Search:

Type: Posts; User: luv2cruiserccl

Page 1 of 12 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    6
    Views
    328

    So if I remove drain and install a liner and seal...

    So if I remove drain and install a liner and seal top that would help a lot I assume,

    Sent from my SCH-I545 using Tapatalk 2
  2. Replies
    6
    Views
    328

    80 percent with odd drain

    Hello all have any of u guys deen a older 80 percent furnace with some sort of homemade drain? Please see attached photo and tell me what u think. I am wondering if there is a real danger to this and...
  3. I can't pull up from phone so will so later...

    I can't pull up from phone so will so later tonight from home to see. What I saw was you drilled roughly a 3/8 hole and they where like a step bit and fit right in with just a single push.

    Sent...
  4. Combustion testing and co testing question

    Hello all I just have a quick question somewhere I thought I seen some plugs that u can use in either the flu or in air duct? I did some asking at a local supply house and they did not have any idea....
  5. Replies
    66
    Views
    8,830

    Sounds good. I been wondering if a inspection...

    Sounds good. I been wondering if a inspection camera thru the limit switch would work at all in helping to find these issues as well

    Sent from my BlackBerry using Tapatalk please excuse...
  6. Replies
    66
    Views
    8,830

    Did u happen to check the plastic cover plate...

    Did u happen to check the plastic cover plate that have a dozen or so screws in in that covers the actual secondary hx when I find tail piece issue I usually see that but not always

    Sent from my...
  7. Replies
    66
    Views
    8,830

    I assume that is the tail piece from secondary to...

    I assume that is the tail piece from secondary to comb blower motor?

    Sent from my BlackBerry using Tapatalk please excuse typographical errors
  8. Replies
    5
    Views
    429

    Thanks I will check it out tomm on computer. ...

    Thanks I will check it out tomm on computer.

    Sent from my BlackBerry using Tapatalk please excuse typographical errors
  9. Replies
    122
    Views
    14,621

    Andy!! All I can say is thank you I went out and...

    Andy!! All I can say is thank you I went out and got the timberland pro pit boss steel toe and I love them no break in at all in them for 10 hours a day and my feet never got sore at all and felt...
  10. Replies
    5
    Views
    429

    what i have its a multi story building that has...

    what i have its a multi story building that has several 3/4 inch sweat solenoid valve's and circuit setter. I have installed a few taco erie vt2313g13a02a...2way 24 volt. this style i replaced a few...
  11. Replies
    5
    Views
    429

    Solenoid valve

    So guys what are a good quality long lasting 24volt 3/4 inch sweat solenoid valve's. I am going to have to replace a lot this summer and want a good quality one. Any suggestions appreciated.

    Sent...
  12. I can provide some info and kit numbers if u send...

    I can provide some info and kit numbers if u send me a pm on here and I will fwd info.

    Sent from my BlackBerry using Tapatalk please excuse typographical errors
  13. Ya the support bracket welds broke and that shaft...

    Ya the support bracket welds broke and that shaft was riding that bracket and just about cut in all the way thru. Made a ton of noise!! Wink! I have seen that style blower come loose in the middle...
  14. does your unit look like this?

    does your unit look like this?
  15. Could use a dial indicator and check to see if...

    Could use a dial indicator and check to see if that shaft is bent as others stated. This the type that the two half's of the blower wheel are welded together? if it is that style then I have seen...
  16. Also forgot to ask how is your belt tension ...

    Also forgot to ask how is your belt tension

    Sent from my BlackBerry using Tapatalk please excuse typographical errors
  17. If u have acess to a sheave laser alignment tool...

    If u have acess to a sheave laser alignment tool I would use it that will cause vibration. Also u said u had new motor the motor could have a soft foot issue if u loosen one bolt at a time and run...
  18. Replies
    24
    Views
    3,187

    Looks nice sent from my kindle fire using...

    Looks nice

    sent from my kindle fire using tapatalk 2 please excuse any typographical errors using tapatalk
  19. Replies
    8
    Views
    623

    For? Have pm on site open to send works for me. ...

    For? Have pm on site open to send works for me.

    sent from my kindle fire using tapatalk 2 please excuse any typographical errors using tapatalk
  20. Replies
    5
    Views
    433

    Sent u a pm message here got some more info on...

    Sent u a pm message here got some more info on this

    Sent from my BlackBerry using Tapatalk please excuse typographical errors
  21. Replies
    8
    Views
    623

    Did so more looking in to this and found a break...

    Did so more looking in to this and found a break in t stat wire all is well now. Thanks

    Sent from my BlackBerry using Tapatalk please excuse typographical errors
  22. Replies
    8
    Views
    623

    Problem is I don't have a book that came with...

    Problem is I don't have a book that came with rtu..

    Sent from my BlackBerry using Tapatalk please excuse typographical errors
  23. Replies
    8
    Views
    623

    Sorry for title spelling stupid auto spell on...

    Sorry for title spelling stupid auto spell on kinkle thanks

    Sent from my BlackBerry using Tapatalk please excuse typographical errors
  24. Replies
    8
    Views
    623

    Grand ignition issue

    Hello all I got a trane rooftop ycd241c4lrcb. And I can not get it to run in heat with Dc tstst. If I jump from test 1 and 2 unit get to heat portion unit will fire right up. Is there anything...
  25. Replies
    13
    Views
    1,296

    i tryed to send you a a pm message nut you got...

    i tryed to send you a a pm message nut you got them off. I know you said it was a 120k but you sure its not 150k?

    Was that trane rooftop you had a YC*150, 151, 180, 181, 210, 211, 240, 241, 300,...
Results 1 to 25 of 283
Page 1 of 12 1 2 3 4
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event