Search:

Type: Posts; User: anthonyac1

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    8
    Views
    258

    I appreciate the knowledge. Ima show up there...

    I appreciate the knowledge. Ima show up there early in the morning to put in the motor. I didn't want to wait for Rheem to open to find out. Just curious how did you find the info. Maybe from...
  2. Replies
    8
    Views
    258

    rheem condenser fan specs

    i went to a rheem condensing unit today. The condenser fan had shorted windings. on the condensers name plate it states 1.2 rla 1/5hp in the unit was a rescue motor 1/6-1/3 hp. 1075 rpm but rated...
  3. Replies
    4
    Views
    336

    Here in sunny south florida in the winters it...

    Here in sunny south florida in the winters it doesn't get cold. Maybe 0ne night it will hit 35-40 degrees f. But anyways with the condensers running it won't get to cold up there. But mainly our...
  4. Replies
    4
    Views
    336

    ambient temp. comditions

    I was at a school the other day and there were 4 walk in coolers with there condensers up in the ceiling. it was 114 degrees up there. There are about 5 ceiling tiles that are missing in the drop...
  5. Replies
    2
    Views
    259

    tecumseh start components kit

    just like danfoss makes a kit with a few body styles and different cartridges they put a kit together to keep on the truck. well for Tecumseh I thought I read on here that they have a similar kit...
  6. Replies
    15
    Views
    684

    The txv will respond to the low suction line temp...

    The txv will respond to the low suction line temp could be due to low airflow causing the valve to do its job and close down. I'm not arguing with what anyone is saying nor going against what has...
  7. Replies
    15
    Views
    684

    Your right about not adding ref. with 25 degree...

    Your right about not adding ref. with 25 degree subcool. I added refr. About 2 lbs and my subcool went up to 25 but it could have been 22 degrees subcool but yes it's the same shhh. Something...
  8. Replies
    15
    Views
    684

    its a trane unit at a buddies house. I went by...

    its a trane unit at a buddies house. I went by there other night I wasn't in my van. when I go back to clean the coil and blower wheel ill check the static pressure. The blower motor and wheel is...
  9. Replies
    15
    Views
    684

    Weak fan motor

    I was thinking about it on this unit, it has a 30 degree split = low airflow. Ok so the coil and blower wheel are dirty but I don't see it clogged really bad. Ima clean them both and see how my...
  10. Replies
    0
    Views
    147

    core sense contactors

    looks pretty interesting I want to install one, and play with one...


    http://www.youtube.com/watch?v=Y0pNHwzKy6k
  11. Replies
    24
    Views
    1,531

    So can that flux will work with 15% silver...

    So can that flux will work with 15% silver brazing rod with steel??? Also could I use 5% or no it won't work
  12. Ok I looked up cold zone. In one of the...

    Ok I looked up cold zone. In one of the installation manuals says they all come with this transformer for the water pump. It is a buck/boost transformer the pump can only run on 230v. So if the...
  13. It's wired totally separate from the fans. The...

    It's wired totally separate from the fans. The fans are wired to the main terminal block and are controlled by 2 thermostats sensing the water leaving temp going down to the soft serve unit.
  14. A choke looks like a transformer but it has 2...

    A choke looks like a transformer but it has 2 wires in and out. It's wired In series with one leg from the motors hi voltage side. It's supposed filter the power before going to the motor. Also I...
  15. Replies
    24
    Views
    1,531

    I've used the regular white brazing paste/flux....

    I've used the regular white brazing paste/flux. But I've never seen a black one?? Sounds pretty good
  16. Replies
    24
    Views
    1,531

    http://www.emersonclimate.com/europe/ProductDocume...

    http://www.emersonclimate.com/europe/ProductDocuments/CopelandLiterature/Emerson_Assembly%20Instructions_E_1212_0.pdf check out page #4
  17. Replies
    24
    Views
    1,531

    It was already mentioned but is true. Every...

    It was already mentioned but is true. Every compressor I ever brazed in has steel fittings stubbed out but they are copper plated. If you over heat it you will burn the copper plating and will get...
  18. Replies
    5
    Views
    451

    Also check the run capacitor if it's single phase...

    Also check the run capacitor if it's single phase very important because your start components will start the comp. then if you have a bad run cap it will draw hi amps while struggling to run. Also...
  19. Or I should say the purpose of it and I'll let...

    Or I should say the purpose of it and I'll let you know what they say
  20. Ima look up the company and call them on Monday...

    Ima look up the company and call them on Monday describe it as best as possible and see what they say it is
  21. The nameplate is faded but when I look at it at...

    The nameplate is faded but when I look at it at an angle the brand looks like cold zone but never seen that brand
  22. No the condenser fan motors are regular Psc...

    No the condenser fan motors are regular Psc motors 1075rpm 1/2 hp.
  23. I think on my first meter that happened but the...

    I think on my first meter that happened but the problem is since the magnet is on the back of the battery cover it pulls the batteries slightly out of place but if you put a a piece of paper such...
  24. It had a start cap and I did not see a module to...

    It had a start cap and I did not see a module to convert the power to dc for an ECM motor. I don't think it was. It looked like a straight forward motor vac.
  25. I checked thinking it was a choke. But it wasn't...

    I checked thinking it was a choke. But it wasn't wired in series with the motor. L1 and L2 from the motor was fed from the transformer output.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event