Search:

Type: Posts; User: contrltech

Page 1 of 3 1 2 3

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    3,649

    JCI Metasys SCT problems

    I purchased the MS-SCTSWO-0 software package from my local branch.
    I followed the install instructions exactly and I was able to get CCT to work.
    When I click on the SCT icon all I get is a HTTP...
  2. Replies
    5
    Views
    515

    Yes, because it operates at higher speeds it's...

    Yes, because it operates at higher speeds it's more prone to
    "issues" on a maginal network. N2 runs at 9600 whereas MS/TP
    goes all the way up to 156k, although it is usually set around 38 to 56k....
  3. Replies
    1
    Views
    520

    The CCN converter box that comes with Network...

    The CCN converter box that comes with Network Service Tool has the software key built-in. I'm not sure if you have to have the box plugged in to install the program.
  4. Replies
    5
    Views
    515

    It depends on the condition of the wiring. N2...

    It depends on the condition of the wiring. N2 runs at a lower baud rate than the average MS/TP network. If all the wiring is in good shape and the physical network configuration is ok (no T taps,...
  5. Replies
    27
    Views
    6,839

    I got NST version 5 a few months ago and it works...

    I got NST version 5 a few months ago and it works great!
    I haven't had any problems running it on XP and it sure is nice
    being able to use the USB interface.
  6. Replies
    3
    Views
    462

    Check your inbox

    Check your inbox
  7. Replies
    16
    Views
    1,421

    I installed the kit mentioned in the service...

    I installed the kit mentioned in the service bulletin on a 30GTN
    about six months ago and haven't had a problem since.

    The kit is only about $100 and it's worth every penny!
  8. Replies
    7
    Views
    640

    Just a thought: the FX40 is limited to 100...

    Just a thought: the FX40 is limited to 100 devices or 1000 points, whichever comes first. I don't know what a MIG is or what it's doing in the network, but I have had odd problems like this come up...
  9. Thread: Fx Vma

    by contrltech
    Replies
    8
    Views
    936

    THANKS!

    THANKS!
  10. Thread: Fx Vma

    by contrltech
    Replies
    8
    Views
    936

    Well, that's nice.... I just got back from the...

    Well, that's nice....

    I just got back from the FX controller programming course and the instructor
    said release 3.0 had the app with it.

    I know it's not available on FX exchange.
  11. Replies
    0
    Views
    464

    Triatek Lab controllers

    Does anybody have experience with Triatek Lab controllers?

    Here’s my problem:

    I need to change the minimum airflow settings for several VAV-1000L
    controllers in an existing project. I also...
  12. Thread: Fx Vma

    by contrltech
    Replies
    8
    Views
    936

    I have some on order but I haven't got them yet....

    I have some on order but I haven't got them yet.

    I'm told the programming in the controller is very similar to the original VMA.

    FX Tools 3.0 will include the builder express app to configure...
  13. Replies
    5
    Views
    1,029

    Alerton Microset two

    Does someone have a copy of the tech manual for Alerton's Microset II
    sensors? I need to access field service mode to make some changes
    but I don't have the tables that tell me what the values are....
  14. Replies
    22
    Views
    2,489

    York 160.48-M2 service instructions

    Does anyone have this file in a PDF that they could send me?

    My email address is in my profile.

    Thanks in advance!!!!
  15. Replies
    16
    Views
    5,081

    Carrier Network Service Tool V

    Does anyone have Carrier's part number for the network service tool version V?

    Thanks in advance!!
  16. Replies
    7
    Views
    773

    The FX40 is able to access a Trane Comm5 network....

    The FX40 is able to access a Trane Comm5 network. If the FX40 database doesn't have the plugins you can get them from echelon's website.
  17. Replies
    4
    Views
    554

    You can try using the USB adapter with LonSpec...

    You can try using the USB adapter with LonSpec but it is not
    officially supported. I have used it before and it does work with some
    computers.
    The only "supported" non-serial interface is the...
  18. Replies
    23
    Views
    4,253

    Once you configure your network connection on...

    Once you configure your network connection on your computer open IE and type the
    IP address of the platform in the address bar. If everything was set up right, you should see a screen asking you to...
  19. Replies
    8
    Views
    925

    Thanks Ausccn. That's what I was looking for.

    Thanks Ausccn. That's what I was looking for.
  20. Replies
    8
    Views
    925

    Does anyone have a complete list of the old...

    Does anyone have a complete list of the old Flotronic controller
    error codes?

    Thanks in advance!!
  21. Replies
    12
    Views
    1,852

    I second that. I think the lit. on the P66 even...

    I second that. I think the lit. on the P66 even says you must use a motor
    with ball bearings.
  22. Replies
    12
    Views
    1,007

    Do you have any particular controller in mind? I...

    Do you have any particular controller in mind? I have a bunch of FX07
    preconfigured apps and quite a few mcr files I can send you.
  23. Replies
    11
    Views
    978

    I use a Dell Latitude ATG620. Extremely pleased...

    I use a Dell Latitude ATG620. Extremely pleased with it - and it has a built in serial port!
  24. Replies
    5
    Views
    1,019

    gerizam60, if you add your email address to your...

    gerizam60, if you add your email address to your profile I'll send you the login info.
  25. Replies
    26
    Views
    4,735

    Reaper, Please send me the mcr files also. I'm...

    Reaper, Please send me the mcr files also.
    I'm working on designing pump rotation assemblies - If I
    can look yours over it would be a great help.

    THANKS!!!

    Email is in my profile.
Results 1 to 25 of 61
Page 1 of 3 1 2 3
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event