your new here but this thread is like 18 years old let be please start new threads or reply to newer threads any way welcome to HVAC talk

I read his profile just now I think him and phm shouldn’t be left alone unsupervised :grin2:

My guess it’s using in between the studs to the crawl space or ont other side of the wall like office trailers. Either way that’s got to noisy you would think

You might hit the black triangle and have the mods move this to the junkyard that’s the buy, sell area of this forum

We were slow last week so I got to recover gas from the boneyard and found these

I’m no expert but I thought they were supposed to be on the neutral side of the system and were pre charged to 19psi which was the standard pressure of a two story house. This from memory but I...

Are they worth the money?it’s time for new boots unfortunately we don’t have but a few boot stores in town of 300,000

You forgot to add using one with a sgmi for pernament installation :cheers::whistle:

Not sure how you would be contaminating units the seals may shrink , and not seal. Most say use to gain access to the system then braze permanent access. If you’re doing for disposal I don’t see...

Most 75k have a three ton blower moving around 1200 cfm sorry no help on the load calc

The Asians are a hard sell they will go the cheapest route, and always want to negotiate. I have a son in law that is Vietnamese that sold cars he didn’t like to deal with Asians for that reason, but...

URI sells the 30x30” sheets I think that’s the size or get you a finneys gasket book for smaller stuff

Has any one read or seen this in the flesh, worth the$$?
https://trutechtools.com/paperback-ac-service-tech-inverter-mini-split-operation-andservice-procedures-by-craig-migliaccio.html

Kraut season is over gave som to the guy at the liquor store

Agree but their trillions of dollars in debt ironic

I believe what Dave Ramsey says about the student loans. You can’t go to the bank as a 18 year old and borrow 150k start a business, but you can borrow that much in student loans. Point being if they...

Like anything it’s what you put into it I was a misbent youth with a problem with authority. I still am but I have learned to focus my aggression else where. Depending on what mos ( job) he chooses...

Don’t remember the brand but I worked on one that wouldn’t close randomly. I was greener than green long story short it relied on back pressure to close so if someone flushed a toilet or large water...

David hill hasn’t been on here in about 8 years you may want to try a different route

They make a 3/4 hp in 115v ? My mistake
https://www.tecumseh.com/userfiles/documents/marketing-brochures/tec-quick-select-guide_na_en.pdf

How long has this been installed? Condensate installed correctly?
https://hvacdirect.com/media/hvac/pdf/N95ESN-Installation-Manual.pdf
See pages 12-15
Apply for pro membership

Howard reach in

23#’s of soon to be sauerkraut the wait is on

The auto industry is a complete different animal imo. First you don’t have haul everything you own to the roof in crappy conditions. There is no on call your time is yours. And as far as job security...

My 2cents with a setting of 45f it’s being used as a economizer or as combustion air if it’s oil or fuel

I doubt it but get a water test done from a reputable water treatment company, and see what the dissolved solids are. See if they have recommendations

We have used it in the trane 3d splits with mixed results. What’s kind of weird it the evaps are about 20’ higher than the condenser so you wouldn’t think oil return would be a issue

I thought this may have been a relative of feng

If I’m reading your post right not sure you will make minimum line set length. Without insulation not sure 1t will be enough

I think we all have touched up a rub mark on cap tubes without splicing. In reality the braze is stronger than pipe according to Harris :cheers:

Sounds like you were undercharged and over heated the compressor, what refrigerant, what are your pressures, does it have receiver and sight glass? Not to sound like a a$$ but we need as much info as...

Wonder what he knew about Hillary :couchhide::couchhide:

Wow that’s good news I wasn’t sure a refrigeration guy ever truly retired :cheers:

I would of thought he could get professional status

Thanks for the info I hope your wrong on his passing, but none of us are going to make of this rock alive

Sorry I’m not sure but based on the arrows and the labeling I would say it’s a fancy isolation valve as their isn’t any test ports or a way to lock it in persay wish I knew for sure good luck :cheers:

Not sure what got me thinking about this but checked his activity, and it looks like he hasn’t visited in three years. Did I miss something hopefully he , and his family is wee:cheers:

Don’t think I seen one made in Thailand before

Are you referring to nci? If so I haven’t taken this course, but have taken the combustion course. If has half the info that class has you’ll need to take it at least twice to absorb the info

I would probably go with making them remote, and possibly with multiple evaps on single condensers

I think I scared him when we went:whistle: wonder if he missed the same question as last time:beat:

Take paper and take notes a overload of info was disappointed that there was almost no hands on at the class I took. None the less a ton of information still digesting to this day

Last one I worked on was a domestic freezer pretending to be a commercial unit. We sold them to churches or low volume restaurants

This from Werner ladders I’m guessing your employer knows your a big boy?

Only downside is if a regulator or a hose ruptured ( had it happen in market work) it’s a long way to the shut off

Longest I ever worked 3 days strait done with that I’m almost 50 I need more me time than I need the ot

A bag of frozen peas on the nads helps

Not sure but it sounds like the sensor is on the discharge line? If so check compressor sh.

Get your post count up and apply for pro lots more on the other side

https://www.youtube.com/watch?v=PZpH9Khn0E0