Search:

Not sure what else to say - the controller is a DELTA DSC-1616E and the software is orca fully licensed. We see the program but can open them to view the program. It's locked out as an OEM and we are...

It's a delta panel and won't allow us to view the programming. Another delta panel we can view the program.

Make sure to get the naasia folder, which is the C-Tools

Drop Box - C-tools with patches available for 2 days

https://www.dropbox.com/scl/fi/b6k6b58ym1w8zzcrysi59/Naasia.zip?rlkey=b294z0wpoaajtyhnw5sjix4r4&dl=0

Seems like the wrong group to ask this question - sorry moving on

Good day,

Looking for some suggestions on techniques used for controlling an ice plant in terms of equipment. Like should we run the compressors longer (2hours) or shorten our diff and cycle more....

The output is triggering on\off (based on the trend) when the contactor isn't pulled in. We have a trend on the command which enables the contactor so we compared the two and it's not close. So we...

Adjustable and has been adjusted. The MMC cabinet are so tight that the contactor load wires are pretty close to each other.

Thanks

https://docs.johnsoncontrols.com/bas/v/u/Johnson-Controls/en-US/CSD-Series-Current-Devices-Product-Bulletin

Sorry correct link

Good day,

In our MCC control cabinet, we have several 3phase contactors. We are using the CSD current sensors (below is the link to the cut sheet) but fine that they are being triggered with noise...

That's correct. I guess moving forward anything over 150 on the primary will get grounded on the secondary and any transformer that is 120 to 24 won't.

Took a look at NEC for primary voltages over 150 volts.

This makes sense, based on my two situations. I was thinking grounding the secondary was going to create a ground loop for the DDC system.
...

That's exactly what we are seeing. The JCI control panel with transformer (120 to 24) we purchased doesn't have the secondary grounded. Then we purchased a newer transformer to replace the one in our...

Good day,

Our electricians mentioned that one side of the secondary of the transformer should be grounded. I've never seen the transformer to ground only the case. The diagram of the transformer...

have you figured this out

9.0.6 - check email. last version for windows

are you still looking for 9.03 and 9.07

do you have the NUT and SCT software

Yup - and from what I understand they aren't replacing the MPM with something else. So if you have VT7200 that is wireless and the MPM craps out, a complete upgrade.

Hello,

We have several of the MPM (GW2-0I0-00) from Viconics \ schneider working wireless with zigbee pro to the VT7200 stats. Does anyone know what the replacement is for the MPM keeping the...

Hello,
We have full admin access to ORCview, that's not the issue. The program is locked down so we can't even view the programs. So Nembus mentioned to download the program from OCRview to the...

Hello,

Are you referring to the reload option in ORCview

Thanks

Hello,
We have a Delta program and only want to view the program in the text file to see how it was controlling a piece of equipment. When we try to open the program, it says the program is an OEM...

Leakcheck
Can you also send me the link to download the can2go. Thanks

without CCT, schedules are out of luck from the CGM - if they used schedules from the SNE which is most likely what they did. They needed to program the CGM to use schedules which is never done.
...

Check the CCT logs

The metasys_application log at C:\ProgramData\Johnson Controls\MetasysIII\CCT\UI

Hello,

Just to be clear that it's wired correct, the 240V from one side of the transformer is going to the 240 Terminal and the 240V from the other side of the transformer is going to terminal #2....

Hello,

We have a Penn P28 Series Lube Oil Control with Built-in Time Delay Relay in a safety circuit for a compressor. It's not turning on the compressor only a safety in series with the low and...

Hello,

Does anyone know of a MSTP thermostat for a dehumidifier. I've looked around and I can only find one's which are for RTU etc like the JCI TEC or Viconics. But nothing for just a...

Are you talking about the supervisory controller from the 90's

Not sure if you tried this, connect your PC to a switch and to the NCE. Start the NIC tool software in Admin rights and power cycle the NCE. See if anything pops up in the NIC tool.
If not, if the...

You need to take the DMO and using bob's tools run it through the program which will produce the proper outputs for the NAE. You can't use CSAD "PM6OU1",N,N,"ZN-CTL14","" . For example below, here's...

Good point, why offer a loop in the NAE if you can't use it as a PID only to view another loop.

Haaa sorry misread your first post. The Loop in the NAE is only for viewing properties of a loop object in another BACnet device. Really not sure if it'll work with N2.

If you need to pass...

Im not sure what your refence is for loops in the NAE.

N2 points can't be linked from controller to controller like you can for BACnet objects (pier to pier) . But you can use control logic in...

Now if you are talking about the DX PID Loops, you need to map in the OCM and EF of the pid. OCM is the output of the PID in %. The EF (if setup in the PID) will enable to disable the PID. Both of...

Hello,

We have a Can2Go or MPM-GW Wireless Manager and need to figure out the password or how to reset the unit. Does anyone know how to factory default the password. The manual says admin admin...

Also look at these log files
C:\Program Files (x86)\Johnson Controls\Metasys UI\MetasysFacility.Service.log
If they doesn't show much you can change the logging by changing the...

Not sure if my post worked, but you need to check the Device Manager Server and see if's it running. Look on the ADS server - Services.

you can use Uberdebug to capture the startup sequence of Metasys III

Do you know if the BUILTIN\Administrator"s" was selected for the SQL administrator

You need to log into SQL and verify this.

It has to be set to Mixed mode and Not Windows Auth

You could have a corrupt Metasys III database. But first you need to be sure the SQL instance has been set for mixed-mode authentication and not Windows authentication. This would give you the...

Hello,

Has anyone have experience with using a BACnet Web Services and then creating a Web page.



Thanks

Hello,
Just to understand this, you have a true NCM350 with the DDL and GPL files. And you have a NCM4510-2 which you want to convert to a standard NAE4510-2 with N2. If this is the case, you'll...

The application in the folder is call DMO to DDL.

Here's the output from a DX program which DCO1 is BD1

* MODULE DCO 1
CSMODEL "DCO","DX9100"
ADTITLE "Analog Data"
BDTITLE "Binary Data"...

You need BOB tools. Not sure who made it way back when, but it'll convert the DMO to a file which has the proper mapping for the NAE. But it needs to run under 32 bit.
...

Crazy - 50 years in bussiness, 18000 laid off..

Due to hardships from the pandemic over the last few years, Douglas Lighting Controls will be ceasing operations after several decades of service to...

Just confirmed with our local rep, they're closing shop.