Search:

Type: Posts; User: Achicagoperator

Search: Search took 0.00 seconds.

  1. I often find pm issues the hardest sell for a...

    I often find pm issues the hardest sell for a customer to cough up for unless there's strong visual or audible proof that a specific component may fail sooner than later.As stated in above posts you...
  2. Replies
    32
    Views
    3,834

    The Chicago breakdown for stationary engineers as...

    The Chicago breakdown for stationary engineers as far as cards\titles are concerned is as follows..........1)Chief....2)Assistant Chief........3)A Card.......4)C Card.....5)Apprentice.
  3. Replies
    26
    Views
    2,560

    :gah:I hated when meggering pm time came...

    :gah:I hated when meggering pm time came around.Would almost hope to find something grounded just to prove to myself that i wasnt completely wasting my time.If everythings running properly i see no...
  4. Replies
    10
    Views
    1,025

    :gah:Been there done that.The zap to my pride is...

    :gah:Been there done that.The zap to my pride is almost as bad as the zap to my body.
  5. Replies
    17
    Views
    1,559

    i agree, a good mix supports progress and also...

    i agree, a good mix supports progress and also feel that the further one gets into a program the more hands on learning/troubleshooting should be stressed.Students need to apply what they've learned...
  6. Replies
    26
    Views
    3,028

    ABB,tops in my book.

    ABB,tops in my book.
  7. Replies
    30
    Views
    3,278

    Where is your cw temp sensor located,sounds like...

    Where is your cw temp sensor located,sounds like theres nothing telling the fans to stage.You will experience some water temp fluctuations at startup but you shouldnt be 25 degrees above setpoint...
  8. Replies
    2
    Views
    716

    Centrifugals are typically larger tonnage systems...

    Centrifugals are typically larger tonnage systems that utilize an independent oil pump to distribute oil to the gears,bearings,etc.
  9. Replies
    6
    Views
    744

    Pressure test with your inert gas,let stand,pull...

    Pressure test with your inert gas,let stand,pull your vacuum 300 to 500 microns,let stand,should be ready to charge.
  10. I see why they doubled my water bill.City jobs...

    I see why they doubled my water bill.City jobs the way to go.
  11. Replies
    13
    Views
    1,333

    furthest cop to the left........."as soon as he...

    furthest cop to the left........."as soon as he hits boys we need to run before PETA gets here."
  12. Take the job with the Water Department.Hands down...

    Take the job with the Water Department.Hands down the best jobs going.Although you should find out how long[timeframe] the project is because you may be laid off upon completion.
  13. Replies
    31
    Views
    3,654

    Be motivated even if your doing menial...

    Be motivated even if your doing menial things.Even the best techs started at the bottom.
  14. Replies
    35
    Views
    3,510

    I agree that staying in school is a good start.If...

    I agree that staying in school is a good start.If your passionate about this trade you'll learn and doors will open eventually.Knowing a politician may help also.
  15. Know the refrigeration cycle and the major...

    Know the refrigeration cycle and the major components,compressor,cond,etc.Know some basic definitions for latent heat,sensible heat,etc.Be confident,a good interviewer will be rooting for ya and want...
Results 1 to 15 of 18
Comfortech Show Promo Image

Related Forums

Plumbing Talks | Contractor Magazine
Forums | Electrical Construction & Maintenance (EC&M) Magazine
Comfortech365 Virtual Event